Milleteknik 4U010000P00019P01 19 Rack Module Holder Instruction Manual

Milleteknik 4U010000P00019P01 19 Rack Module Holder

Product Information

The product is a backrest support designed to provide comfort and support while sitting or lying down. It is suitable for daily use and has a service life of five years when used according to the safety instructions and maintenance intervals mentioned in the user manual. The product complies with ISO 13485 quality standards and is classified as a Class I medical device under the Medical Device Regulation 2017/745. It also features the CE mark and UKCA mark, indicating compliance with relevant regulations. The product is made using REACH-compliant materials and components.

Product Usage Instructions

1. Before using the backrest support, carefully read the user manual provided.
2. Ensure that the product is in good condition and all components are intact before use.
3. If there is any damage or if the product is not functioning properly, contact your Invacare provider for further instructions.
4. The backrest support can be used while sitting or lying down to provide comfort and support.
5. Follow the recommended safety guidelines while using the product.

ABOUT 19 RACK MODULE HOLDER AND 19 RACK DIN MODULE HOLDER

19 rack module holder and 19 rack DIN module is a four unit high enclosure for mounting in 19 “racks or on a wall. 19 rack module holder has a lockable door in plexiglass and comes with tamper connector as standard. The unit is also available with mounted DIN rail for to attach options such as circuit break- ers, power supplies or other components that have a DIN rail bracket.With DIN rail mounted, the unit is called: 19 rack DIN module holder.

19 rack module holder

Sheet metal housing for 19 “rack or mounting directly on the wall, the product comes with a tamper switch.

19 rack DIN module holder

• Sheet metal housing with DIN rail for 19 “rack or mounting directly on the wall, the product comes with a tamper switch.
• Cable entries may vary depending on the version of sheet metal housing, the number of card slots is the same in the different versions.

Component overview

19 rack module holder

Component overview

Mounting 19 rack module holder

• The unit can be mounted in a 19 “rack or on a wall.
• When mounting in a 19 “rack, screw in the upper holes in the bracket.
• When mounting on a wall, use a suitable screw and plug for the wall.
• Remove protective plastic on the cover after installation.

Notice

Always screw with at least two screws in each bracket.

Positions for cards in 19 rack module holder

• Number of places for circuit boards with a larger form factor: 4 pieces -marked 1-4 in the picture.
• Number of places for circuit boards in the smaller form factor (L-module): 12 pcs – marked a-c in the picture. However, 8 (horizontal) optional cards have the most space (a, c), as the grooves in the middle (b) are adapted for standing cards.

Note

• It is the installer’s responsibility to consider wiring and cable lengths when installing circuit boards.

19 rack module holder with a card mounted in place 1

• To the right is a card in the smaller form factor, for place a-c.
• At the bottom right are plastic ends short of the larger form factor. These can be in place 1-4 or (5) DIN rail.

Installation of optional card in 19 rack module holder

• Snap the card to any position (1-4, a-c, depending on the card’s form factor / size).

Installation of optional card in 19 rack module holder

• Secure the card with the supplied screw to any position (1-4).

Adjustment of tamper switch

The tamper switch lever must be in the closed position when the cabinet door is closed. If the alarm goes off (“tamper alarm”), the lever may needs to be adjusted.
The lever is adjusted by the following steps:

1. Pinch with pliers in the middle of the lever.
2. Carefully adjust the lever in the desired direction (up / down).
3. Check by closing the door. A click is heard when the contact is closed.

Notice
Tamper switch will not give an alarm when closed and locked the door.

Technical Data

19 rack module holder and 19 rack DIN module holder

and/or alarm device monitoring card. It is also possible to use the module together with Linjator’s

connection modules and/or Sentrion DSS

modules.

| Sheet metal housing with DIN rail for 19 “rack or mounting directly on the wall, the product comes with a tamper switch.
---|---|---
Number of module slots| 8 pcs. L-modules or 4 pcs. 10 output modules or 4 pcs. Fire module 4 outputs. It is fine to mix cards among module slots, but the number of module slots cannot be increased.| 20 pcs. circuit breakers
Tamper switch| Yes
The prod- uct fits in| Battery backup with PRO3 card.
Rack units:| 4RU
Material| Sheet metal enclosure in powder-coated sheet metal with lockable plexiglass door. Tamper switch included.
Measure| Width: 482,5, height: 173 mm, depth: 108 mm

• Manufactured in Milleteknik’s factory in Partille, Sweden.
• This translation is not verified and should be cross referenced with the swed-ish original before use.

Technical data: Tamper switch

Support

• Do you need help with installation or connections? Our support phone is avail-able: Monday-Thursday 08: 00-16: 00 and Fridays 08: 00-15: 00.
• Telephone support is closed between 11: 30-13: 15.
• You can also send e-mail, we respond, on weekdays.
• Address and contact details
• Milleteknik AB
• Ögärdesvägen 8 B
• S-433 30 Partille
• +46 31 340 02 30
• www.milleteknik.se

Documents / Resources

| Milleteknik 4U010000P00019P01 19 Rack Module Holder [pdf] Instruction Manual
4U010000P00019P01 19 Rack Module Holder, 4U010000P00019P01, 19 Rack Module Holder, Module Holder, Holder
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>