NORDIC PLay 805-757 Electric Motorcycle Instruction Manual

NORDIC PLay 805-757 Electric Motorcycle

Product Information

• Product Name: NORDIC PLAY Vehicle
• Dimensions: 54 x 33 x 82 cm
• Art. No.: 805-757
• EAN: 5705858709208
• Importer: NSH NORDIC A/S
• Imported from: China

Product Usage Instructions

1. The vehicle should only be used on flat surfaces.
2. Do not use the vehicle on roads, sidewalks, hills, or sand.
3. Do not overload the vehicle. Pay attention to the maximum weight limits specified for your specific model (typically 25-35 kg).
4. Only adults should charge the battery.
5. Children using the vehicle should always be supervised by a responsible adult.
6. Avoid driving the vehicle in water or other fluids.
7. If the vehicle is approaching an obstacle, stop it, turn away from the obstacle, and drive in a different direction.
8. Charge the battery when the vehicle starts to drive slowly to prevent shortening its lifespan.
9. Before storing the vehicle for longer periods without use, fully charge the battery.
10. To extend the battery’s lifespan, charge it every three months.
11. Avoid driving the vehicle during rain.
12. Regularly check the battery, charger, electrical cables, outlets, and other parts for damages. Do not use the vehicle if damages are discovered until they are fixed.
13. Periodically check the charger for damages on the cord, plug, and other parts. Do not use the charger if there are damages until they are fixed.
14. Children under 3 years of age should not use the vehicle with a battery. Push/foot-to-floor vehicles without a battery can be used from 1 year of age.
15. Use the recommended charger for the vehicle. The charger is not a toy.
16. Clean the vehicle only with a damp cloth.
17. Check all parts for damages. Repair or replace any damaged parts.
18. Consider using safety equipment depending on the vehicle.
19. Remove/change worn out batteries from the vehicle.
20. Remove the battery before disposing of the vehicle.
21. Declaration of Conformity: This product complies with EU directive 2014/53/EU.
22. For child’s safety, only adults should assemble the product.
23. Keep small parts and plastic parts away from children to avoid suffocation risks.
24. Children should not touch or open the battery holder.
25. Adult supervision is required.
26. Children under 3 years of age should not use vehicles with a battery. Push/foot-to-floor vehicles without a battery can be used from 1 year of age.
27. Use the vehicle with caution to avoid falls or crashes that may cause injuries to the user or third parties.
28. The vehicle should not be used in traffic. Only use it on private property.
29. Drive only on flat surfaces away from other vehicles and obstacles.
30. Avoid sharp bumps and sudden changes in the surface.
31. Avoid driving on roads and surfaces with water, sand, gravel, dirt, leaves, and other debris.
32. Wet weather can reduce traction, brake effect, and visibility.
33. Do not drive when it is dark.
34. Avoid excessive speed during downhill driving.

General safety rules

General safety rules for NORDIC PLAY products

Warning:

• The vehicle may not be used on roads, sidewalks, in hills or sand.
• The vehicle should only be used on flat surfaces.
• Do not overload the vehicle. Pay attention to the maximum weight limits. Typical maximum total weight is 25 – 35 kg. Please check for your specific model.
• Only adults may charge the battery.
• Children using the vehicle should always be supervised by a responsible adult.
• Do not charge the vehicle’s circuit.
• Do not drive in water or other fluids.
• Stop the vehicle when it is approaching an obstacle, turn away from the obstacle and drive somewhere else.
• Please charge the battery when the vehicle starts to drive slowly, otherwise the battery’s lifespan can be shortened.
• Please charge the battery fully before the battery is stored for longer periods without use. Charge the battery every three months to extend the battery’s lifespan.
• Do not drive during rain.
• Battery, charger, electrical cables, outlets and other parts should periodically be checked. If damages are discovered, the vehicle may not be used until these are fixed.
• The charger should be checked for damages on cord, plug and other parts periodically. If there are damages, the charger may not be used until the damage is fixed.
• Vehicle with a battery may not be used by children under 3 years of age.
• Push/foot-to-floor vehicles without a battery can be used from 1 year of age.
• The vehicle may only be used with the recommended charger.
• The charger is not a toy.
• Only clean with a damp cloth.
• Check that all parts are undamaged. If not, repair or change these.
• It is a good idea to use safety equipment, depending on the vehicle.
• Worn out batteries should be removed/changed from the vehicle.
• The battery should be removed before the vehicle is disposed of.
• Declaration of conformity: This product is in accordance with EU directive 2014/53 / EU.

Warning:
For your child’s safety, pay attention to the following:

• Only adults may assemble the product.
• Small parts and plastic parts should be kept away from the child to avoid risk of suffocation.
• Children may not touch or open the battery holder.
• Adult supervision is required.
• Vehicles with a battery may not be used by children under 3 years of age.
• Push/foot-to-floor vehicles without battery can be used from 1 year of age.
• Use the vehicle with caution, since driving skills are required to avoid falls or crashes that can result in injuries to the user or third party.
• Instructions on how the vehicle is used should be given to the child before use – especially for the braking system.
• May not be used in traffic. Only use the vehicle on private property.
• Only drive on flat surfaces away from other vehicles and obstacles.

