Newell FT-650 FX Vividha Effect RGB LED Lamp Instruction Manual
- May 15, 2024
- Newell
Table of Contents
LED Lamp
RGB Vividha Effect 
SAFETY INSTRUCTIONS
Before using the product, please read the following instruction manual carefully and keep it for future reference. When transferring the product to a third party, itis advisable to include the instructions.
- The lamp is a precision device. Do not drop, hit, crush or expose to any shock.
- The unit is not dustproof or waterproof. Store in a dry, cool and ventilated place. Do not expose to water or other sources of moisture.
- Do not use near flammable materials and solvents.
- Do not use the lamp too close to objects. Do not cover the ventilation holes. Do not insert metal parts into the lamp. Do not touch the electrical parts with conductive materials.
- The lamp can operate in a temperature range of 0°C – 35°C.
- The lamp will heat up slightly, but it is normal.
- Do not stare directly at the LED panel that is turned on, it may cause eye damage.
- Do not use the LED outside in direct sunlight for a long time.
- Disconnect the power supply for storage or transportation.
- Allow the unit to cool down before placing it in the package. For use by adults.
- If you notice smoke or a strange smell coming from the device, immediately disconnect the power. Do not disassemble. Disassembling the unit will void the warranty. If there areproblems with the lamp, bring it to an authorized service center.
Maintenance
Use a dry and soft cloth to clean the unit. Do not clean with water. A little
neutral detergent on the cloth to remove stubborn dirt. Do not use strong
detergents such as thinner, benzine or alcohol as they may damage the
protective coatings.
PRODUCT DESCRIPTION
- Power switch
- AC adapter port
- DMX port
- Function buttons
- Battery compartment
- Battery release button
- Display
- Locking screw for tilt angle
- 16 hole for light stand
- Fixing screw for light stand
- Barndoors
- LEDs
- Magnetic holders for diffuser panel
- Swivel Frame
- Diffusion panel
INSTALLATION AND USAGE
Power on / off
-
Use battery power
Insert two NP-F batteries into the battery compartment of the photography light in the correct direction. Slide the power switch (1) to ‘DC’ position. The LCD screen display lights up and the photography light will turn on. When removing the battery, please press and hold the battery release button [6] first to avoid damaging the battery compartment. -
Use external adapter for power supply
Plug the supplied AC adapter cable into the AC adapter port[2] and screw the cap shut. Slide the power switch [1] to ‘AC’ to switch on the LED light. -
Power off
Slide the power switch (1) to ‘OFF’ position
Function adjustment settings
1. Control panel
| Button | Operation |
|---|---|
| SET | Press SET button to switch to SETUP in terface |
| MODE | Repeatedly press to select CCT mode, HSI mode, effect mode and Pixel Fx |
mode.
| Press UP or down button, to change function options.
| Rotate Regulator to select language select effects or change parameter.
2. Function description
« Set language
The default factory setting is English. Press SET button , then press to ENG.
Using Rotate Regulator choose desired language. « SetID
Press SET button to get access to SETUP interface.
Press A button to locate to ID. Rotate regulator to select ID value 001-200.
You can set every light fixture with a unique ID.
– DMX Control
- Use DMX adapter cable (not included) to establish the connection between light fixtur and DMX console.
- To prevents interference the DMX output of the last light fixture should be connected with a DMX terminator (not included).
Set DMX
This light fixture supports DMX 512.
First, connect light fixture with DMX console. Then, set DMX value on the
light fixture. Press A button to select between DMX MODE, DMX ADDRESS and DMX
PIXEL. Rotate regulator to adjust the value of DMX mode, DMX address and DMX
pixel.
DMX address range: 001-512
DMX PIXEL value: 1or 4
When pixel 1is selected, one color is displayed on the entire light fixture.
When pixel 4 is selected, a total of 4 colors will be displayed on the entire
light fixture.
