beper P206VEN650 Ceiling Fan with LED Light Instruction Manual
- June 12, 2024
- beper
Table of Contents
beper P206VEN650 Ceiling Fan with LED Light Instruction Manual
Precautlons
Read the following instructions carefully, since they give you useful
safety information about installation, use and maintenance and help you avoid
mishaps and possible accidents.
Remove the packing and make sure that the appliance is intact, with special
attention to the supply cable.
The elements of the packing (plastic bags, polystyrene, etc) do not have to be
accessible to the children, in order to preserve them from danger sources. It
is recommended not to throw these packing material in the domestic waste, but
to deliver them to the appropriate station of collection or destruction
refusals, asking eventually information to the manager of the Sanitation
Department of your own municipality.
If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
Before connecting the appliance make sure that the mains voltage corresponds
to the data specified on the label.
The appliance can be damaged if the voltage is not correct.
If the plug does not suit the socket, let it be replaced with another suitable
plug by qualified personnel only, which shall also ensure that the section of
the socket cables is suitable for your appliance power absorption. Generally,
the use adaptors multiple plugs and/or extensions is not recommended; should
they be necessary, please use only simple or multiple adaptors and extensions
in compliance with the safety rules in force, making sure that the capacity
absorption limit marked on the simple adaptors and the extensions and the
maximum power limit marked on the multiple adaptor are not exceeded. Do not
use the appliance if the cable or the plug shows any damages. Do not use the
appliance after a possible irregular working. In this case, switch it off and
do not break it open. Refer to an authorized Beper after-sale service for
repair and require original spare parts only. Failing to follow these
instructions may impair the safety of your appliance.
This appliance is to be destined to its special purpose only. Any other use is to be considered as improper and thus dangerous. The manufacturer cannot be responsible for any damages deriving from improper, wrong or incautious use.
This appliance is for household use only.
To protect against electric shock, do not immerse cord, plug or any parts of
the appliance into water or other fluids.
Do not use the appliance near explosives, highly flammable materials, gases or
burning flames.
Do not allow children, disabled people or every people without experience
or technical ability to
use the appliance if they are not properly watched over. Close supervision is
necessary when any appliance used by or near children.
Warnings for use
ATTENTION! CONTACT QUALIFIED TECHNICAL PERSONNEL TO INSTALL THE FAN.
The appliance must be installed at least 2.3 m from the walking surface (2.3 m are intended from the walking surface to the bottom of the fan).
Do not insert objects and/or fingers inside the grid when the fan is operating.
Always unplug the fan from the power mains before carrying out any cleaning or maintenance operations.
Do not immerse the appliance, its cable and plug in water or other liquids – do not spray water or other liquids on the appliance, its cable or plug.
Do not operate if the appliance and/or its power cable show visible damage or
malfunctionings.
Do not use in the presence of explosive or flammable gases.
Do not use the fan outdoor or in the proximity of water containers such as
bathrooms or laundry rooms. Do not install the fan where it might fall in
water, e.g. near bath tubs, pools, water basins or other containers.
Do not use the fan near curtains, plants, drapes, and near objects that might
get trapped in the blades.
In case of malfunctioning or abnormal noise, interrupt the operation of the
appliance immediately.
Do not cover the appliance with cloths, garments, drapes, etc.
This appliance can be used by children 8 years of age or older, and by people
with reduced physical, sensory or mental abilities, or with limited experience
and knowledge, provided they have been supplied with complete instructions on
the safe use of the appliance. appliance and that they understand the
associated risks.
Children must not play with this appliance.
Cleaning and maintenance cannot be carried out by unsupervised children.
For the safety of children and pets, remove and dispose of all packaging
material before use.
This fan is intended for home use only, as described in this manual. Any other
use is to be considered improper and, therefore, dangerous.
Warning: if during operation the fan should move abnormally, immediately stop the operation, and contact your trusted electrician or the professional who carried out the installation.
Always use original spare parts, contact the after sales service referred to
in this manual and qualified technical personnel for any repair or maintenance
operation.
Means for disconnection must be incorporated in the fixed wiring in accordance
with the wiring rules.
Important: ceiling anchors and screws used for the mounting of the bracket to the ceiling must be able to withstand a weight 4 times higher than that of the fan (weight of fan: 3 kg)
Description of product
- Ceiling anchors
- Ceiling fastening screws
- Ceiling bracket
- Bracket fixing screws
- Terminal block
- Remote controller
- LED light ON/OFF key
- Fan OFF key
- Fan speed selection keys
- Increase light intensity key
- Decrease light intensity key
- Color selection key (warm/fcold/neutral)
- Light color dimmer key
- Timer setting key (1h-2h-4h)
- Night mode key
Installation Fig.A
The installation of the fan must be carried out by qualified and specialized technical personnel – contact your electrician for further assistance.
