Mouses YC-JY201 RGB Wireless Mouse User Manual
- June 5, 2024
- Mouses
Table of Contents
Mouses YC-JY201 RGB Wireless Mouse
Package includes
- RGB Wireless Mouse
- Charging Cable
- USB Receiver
- User Manual
Product Features
Light mode switch:
- Long press the switch for 3 seconds to turn off the light, and long press it again for 3 seconds to turn on the light.
- Single press the switch, a total of 21 light modes will show on in cycles.
Mouse Jiggler mode switch:
- Long press DPI for 3 seconds to enter Mouse Jiggler mode(the green light of the scroll wheel will turn on)
- Long press DPI again for 3 seconds to exit Mouse Jiggler mode(the green light of the scroll wheel will turn off
Note: Move the mouse in Mouse Jiggler mode, the mouse can work normally. If the mouse didn’t move in 5 seconds, the mouse will drift automatically (Enter Mouse Jiggler mode)
DPI switching:
Single press DPI to switch cyclically, 800 (red)/ 1200 (blue) / 1600 (green) /
2000 (purple)
Product Specifications
- DPI: 800/1200/1600/2000
- Weight: 8Og
- Battery Capacity: 650mA
- Maximum Working Current: 16mA
- Working Distance: 10m
- Sleep Mode: If the mouse doesn’t move in 90s, it will enter backlight sleep mode. If no movements for over 8 minutes, it will enter deep sleep mode.
- Compatible Systems: Windows XP, Windows 7, Windows 8, Windows 10, Mac OS
2.4G Wireless Mode Connection
LED Indicator Light
- Battery Charging: The red light of the scroll wheel will stay on.
- The Battery Is Full: The red light of the scroll wheel will turn off.
- Battery is Low: RGB backlight red light will lash.
- Mouse Jiggler mode is on: The green light of the scroll wheel will stay on.
- Mouse Jiggler mode is off: The green light of the scroll wheel will turn off.
Note:
- If no movements of the mouse for 90 seconds, the mouse will enter sleep mode, and the mouse backlight wil automatically turn off. You can wake it up by clicking any buttons
- If no movements of the mouse for 8 minutes, the mouse will enter deep sleep mode, and all LED lights will automatically turn off. You can wake it up by clicking any buttons;
- In Mouse Jiggler mode, after the mouse enters deep sleep, the mouse cursor will not stop moving unless you press and hold DPI for 3 seconds to exit Mouse Jiggler mode
- If there is a delay or the mouse backlight turns off during use, please fully charge the mouse.
Frequently asked questions
- What should I do if the mouse sensor has lag problem?
- Please try to turn off the mouse and then turn back on or fully charge it before use.
- What should I do if the mouse does not respond?
- If you turn on the mouse power switch and the mouse indicator light or backlight does not light up, please turn off the mouse and fully charge it.
- I received a defective product. What should I do
- Please contact us through Amazon with your order ID, we will address your issue within 24 hours and arrange you a refund or a replacement.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: This device may not cause harmful interference,
and This device must accept any inteference received, including interference
that may cause undesired operation. Warning: Changes or modifications not
expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures Reorient or relocate the
receiving antenna. Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected. Consult the dealer or an experienced radio/TV
technician for help. RF warning statement The device has been evaluated to
meet general RF exposure requirement. The device can be used in portable
exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>