If you select DMX mode RGBWY, each pixel will use 5 DMX addresses
If you select DMX mode RGB, each pixel will use 3 DMX addresses.
If you select DMX mode WY, each pixel will use 2 DMX addresses. 
After well connecting light fixture with DMX console, and after
finishing the setting of DMX mode, DMX address and DMX pixel, press SET button
to active DMX function. DMX Display shows as follows: DMX control and APP
cannot be used at the same time. DMX will be used first.
SET CCT Mode
Press MODE button to select CCT Mode. Press button to select from DIM, CCT,
G/M.
Rotate regulator to adjust the values.
DIM range: 000% -100% CCT range: 2700K-10000K G/M range: -100 – +100 SET HSI
Mode
Press MODE button to select HS| Mode. Press button to select from DIM, HUE,
SAT.
Rotate regulator to adjust the value.
DIM range: 000% -100% HUE range: 000-360 SAT: 000-100 Special Effect Mode
There are 15 special effect modes, including HUE LOOP, CCT LOOP, INT LOOP,
FLASH, PULSE, STORM, POLICE CAR, TV, PAPARAZZI, FIRE, DISCO, BAD BULB,
FIREWORKS, EXPLOSION and WELDING. 
Set Special
Effect
Press MODE button to select EFFECT Mode. Rotate knob to select desired effect.
Press button to change function options.
Rotate knob to change the value of every
function option.
Pixel Effect Mode
There are 12 pixel effect modes, including HUE LOOP, CCT LOOP, INT LOOP,
MULTICOLOR, FADE, PROCESS, SCROLL,FIRE, RAINBOW,DRIVING, POLICE CAR,
AMBULANCE.
Note:
PROCESS, FIRE and DRIVING will only be displayed on the light fixture via the
control of APP.
The setting of pixel effects mode is the same as the special effect
mode.
MOBILE APP
- Download the “LIGHT LINK” app directly from the App Store or the Google Play Store.
- Switch on FT-650RX LED light panel.
- Follow the instructions in the app.
Using smartphone to control LED light:
- Set the light number and ID to connect to the mobile app:
- Hold down the MODE key for 3 seconds
- Set NO value in the range of 1-99
- Press the MODE button
- SetID value in range of 1-200
- Save the set values (you will need them for the mobile application)
- Hold the MODE button for 3 seconds to save the settings the dial to change the brightness from 0 to 100.
SET CONTENT
- RGB LED light panel with barndoors – 1 pc
- Diffusion panel – 1 pc
- AC Adapter – 1 pc
- Soft padded carrying bag – 1 pc
- Uder manual – 1 pc s wN S
SPECIFICATION
WASTE MANAGEMENT
**** The crossed-out trashcan symbol means that waste electrical and electronic equipment, batteries and packagings must not be placed with other household waste. They must be handed over to a separate waste collection system.
WARRANTY
Newell products are covered by a 40-month manufacturer’s warranty.
“The manufacture reserves the right to change the information contained i tis
manualwithout prior nofice
| Model | VIVIDHA EFFECT (FT- 650 FX) |
|---|---|
| LED quantity | 144 PCS 2700 K, 144 PCS 6500 K, 288 PCS RGB |
| MODE | CCT, Hsl |
| Power Output | 60 W |
| Illumination | 2240 lux / m @5500 K |
2200 lux / m @7500 K
1950 lux / m @10000 K
7000 lux /0.5 m @2700 K
8050 lux /0.5 m @5500 K
7750 lux /0.5 m @7500 K
6750 lux / 0.5 m @10000 K
Color Temperature| 2700-10000 K
RGB| 000- 360
CRI@5500K| >96 %
DIM range| 0-100%
AC power supply| 1pc power adapter
Input: AC100-240 V2.0 A
Max 50 / 60 Hz
Output: 15.0 v5.0 A75 W
DC power supply| 2 pcs NP-F battery (not included)
Product weight| 700g
Product size| 385x375x6cm
Housing Material| Aluminum alloy
Made in china
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>