Newell NL0841 Dual Charger for V-Mount Batteries User Manual
- June 12, 2024
- Newell
Table of Contents
Newell NL0841 Dual Charger for V-Mount Batteries
SAFETY INSTRUCTIONS
- Do not charge batteries that are not intended for this device, as this may damage the battery and lead to leakage and explosion.
- Do not drop the unit or place heavy oblects on it.
- Store in a dry, cool and ventilated place. Do not expose the device to moisture or rain.
- Keep away from heat sources and places of high temperature
- Do not expose to direct sunlight.
- The device can operate in temperature range 0°C – 40°C
- Do not leave it unattended when chargina.
- Remove the batteries from the charger when not in use.
- Keep out of reach of children.
- Slight warming up of the device is normal.
- If you notice smoke or a strange smell coming from the device, immediatels disconnect the power. Do not disassemble. Disassembling the unit will voIc the warranty. If there are probiems win the lamo. onng it to an autonzec service center
PRODUCT DESCRIPTION
- Led – power supply
- Charging State LED
- Battery Online LED
- Discharging State LED
- DC output
- (XLR female connector, 4 DIn Base
- Battery release lever
- charging connector
- Power switch
- AC socket
- Cooling fan
PRODUCT FEATURES
- This charger can charge V-mount batteries with a nominal voltage of 14.4V/14.8V.
- No change required at 100-240V. • Fast charging of one lithium-ion battery, charging of two batteries in succession.
- Equipped with XLR 4P terminal interface, it can be used as a DC power supply for equipment such as cameras.
- A fully charged lithium-ion battery can be used as backup power when there’s no AC power input and supply sequential DC output by XL 4P connector.
USAGE
- Connect the devices to the power source. The AC LED indicator will light up.
- Place the V-Mount lithium-ion battery in the charging channel. The device will start charging.
- When the battery is placed in the charging channel, the Battery LED will light up. Charging state LED lighting in red indicates charging batteries, changing to green at 85% charge, at full charge the light goes out.
- When the cable is connected to the DC port, the charger begins to supplying power and stops charging the batteries.
- With the AC off, the batteries placed in the charger can be used as an additional power source for the DC port. The Discharging state LED will be illuminated.
- When any of the batteries are taken away, the DC power process will stop working. 7. Slight heating of the device is a normal process, therefore. To ensure trouble-free operation of the device, place it in a well-ventilated place.
When used as a charger
-
Install battery on the charger as shown.
-
After connecting the battery, the charger can charge the battery, and the corresponding indicator will light up. If the corresponding indicator is not lit, please check the connection between the charger and the battery.
-
After charging to 85%, the charging indicator, light will turn from red light to green light, and when battery will be fully charged, light will go out.
-
After fully charged, the corresponding indicator light is off and charging is completed.
-
When removing the battery from the charger, firmly press the release lever while lifting the battery straight up
-
For safety, please do not move the charger at will when it is working
When used as with DC output
When power AC is off batteries can be used as backup power and supply
sequential DC output by XLR 4P connector. Connect with XL cable to supply
power for camcorders, etc. Charging function and DC output function cannot be
used at the same time
- While the BP-4CH charger operates as a charger, the DC output function is disabled. While the DC output is in operation, charging is disabled.
- Please make sure to check the power consumption of the connected device prior to using the BP-4CH DC output before use.
Operation Procedure
Tilt the loader to the side and tilt the support until it locks into place
.
AC Power Cable connection
Connect AC cable with BP-4CH charger and make it plugged in, then turn the
switch to “I” position as shown.
- Please place the charger at ventilate location, do not cover the window of radiator fan.
LED State Indication
SPECIFICATION
The manufacturer reserves the right to change the information contained in this manual without prior notice.
WASTE MANAGEMENT
The crossed-out trashcan symbol means that waste electrical and electronic,
batteries and packagings must not be placed with other household waste. They
must be handed over to a separate waste collection system.
WARRANTY
Newell products are covered by a 40-month manufacturer’s warranty.
Made in China