Euri Lighting EBPN22-40WS2000-2 LED Back-lit Flat Panel Installation Guide

Euri Lighting EBPN22-40WS2000-2 LED Back-lit Flat Panel

Product Information

The EBPN22-40WS2000-2 and EBPN24-50WS2000-2 are LED Back-lit Flat Panel series of 2×2 ft. and 2×4 ft. class respectively. These panels are designed and manufactured by Eurilighting. The panels come with a junction box that has a dimmer switch, AC-L, AC-N, GND, and a purple Dim+ wire. The panels can be installed using various methods such as recessed, suspended, and surface- mounted. Clips for the recessed mounting should be purchased separately.

Product Usage Instructions

Before installation, please review the instructions and warnings mentioned below:

Safety Instructions

• Switch off the power supply before installation.
• Switch on the power supply only after complete installation and examination of the circuit.

Caution

Make sure that the mounting surface or structural member used for installation can support the weight of the LED panel.

Installation Procedure

Recessed Mounting (Clips)

1. Cut out the ceiling plaster slab according to the cut-out sizes mentioned in the table.
2. Remove the knock-down hole on the junction box by screwdriver (Part A), remove the screw, and take out the driver cover (Part B).
3. Connect the wires as shown in the picture (Dim-, AC-L, AC-N, GND, Dim+).
4. Cover the driver box and tighten it with a screwdriver to finish the connection.
5. Fix the panel light into the plaster ceiling using clips.
6. Make sure the frame and panel light are firmly fixed, turn on the power.

Suspended Mounting

1. Fix the anchor into the target place on the ceiling.
2. Fix the installation mount on the ceiling with a plastic anchor.
3. Hang the panel to the ceiling with suspended installation kits and adjust the length of steel wires.
4. Feed the main AC wire in driver terminal block respectively and turn on the power.

Surface Mounted

1. Fix the anchor into the target place on the ceiling.
2. Fix the installation mount on the ceiling with a plastic anchor.
3. Hang the panel to the ceiling with suspended installation kits and adjust the length of steel wires.
4. Fix the side frame back by screw.
5. Feed the main AC wire in driver terminal block respectively and turn on the power.

Lamp Inspection before Installation

Take out the lamp from the box and put it on a flat table. If the lamp upwarps, please adjust the lamp with the following steps before installation:

1. Press the opposite angles at the same time.
2. Press another two opposite angles at the same time, make sure the four angles are flat, then start the installation.

Slide Switches for CCT and Power Selection

If your product comes with a slide switch for CCT or power selection, please select the CCT or power needed before installation. Ignore these steps if your product does not have this function.

PLEASE REVIEW THE INSTRUCTIONS AND WARNINGS LISTED BELOW PRIOR TO PROPER INSTALLATION

SAFETY INSTRUCTION

Basic safety precautions should always be followed when installing, including the following:

1. Read instructions carefully before installing.
2. This LED Panel requires professional installation and maintenance.
3. The power supply of the LED Panel should be powered by a dedicated external LED driver.
4. Disconnect the power supply before installation or maintenance.
5. Make sure the wires have been properly connected before powering on the device.
6.  Ensure the product has enough space for heat dissipation.
7. Ensure the luminaries are never covered by any heat insulation mat or slim layer material at anytime.
8. IP40 is for indoor use only, not for damp location; IP54 for indoor damp location.
9. Ambient Temperature: -10C˚ to + 45C˚, Avoid direct sunlight.
10. Storage Conditions: Cool & dry conditions.

WARNING

1. Switch off before installation.
2.  Switch on only after complete installation and examination of the circuit.

CAUTION

Make sure that the mounting surface or structural member used for installation can support the weight of LED Panel.

INSTALLATION PROCEDURE

1. Remove the knock-down hole on box by screwdriver (Part A), Remove screw, and take out the driver cover (Part B)
2. Connect the wire as the picture showing.
3. Cover the driver box and tighten it with a screwdriver, finish connection.
4. For the product with Slide Switch of CCT or power selection, please select the CCT or power needed before installation. (Ignore these steps if without the function)

Lamp inspection before installation: Take out the lamp from the box and put it in a flat table, if the lamp upwarps, please adjust the lamp with the below steps before installation:

1. Press the opposite angles at the same time;
2. Press another two opposite angles at the same time, make sure the four angles are flat, then start the installation.

RECESSED

1. Remove the ceiling plaster slab.
2. Feed the main AC wire in driver terminal block respectively, connect the panel light and driver.
3. Fix the panel light into plaster ceiling.
4. Make sure the led panel light is firmly fixed and turn on the power.

SUSPENDED

1. Fix the anchor into target place on the ceiling.
2. Fix the installation mount on the ceiling with plastic anchor.
3. Hang the panel to ceiling with suspended installation kits, adjust the length of steel wires.
4. Feed the main AC wire in driver terminal block respectively and turn on the power.

SURFACE MOUNTED

1. Fix the anchor into target place on the ceiling.
2. Fix the installation mount on the ceiling with plastic anchor.
3. Hang the panel to ceiling with suspended installation kits,adjust the length of steel wires.
4. Fix the side frame back by screw.
5. Make sure the frame and panel light are firmly fixed, turn on the power.

RECESSED MOUNTING (CLIPS)

Warning: Input wire diameter ≥0.75mm²; Product modification and improper installation are not valid for warranty.

• PRODUCT ILLUSTRATIONS REPRESENTED IN THIS INSTALLATION GUIDE MAY VARY IN SIZE DEPENDING ON THE MODEL NUMBER. INSTALLATION REMAINS THE SAME.
  ©2022. Euri Lighting
  A Division of IRTRONIX Inc. All Rights Reserved

• Questions?

• For customer service Please email us at info@eurilighting.com Office Hours: 8:00 a.m. – 5:00 p.m. PST Monday-Friday

• www.eurilighting.com

Documents / Resources

| Euri Lighting EBPN22-40WS2000-2 LED Back-lit Flat Panel [pdf] Installation Guide
EBPN22-40WS2000-2, EBPN24-50WS2000-2, EBPN22-40WS2000-2 LED Back-lit Flat Panel, LED Back-lit Flat Panel, Flat Panel, Panel
---|---

References

• HOME - Euri Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>