NORDIC Play BMW M6 GT3 Electric Car User Manual

NORDIC Play BMW M6 GT3 Electric Car

Product Information

Product Usage Instructions

Warning:

• The vehicle should only be used on flat surfaces and not on roads, sidewalks, hills, or sand.
• Do not overload the vehicle. Pay attention to the maximum weight limits. Typical maximum total weight is 25 – 35 kg. Please check for your specific model.
• Only adults may charge the battery. Children using the vehicle should always be supervised by a responsible adult.
• Do not charge the vehicle’s circuit.
• Do not drive in water or other fluids.
• Stop the vehicle when it is approaching an obstacle, turn away from the obstacle and drive somewhere else.
• Please charge the battery when the vehicle starts to drive slowly, otherwise the battery’s lifespan can be shortened.
• Please charge the battery fully before the battery is stored for longer periods without use.
• Charge the battery every three months to extend the battery’s lifespan.
• Do not drive during rain. Battery, charger, electrical cables, outlets, and other parts should periodically be checked. If damages are discovered, the vehicle may not be used until these are fixed.
• The charger should be checked for damages on cord, plug, and other parts periodically. If there are damages, the charger may not be used until the damage is fixed. Vehicle with a battery may not be used by children under 3 years of age.
• Push/foot-to-floor vehicles without a battery can be used from 1 year of age.
• The vehicle may only be used with the recommended charger.
• The charger is not a toy.
• Only clean with a damp cloth.
• Check that all parts are undamaged. If not, repair or change these.
• It is a good idea to use safety equipment, depending on the vehicle.
• Worn out batteries should be removed/changed from the vehicle.
• The battery should be removed before the vehicle is disposed of.

Declaration of conformity:

This product is in accordance with EU directive 2014/53 / EU.

Warning: For your child’s safety, pay attention to the following

• Only adults may assemble the product.
• Small parts and plastic parts should be kept away from the child to avoid risk of suffocation.
• Children may not touch or open the battery holder.
• Adult supervision is required.
• Vehicles with a battery may not be used by children under 3 years of age.
• Push/foot-to-floor vehicles without battery can be used from 1 year of age.
• Use the vehicle with caution, since driving skills are required to avoid falls or crashes that can result in injuries to the user or third party.
• May not be used in traffic. Only use the vehicle on private property.
• Only drive on flat surfaces away from other vehicles and obstacles.
• Avoid sharp bumps and sudden changes of the surface.
• Avoid roads and surfaces with water, sand, gravel, dirt, leaves, and other debris.
• Wet weather can reduce the traction, brake effect, and visibility.
• Do not drive when it is dark.

General safety rules for NORDIC PLAY products

Warning:

• The vehicle may not be used on roads, sidewalks, in hills or sand.
• The vehicle should only be used on flat surfaces.
• Do not overload the vehicle. Pay attention to the maximum weight limits. Typical maximum total weight is 25 – 35 kg. Please check for your specific model.
• Only adults may charge the battery.
• Children using the vehicle should always be supervised by a responsible adult.
• Do not charge the vehicle’s circuit.
• Do not drive in water or other fluids.
• Stop the vehicle when it is approaching an obstacle, turn away from the obstacle and drive somewhere else.
• Please charge the battery when the vehicle starts to drive slowly, otherwise the battery’s lifespan can be shortened.
• Please charge the battery fully before the battery is stored for longer periods without use. Charge the battery every three months to extend the battery’s lifespan.
• Do not drive during rain.
• Battery, charger, electrical cables, outlets and other parts should periodically be checked. If damages are discovered, the vehicle may not be used until these are fixed.
• The charger should be checked for damages on cord, plug and other parts periodically. If there are damages, the charger may not be used until the damage is fixed.
• Vehicle with a battery may not be used by children under 3 years of age.
• Push/foot-to-floor vehicles without a battery can be used from 1 year of age.
• The vehicle may only be used with the recommended charger.
• The charger is not a toy.
• Only clean with a damp cloth.
• Check that all parts are undamaged. If not, repair or change these.
• It is a good idea to use safety equipment, depending on the vehicle.
• Worn out batteries should be removed/changed from the vehicle.
• The battery should be removed before the vehicle is disposed of.
• Declaration of conformity: This product is in accordance with EU directive 2014/53 / EU.