General safety rules for NORDIC PLAY products

• Avoid sharp bumps and sudden changes of the surface.
• Avoid roads and surfaces with water, sand, gravel, dirt, leaves and other debris.
• Wet weather can reduce the traction, brake effect and visibility.
• Do not drive when it is dark.
• Avoid excessive speed in conjunction with downhill driving.
• Watch out for pedestrians.
• Check and tighten all screws before every drive. Do not allow two or more children to use the vehicle at once.
• Do not use the vehicle if it has damages.
• Change damaged parts immediately.

1. Insert 220V/12V charger cable’s connector to the vehicle.
2. Insert actual 220V/12V charger unit to your 220V power outlet. The battery will start charging.
3. Detach after 8-12 hours

IMPORTANT NOTE:
When shifting (forward/backward), please make sure the vehicle is completely stopped, otherwise it will damage the gear box and motor.

Forward:

1. Press the ”Forward/backward switch” to the ”Forward” position.
2. Press the ”Foot pedal”, the vehicle drives forward.

Stop:

1. The vehicle will brake automatically when foot is lifted from the ” foot pedal”.

Back-Up:

1. Press the ”Forward/backward switch” to the ”Backward” position.
2. Press the ”Foot pedal”, the vehicle will back up.

Loosen the screw from the back of the seat, and take away the seat. Then connect the battery line red wire to the red terminal of the battery and finally then connect the black wire to the black battery terminal. Never connect wires to the incorrect battery terminals. After the connections, please assemble the seat back to the original place and tighten the screw.

Battery replacement and fuse
The battery is equipped with a thermal fuse that blows if the motor, battery or electrical circuit is overloaded. The vehicle must then be switched off for at least 5 minutes, after which the fuse will restore itself. If the product does not work, the fuse may therefore be the problem. To avoid this, read the following points:

• Do not overload the vehicle.
• Do not pull anything behind the vehicle.
• Do not drive up steep hills.
• Do not run into motionless objects that cause the wheels to spin.
• Do not drive at extreme temperatures.
• Make sure the product does not come into contact with liquids.
• Do not touch the electrical circuit.

As the battery gets older it will start to lose some of its capacity. Depending on the conditions, it can last anywhere from 1 – 3 years. If the battery needs a replacement, follow these steps:

1. Loosen the crew and remove the seat.
2. Disconnect the cables from the battery terminals.
3. Remove the battery cover.
4. Carefully lift the battery out of the vehicle. Depending on the condition of the battery (leakage or similar), safety equipment may be required. Do not lift the battery from its wires but from the battery itself.
5. Put the battery in a plastic bag and dispose it responsibly. NEVER put the battery to general waste.
6. Insert the new battery into the vehicle.
7. Reconnect the cables to the new battery. Red wire to red terminal (+) and black wire to black terminal (-) of the battery.
8. Slide the seat into place. Tighten the screw.

To protect the environment, batteries, and electrical equipment must be disposed of separately from household waste. Contact the municipality for the nearest collection point.

Specification

12V-4.5Ah or

12V-7Ah

Power source:| Rechargeable battery| Charging Time:| 8 – 12 hours
Fuse:| 10A| Average battery life:| Approximately 300 Times

Operative norm:

• EN71-1
• EN71-2
• EN71-3
• EN62115

Installation

Charging

1. Insert 220V/12V charger cable’s connector to the vehicle as shown on the picture.
2. Insert actual 220V/12V charger unit to your 220V power outlet. The battery will start charging.
3. Detach after 8-12 hours

IMPORTANT NOTE:
When shifting (forward/backward), please make sure the vehicle is completely stopped, otherwise, it will damage the gearbox and motor.

Forward:

1. Press the ”Forward/backward switch” to the ”Forward” position.
2. Press the ”Foot pedal”, and the vehicle drives forward.

Stop:

1. The vehicle will brake automatically when the foot is lifted from the ” foot pedal”.

Back Up:

1. Press the ”Forward/backward switch” to the ”Backward” position.
2. Press the ”Foot pedal”, and the vehicle will back up.

Loosen the screw from the back of the seat seat, take away the seat. Then connect the battery line red wire to the red terminal of the battery and finally then connect black wire to black battery terminal. Never connect wires into the uncorrect battery terminals. After the connections, please assemble the seat back to the original place and tighten the screw.

Battery replacement and fuse

The battery is equipped with a thermal fuse which blows if the motor, battery or electrical circuit is overloaded. The vehicle must then be switched off for at least 5 minutes, after which the fuse will restore itself. If the product does not work, the fuse may therefore be the problem. To avoid this, read the following points:

• Do not overload the vehicle.
• Do not pull anything behind the vehicle.
• Do not drive up steep hills.
• Do not run into motionless objects that cause the wheels to spin.
• Do not drive at extreme temperatures.
• Make sure the product does not come into contact with liquids.
• Do not touch the electrical circuit.