Remove the ceiling bracket from the fan, unfastening the 4 screws with a
Phillips screwdriver (not provided).
Using the holes found on the bracket as guide, drill the holes on the ceiling
making sure thy are deep enough to fit the ceiling anchors.
The fan must be installed at least 2,3 m from the floor (2,3 m are calculated
from the floor to the lower side of the fan).
Warning: if the fan is installed on plasterboard or wooden ceilings or false ceilings, use plugs and screws suitable for these materials.
Install the bracket to the ceiling with the screws provided. Then proceed to
connect the fan to the power supply as shown in Fig.A.
Once the connection is set up, insert the fan on the bracket previously
installed on the ceiling, and fasten the fan to the bracket with the 4 screws
previously removed.
Make sure that the screws are well fastened, and that the fan is securely
fixed to the ceiling.
Operation FIg.B
To activate the remote controller, insert the 2 alkaline batteries type AAA
(not provided) inside the battery case, making sure to respect the polarity
indicated.
To activate the LED light, press the ON/OFF key; the color (warm, neutral,
cold) can be selected by pressing the color selection key – the light
intensity will be at max level.
For each light color, the light intensity can be adjusted by pressing the
increase/decrease intensity key; it is also possible to gradually change the
light color, by pressing the color dimmer key.
Select the fan speed by pressing the relevant key related to the desired
setting (low speed, medium speed or high speed). Press the fan OFF key to stop
the rotation of the blades.
To activate the automatic switch off timer, press the relevant key for the
desired setting (1h-2h-4h); when the timer goes off, the fan and the light
will automatically shut off.
Night mode can also be selected: fan speed stays on low, while the LED light
is set on the lowest intensity level and warm color; to activate this mode,
press the relevant key on the remote controller.
Cleaning and maintenance
Make sure the appliance is switched off before carrying out any cleaning
operation.
Remove dust or stains from the outer surface using a soft dust cloth, or a
soft cloth slightly dampened.
Warning: do not let water or other liquids penetrate inside the fan; do not
spray water or other
liquids directly on the fan.
Remove batteries from the remote controller if not used for long periods of time.
Technical data
LED light power: 40W
Fan power: 40W
220-240V 50Hz
For any improvement reasons, Beper reserves the right to modify or improve
the product without
any notice.
The European directive 2011/65/EU on Waste Electrical and Electronic Equipment
(WEEE), requires that old household electrical appliances must not be disposed
of in the normal unsorted municipal waste stream. Old appliances must be
collected separately in order to optimize the recovery and recycling of the
materials they contain, and reduce the impact on human health and the
environment.
The crossed out “wheeled bin” symbol on the product reminds you of your
obligation, that when you dispose of the appliance, it must be separately
collected.
GUARANTEE CERTIFICATE
Beper is only liable for manufacturing defects and malfunctions caused by such defects; the warranty does not cover damage and/or malfunctions caused by incorrect installation. Any possible cost of installation, assembly and disassembly cannot be charged to Beper in any way.
This appliance has been checked in the factory. From the date of original
purchase a 24 month guarantee applies to material and production defects. The
purchase receipt and the guarantee certificate must be submitted
together in case of claim to guarantee.
The guarantee is valid only with a guaranty certificate and proof of purchase (fiscal receipt) indicating the date of purchase and the model of the appliance
For any technical assistance, please contact directly the seller or our head
office in order to preserve the appliance’s efficiency and NOT TO void the
guarantee. Any intervention on this appliance by non-authorized persons
will automatically void the guarantee.
GUARANTEE CONDITIONS
If the appliance shows defects as a result of faulty material and/or
production during the period of guarantee, we guarantee repair free of charge
on condition that:
- The appliance has been used properly and for the purpose for which it has been intended.
- The appliance has not been tampered with, otherwise it is not maintainable.
- The purchase receipt shall be presented.
- The appliance showing a fair wear and tear shall not be covered by this guarantee.
Therefore, any part that could be accidentally broken or having visible signs of use in consumable products (such as lamps, batteries, heating elements…) the aesthetic parts are excluded from the guarantee, and any defect whatsoever resulting from non-respect of the rules for use, negligence in usage and/or maintenance of the appliance, carelessness, wrong or improper installation, damage during transport and any other damage not attributable the supplier.
For every defect that could not be repaired within the guarantee period, the appliance will be replaced free of charge
In any case, if the part to be replaced for defect, breakage or malfunction is an accessory and/or a detachable part of the product, Beper reserves the right to replace only the very part in question and not the entire product Contact your distributor in your country or after sales department Beper.
E-mail assistenza@beper.com which will forward your enquiries to your distributor.