Warning: For your child’s safety, pay attention to the following:

• Only adults may assemble the product.
• Small parts and plastic parts should be kept away from the child to avoid risk of suffocation.
• Children may not touch or open the battery holder.
• Adult supervision is required.
• Vehicles with a battery may not be used by children under 3 years of age.
• Push/foot-to-floor vehicles without battery can be used from 1 year of age.
• Use the vehicle with caution, since driving skills are required to avoid falls or crashes that can result in injuries to the user or third party.
• Instructions on how the vehicle is used should be given to the child before use – especially for the braking system.
• May not be used in traffic. Only use the vehicle on private property.
• Only drive on flat surfaces away from other vehicles and obstacles.
• Avoid sharp bumps and sudden changes of the surface.
• Avoid roads and surfaces with water, sand, gravel, dirt, leaves and other debris.
• Wet weather can reduce the traction, brake effect and visibility.
• Do not drive when it is dark.
• Avoid excessive speed in conjunction with downhill driving.
• Watch out for pedestrians.
• Check and tighten all screws before every drive. Do not allow two or more children to use the vehicle at once.
• Do not use the vehicle if it has damages.
• Change damaged parts immediately

1. Insert 220V/12V charger cable’s connector to the vehicle.
2. Insert actual 220V/12V charger unit to your 220V power outlet. The battery will start charging.
3. Detach after 8-12 hours

IMPORTANT NOTE: When shifting (forward/backward), please make sure the vehicle is completely stopped, otherwise it will damage the gear box and motor.

Forward:

1. Press the ”Forward/backward switch” to the ”Forward” position.
2. Press the ”Foot pedal”, the vehicle drives forward.

Stop:

1. The vehicle will brake automatically, when foot is lifted from the ”foot-pedal”.

Back Up:

1. Press the ”Forward/backward switch” to the ”Backward” position.
2. Press the ”Foot pedal”, the vehicle will back up.

Loosen the screw from the back of the seat seat, take away the seat. Then connect the battery line red wire to the red terminal of the battery and finally then connect black wire to black battery terminal. Never connect wires into the uncorrect battery terminals. After the connections, please assemble the seat back to the original place and tighten the screw.

Battery replacement and fuse
The battery is equipped with a thermal fuse which blows if the motor, battery or electrical circuit is overloaded. The vehicle must then be switched off for at least 5 minutes, after which the fuse will restore itself. If the product does not work, the fuse may therefore be the problem. To avoid this, read the following points:

• Do not overload the vehicle.
• Do not pull anything behind the vehicle.
• Do not drive up steep hills.
• Do not run into motionless objects that cause the wheels to spin.
• Do not drive at extreme temperatures.
• Make sure the product does not come into contact with liquids.
• Do not touch the electrical circuit.

As the battery gets older it will start to lose some of its capacity. Depending on the conditions, it can last anywhere from 1 – 3 years. If the battery needs a replacement, follow these steps:

1. Loosen the crew and remove the seat.
2. Disconnect the cables from the battery terminals.
3. Remove the battery cover.
4. Carefully lift the battery out of the vehicle. Depending on the condition of the battery (leakage or similar), safety equipment may be required. Do not lift the battery from its wires but from the battery itself.
5. Put the battery in a plastic bag and dispose it responsibly. NEVER put the battery to general waste.
6. Insert the new battery into the vehicle.
7. Reconnect the cables to the new battery. Red wire to red terminal (+) and black wire to black terminal (-) of the battery.
8. Slide the seat into place. Tighten the screw.

To protect the environment, batteries and electrical equipment must be disposed separately from household waste. Contact the municipality for the nearest collection point.

overload the vehicle.
Battery connector or wires are loose| Check that the battery connectors and

wires are firmly connected.