As the battery gets older it will start to lose some of its capacity. Depending on the conditions, it can last anywhere from 1 – 3 years. If the battery needs a replacement, follow these steps:

1. Loosen the crew and remove the seat.
2. Disconnect the cables from the battery terminals.
3. Remove the battery cover.
4. Carefully lift the battery out of the vehicle. Depending on the condition of the battery (leakage or similar), safety equipment may be required. Do not lift the battery from its wires but from the battery itself.
5. Put the battery in a plastic bag and dispose it responsibly. NEVER put the battery to general waste.
6. Insert the new battery into the vehicle.
7. Reconnect the cables to the new battery. Red wire to red terminal (+) and black wire to black terminal (-) of the battery.
8. Slide the seat into place. Tighten the screw.

Assembly steps

• Step 1: Put the side wheels into the back axle on two sides, then put both gaskets and antiskid nuts on each side, tighten them.
• Step 2: Remove two screws with a screwdriver which the handlebar protectors fixed on the front fork, then insert the handlebar into the front fork hole and fix handlebar protectors with screws.
• Step 3: Insert the front visor into the front fork hole, then tighten with five screws.
• Step 4: After attaching the right side of the handlebars to the specified holes, the handlebars are installed. The left and right sides of the protective cover must be secured with five screws.
• Step 5: Fix the front handlebar cover and the handlebar alighment holes, then tighten them fixed with one screw on each side.
• Step 6: Insert the fender into front fork hole, then tighten with four screws. After that, insert the turning lights into both sides of the visor.
• Step 7: Put the front wheel on the front fork out of the front axle hole, insert a gasket, tighten the lock nut, and set bolt on each side.
• Step 8: First take out the long screw from the hole on the body. Next, insert the head into the slots on the body and plug the light wire connector into the connector on the body. Then Insert the long screw into the hole through the head and body, and tighten the screw.
• Step 9: Attach the rear cover to the hole on the back, and secure it with three screws. Afterward, a corner light is applied on two sides of the rear of the engine.
• Step 10: Press the mirror to the left and right holes in the handlebar.

Troubleshooting Guide

overload the vehicle.
Battery connector or wires are loose| Check that the battery connectors and

wires are firmly connected.

Battery is dead| Battery lasts 1-3 years. Replace battery and recycle the old battery responsibly.
Electrical system is damaged| Contact your distributor please.
Motor is damaged| Contact your distributor please.
Vehicle does not run very long| Battery is not properly charged.| Check that the battery connectors are firmly plugged into each other when recharging. Recharge battery again.
Battery is old| Battery lasts 1-3 years. Replace battery and recycle the old battery responsibly.
Vehicle runs sluggishly| Battery low on power| Check that the battery connectors are firmly plugged into each other when recharging. Recharge battery again.
Battery is old| Battery lasts 1-3 years. Replace battery and recycle the old battery responsibly.
Vehicle is overload| Reduce weight on vehicle. Maximum user weight is 25 kgs.
Vehicle is being used in unsuit- able conditions| Use the vehicle on flat, even surfaces.
Vehicle needs a push to go forward| Poor contact of wires or connectors| Check that the battery connectors are firmly plugged into each other when recharging. Recharge battery again.
“Dead Spot” on motor| A dead spot means the electric power is not being delivered to the terminal con nection and the vehicle needs re- pair. Contact your distributor please.
Difficult shifting from forward to

reverse or vice-versa

| Attempting to shift while the vehicle is motion| Always completely stop the vehicle before shifting.
Loud grinding or clicking noises coming from motor or gear box| Motor or gears are damaged| Contact your distributor please.
Battery will not recharge| Battery connector or adapter connector is loose| Check that the battery connectors are firmly plugged into each other when recharging. Recharge battery again.
Charger not plugged in| Check that the battery charger is plugged into a working wall outlet.
Charger is not working| Contact your distributor please.
Charger feels warm when recharging| This is normal and not a cause for concern|

Completely read through this manual and the troubleshooting guide table before calling. If you still need help resolving the problem Contact your distributor please.

Maintenance

• Check all screws periodically and tighten as needed.
• Check the vehicle’s plastic components frequently for damage.
• The mechanical parts of the vehicle can be lubricated with oil if necessary.
• Store the product indoors to protect it from the weather.
• Keep products away from hot items such as stoves and the like.
• Do not clean the product with a garden hose and do not use soap. A dry or moist cloth is enough.
• Do not drive in rain, snow, sand, and gravel as this may damage the product.

If the product is not to be used for an extended period, recharge the battery and then disconnect all cables

Imported by

NSH NORDIC A/S
Virkefeltet 4 DK-8740 Braedstrup

Made in China.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>