Newell NL4076 Sunny LED Light for smartphone Instruction Manual

Newell NL4076 Sunny LED Light for smartphone

SAFETY INSTRUCTIONS
Before using the product, please read the following instruction manual carefully and keep it for future reference. When transferring the product to a third party, it is advisable to include the instructions.

1. The lamp is a precision device. Do not drop, hit, crush or expose to any shock.
2. The unit is not dustproof or waterproof. Store in a dry, cool and ventilated place.
3. Do not expose to water or other sources of moisture.
4. Do not use flammable materials and solvents.
5. Do not insert metal parts into the lamp. Do not touch the electrical parts with conductive materials.
6. The lamp can operate in a temperature range of 0°C – 40°C.
7. The lamp will heat up slightly, but it is normal.
8. Do not stare directly at the LED panel that is turned on, it may cause eye damage.
9. Do not use the LED outside in direct sunlight for a long time.
10. Do not lift the camera while holding the lamp handle.
11. Allow the unit to cool down before placing it in the package.
12. For use by adults.
13. If you notice smoke or a strange smell coming from the device, immediately disconnect the power.
14. Do not disassemble. Disassembling the unit will void the warranty. If there are problems with the lamp, bring it to an authorized service centre.

Important!
When not in use for a long time, press engage it every 3 months to ensure the durability of the battery.

Maintenance

Use a dry and soft cloth to clean the unit. Do not clean with water. A little neutral detergent on the cloth to remove stubborn dirt. Do not use strong detergents such as thinner, benzine or alcohol as they may damage the protective coatings.

PRODUCT DESCRIPTION

1. Decrease the brightness button
2. levels adjustment)
3. Increase brightness button
4. levels adjustment)
5. Switch button / Light mode toggle
6. Charging port
7. 1/4″ Screw interface

USAGE

1. ON / OFF button. Long press the switch for 1.5 seconds to turn it on and long press again for 1.5 seconds to turn it off.
2. Light mode. After the fill light is turned on, lightly press the switch to change the light colour. The lamp has three light modes: cold yellow light, warm light, and white light.
3. Brightness adjustment. When the light is on, lightly press “+” to enhance the brightness, and lightly press “-” to weaken the brightness. There are 5 levels of brightness.
4. Memory function. The product has added a memory function, it will still retain the same lighting mode that was used last time.
5. Charging time is about 2 hours. At maximum brightness, the light can be used for about 2.2 hours.

INSTALLATION

Clamp Mounting
Slide the bottom part of the clip into the hole in the lamp to use it.

Cold Shoe Mounting
Point the cold shoe adapter at the screw hole and tighten the screw to secure it.

MAGNET RING INSTALLATION

1. Remove the protective film on the magnet ring.
2. Paste the magnet ring onto the back surface of the phone or phone cases.
3. The surface of the magnet attracts the magnetic surface of the lamp.

Note
 iPhone 12 series and newer models work directly with the magnetic surface of the light It is not necessary to use the magnetic ring included in the kit.

SPECIFICATION

SET CONTENT

• Magnetic LED light – 1 pcs
• Clip – 1 pcs
• Magnet ring – 1 pcs
• USB charging cable – 1 pcs
• 1/4″ Screw connector – 1 pcs
• User manual – 1 pcs

WASTE MANAGEMENT
The crossed-out trashcan symbol means that waste electrical and electronic equipment, batteries and packaging must not be placed with other household waste. They must be handed over to a separate waste collection system.

WARRANTY
Newell products are covered by a 40-month manufacturer’s warranty . The manufacturer reserves the right to change the information contained in this manual without prior notice. Do CE Made in Chin, China hergel! Hecho en China, Fabricato in Cina,

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>