Battery is dead| Battery lasts 1-3 years. Replace battery and recycle the old battery responsibly.
Electrical system is damaged| Contact your distributor please.
Motor is damaged| Contact your distributor please.
Vehicle does not run very long| Battery is not properly charged.| Check that the battery connectors are firmly plugged into each other when recharging. Recharge battery again.
Battery is old| Battery lasts 1-3 years. Replace battery and recycle the old battery responsibly.
Vehicle runs sluggishly| Battery low on power| Check that the battery connectors are firmly plugged into each other when recharging. Recharge battery again.
Battery is old| Battery lasts 1-3 years. Replace battery and recycle the old battery responsibly.
Vehicle is overload| Reduce weight on vehicle. Maximum user weight is 25 kgs.
Vehicle is being used in unsuit- able conditions| Use the vehicle on flat, even surfaces.
Vehicle needs a push to go forward| Poor contact of wires or connectors| Check that the battery connectors are firmly plugged into each other when recharging. Recharge battery again.
“Dead Spot” on motor| A dead spot means the electric power is not being delivered to the terminal con nection and the vehicle needs re- pair. Contact your distributor please.
Difficult shifting from forward to

reverse or vice-versa

| Attempting to shift while the vehicle is motion| Always completely stop the vehicle before shifting.
Loud grinding or clicking noises coming from motor or gear box| Motor or gears are damaged| Contact your distributor please.
Battery will not recharge| Battery connector or adapter connector is loose| Check that the battery connectors are firmly plugged into each other when recharging. Recharge battery again.
Charger not plugged in| Check that the battery charger is plugged into a working wall outlet.
Charger is not working| Contact your distributor please.
Charger feels warm when recharging| This is normal and not a cause for concern|

Completely read through this manual and the troubleshooting guide table before calling. If you still need help resolving the problem Contact your distributor please.

Maintenance

• Check all screws periodically and tighten as needed.
• Check the vehicle’s plastic components frequently for damage.
• The mechanical parts of the vehicle can be lubricated with oil if necessary.
• Store the product indoors to protect it from the weather.
• Keep product away from hot items such as stove and the likes.
• Do not clean the product with a garden hose and do not use soap. A dry or moist cloth is enough.
• Do not drive in rain, snow, sand and gravel as this may damage the product.
• If the product is not to be used for an extended period, recharge the battery and then disconnect all cables

Installation and Operating Instructions

Please read the operating instructions carefully before use The BMW logo and the BMW wordmark are trademarks of BMW AG and are used under license.

Charger:

| DC 15V / 800 mA| Charging time:| 8 – 12 hours
Input: AC 100-240V|  |
 |  |

Our products are suitable for
ASTM F963; GB6675,GB19865; EN71 and EN62115 standard.

Contents:

1. Product specifications and parameters
2. Components list
3. Assembly diagram
4. Installation and replacement of remote control batteries
5. Function and operation
6. Battery and charger operation guide

Product specifications and parameters

1. This product is suitable for the children of 3-6 years old, and should be used under adult supervision!
2. Product dimensions: 130.7 × 69.1 × 48.8CM
3. Product maximum load weight: 30 kg
4. Product charger: input AC 100-240V (50 / 60Hz), Output (See charger parameters of the product)
5. Charging battery: (1 battery) it can provide about 200 cycles of charging and discharging
6. Remote control and manual switching functions, 2.4G one-to-one remote control function
7. DC power supply of the remote controller: (The battery of this product is not included)
8. Product operating ambient temperature: 0-40°

Operation of overcurrent protector

1. The overcurrent protector is installed under the seat. You can see it by twisting the seat screw off (As shown in the figure) and taking the seat away.

2. When the car is overloaded, the overcurrent protector automatically disconnects the circuit
   (For protecting the circuit); when the circuit fault is removed, the overcurrent protector automatically connects the circuit.

3. When the battery has power and the car can not run, please check whether the circuit of the car has an open circuit or short circuit.

Components list

**

**

Assembly Diagram

Installation of front axle frame connecting-rod and wheel

• A. Install the front axle frame connecting-rod (part 11) at the assigned location, and then tighten it with the front axle frame connecting-rod screw (part 14) and locknut (part 19). (The tightening degree shall be based on the flexible swing direction.)
• B. Use the thumb to press the wheels (part 6) center button, and then put them into the front axle in sequence.
• C. Rotate the motor gearbox upwards according to the direction indicated by the arrow until the motor gearbox hole aligns with the car body axle hole, and then insert the rear axle (part 13) into the assigned location of the car body.
• D. Use the thumb to press the center button of the driving wheels (part 7) to put them into the rear wheel axle in sequence.

When the wheels are installed, press the center button of the wheels, insert the wheels into the front axle and fix them; press the center button of the wheels to pull out the wheels from the axle so as to remove the wheels.

Installation of J-shaped stick
Insert the J-shaped iron hook (part 12) into the designated gearbox at the front of the car. Then tighten with the hole specified by the steering gear box screw (part 17).

Install the rear-view mirror

Open the door, install the inverted mirror (part 4) in the specified position, and tighten the inverted mirror with screws (part 18) as shown.

Installation of steering wheel and hand shank

1. Plug the wire plug of the steering wheel into the wire plug from the car body hole correspondingly, and then put the connected plugs into the car body hole.
2. Install the steering wheel (part 3) on the J-shaped iron hook, and tighten with the steering wheel screw (part 15) and the steering wheel anti-loose nut (part 20); then insert the handle (part 5) into the designated position and press down firmly to make it reliably connected.

Installation of power supply

Insert plug into the circuit board to its bottom.

Install the seat and seat back.

1. After the power supply is installation, put the seat (part 8) into the assigned location of the car body, and fix it with the screw (part 16).
2. Put the seat backrest (part 9) into the assigned location of the car body as shown in the figure, and tighten it with the seat backrest screw (part 16).

Install the windshield and the empennage

1. Install the windshield (part 2) at the specified position on the front of the car. Before the installation, fix the position of each buckle and press until it is fastened.
2. Insert the rear wing (part 10) at the direction shown by the arrow, and insert the corresponding buckle, and press the buckle firmly until it is fasten

Open the car door

Press on-off button outside the vehicle door sheet, then pull the vehicle door outside and open the door.

Installation and replacement of remote control batteries

Unscrew the battery cover screws of the remote control (part 22), open the battery cover, find the positive and negative poles, put 2 AAA batteries into the battery compartment, close the battery cover and fix it with screws.

Function and Operation

Main functions:

1. There are remote controllable and pedal switch buttons.
2. Rear drive: Power motor gearbox provides powerful ”front or rear” power.
3. Forward / backward function: There are three forward speed level, neutral gear and reverse gear on right side of the panel (each gear has its own LED display)
4. Foot switch function: Press the foot switch button, when the handle is in forward or backward position, step down the foot switch to move the car forward or backward, and release the foot switch to stop the car.
5. Charging protection function: All functions needing to be powered by the battery will fail when the battery is being charged.
6. Forward / backward brake function: It has relay brake function whether it is moving forward or moving backward or parking.
7. Turn the auxiliary pull wheel at the bottom of the car out, and turn the pull handle at the front bottom of the car out to pull it away.

Normal operation:

1. Foot switch mode
   • A. Press the main power switch button
   • B. Press the foot pedal button
   • C. Select the forward / reverse direction
   • D. Select the speed gear
   • E. Step on the pedal to start
2. Remote control code-matching operation
   • A. Press the main power switch button to turn it on (Coding will be valid within two minutes after powering on)
   • B. Simultaneously keep pressing the speed change button and sudden brake button of the remote control for 5 seconds; if the lamp of first gear, second gear and third gear twinkles, it will indicate that the code-matching action is transmitted; it will indicate that the codes are matched successfully until the lamp is on and stops twinkling; when the code-matching action is received, the front wheel will rotate leftwards for 1s and rightwards for 1s.
3. Remote control function
   • A. Forward / Backward button
   • B. Left/right movement button
   • C. Sudden brake button
   • D. Speed change button E. It will enter the sleep state if no operation occurs within 1 min. You can press any button to reawaken it.

2.4G remote control

Functions on the central control board:

One-button start button:

1. Press this button to turn on the main power, and the system is in standby mode, and the trumpet gives a sound of engine. Red light of one button start button and green light of foot switch mode button will be on, displaying “00.00” with ”V”, and the normal voltage will be displayed after the engine sound; then the English prompt sound of ”music player” music is played, and the music button will be invalid until the prompt sound is over.
2. After pressing this button for 2 seconds, the main power will be cut off and the system will be shut down.

Music button:
Under MUSIC play mode, press this button to play a song, and the green light
of this button is on; press this button again to play the next song; there are 2 music buttons, each button will play 3 songs repeatedly.

Previous\Volume – Button:
In MUSIC USB BT mode: short press this button, the green light of this
button will be on for a short period of time and it will change to the previous
music; long press this button for 2 seconds without release, the green light of this button will be on, the volume will be decremented, the volume value on display will decrease from U30 to U00. Each time of starting, the default volume value will be U25.

Next music \ Volume+ button:

1. In MUSIC USB BT mode: short press this button, the green light of this button will be on for a short period of time and it will change to the next music; long press this button for 2 seconds without releasing, the green light of this button will be on; the volume will increase and the volume value on the display will be displayed incrementally from U00 to U30.
2. Each time of starting, the default volume value will be U25.

Light / fan button:
The start button is in “off” mode by default, press once to turn on the light, and the green light will be on; press again to turn on the fan, and the light will be off; press the button for the third time to turn on both the light and fan; press the button for the fourth time to turn off both the light and fan, and at the same time, the green light of this button will be off.

Foot switch button:

1. It is by default in the foot switch mode, and the green light of this button will be on; then turn on the gear, and step on the foot switch to start and loose the foot switch to slow down the car; press the remote control button to stop the car forcefully. (The car can’t be started by foot switch when it is stopped by the remote controller!)
2. Safety protection function: Before starting the car by stepping on the accelerator or switching from the remote control mode to the footswitch mode, you must first loosen the accelerator pedal and then step on it.

Remote control button:
When this button is pressed, the system will switch to the remote control mode, and the green light will be on, then the remote controller can be used to drive the car.(At this time, stepping on the accelerator pedal is unavailable!)

Mode switch button:

1. It is by default the built-in music play mode, and there is ”music player” English prompt sound, and the display ”MUSIC” will be always on;
2. Press this button and switch to USB mode, and there is ”USB mode” English prompt, and ”USB” on display will flash (Flash when USB is not connected, and it will be always on when it is connected to USB);
3. Press this button again and switch to BT Bluetooth mode, and there is ”bluetooth mode” English prompt, ”BT” on display will flash (Flash when Bluetooth is not connected, and it will be always on when Bluetooth is connected);
4. Press this button again and switch back to the built-in music playback mode.
   (It will be Press USB mode Press BT mode Press Music mode Loop) as such

Display function

Four digits display:

1. The middle four digits display the voltage of the battery in real time; it will display the volume change in adjusting the volume (U00-U30); which song (0001-9999) in USB
   music will be displayed during USB playback.

2. The function icons on both sides of the display are “MUSIC, USB, BT, V, ►, ꞊ ”, and the mode or state in which it lies will be displayed by its corresponding icon.

Bluetooth playback function:

1. In Bluetooth mode, after connecting Bluetooth, the “BT” on display will be always on, and then the audio file in the Bluetooth device can be played.
2. When Bluetooth is disconnected, there is a “dingding” prompt tone, and “BT” on display will flash.
3. Name of Bluetooth: CHILOKBO

USB playback function:
In USB mode, after connecting USB, the “USB” on the display will be always on, and then the audio file in USB can be played.

Steering wheel button:
The middle is the horn sound button, which will be sounded in any audio playback mode; press and hold this button, the horn will sound continuously.

Sleep function:
The system will enter sleep mode when it is without driving for 30 min, and the central control board will automatically shut down, and all functions will turn off!

Low voltage protection function:
When the voltage is as low as 8V, the central control board will automatically power off and the car will stop automatically. Please charge as soon as possible!

Charging and power-off function:
When charging the car, the central control board will automatically power off. All functions will be turned off, and the car cannot be started!

Battery and Charger Operating Guide
The charging socket is located at the lower part of the car seat.

Imported by /
NSH NORDIC A/S
Virkefeltet 4
DK-8740 Braedstrup
Made in China / produceret i Kina

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>