D-Link DXS-1210-10TS Layer 2+ SmartPro Switch User Guide
- October 30, 2023
- D-Link
Table of Contents
DXS-1210-10TS Layer 2+ Smart Pro Switch
User Guide
About This Guide
This guide gives step-by-step instructions for setting up switches and
relative Warranty, Safety, Regulatory, and Environment Notice. Please note
that the model you have purchased may appear slightly different from those
shown in the illustrations.
For more detailed information about your switch, its components, making
network connections, and technical specifications, please refer to the User’s
Guide included with your switch.
Unpacking
Open the shipping carton and carefully unpack its contents. Please consult the
packing list located in the User Guide to make sure all items are present and
undamaged. If any item is missing or damaged, please contact your local D-Link
reseller for replacement.
– One D-Link Switch
– Rack mounting bracket
– Power cord
– Power cord retainer
– User’s Guide CD with DNA (D-Link Network Assistant) program (optional)
– One multilingual Getting Started Guide
– An accessory kit for one ground screw
Switch Installation
For safe switch installation and operation, it is recommended that you:
- Visually inspect the power cord to see that it is secured fully to the AC power connector.
- Make sure that there is proper heat dissipation and adequate ventilation around the switch.
- Do not place heavy objects on the switch
Desktop or Shelf Installation
When installing the switch on a desktop or shelf, the rubber feet included
with the device must be attached on the bottom at each corner of the device’s
base. Allow enough ventilation space between the device and the objects around
it.
Figure 1. Attaching the rubber feet
Grounding the Switch (depending on the purchased model)
This section describes how to connect the Switch to ground. You must complete
this procedure before powering on your Switch.
Required Tools and Equipment
-
Grounding screws (included in the accessory kit):
One M4 x 6 mm (metric) pan-head screw -
Grounding cable (not included in the accessory kit):
The grounding cable should be sized according to local and national installation requirements.
Depending on the power supply and system, a 12 to 6 AWG copper conductor is required for installation. Commercially available 6 AWG wire is recommended. The length of the cable depends on the proximity of the Switch to proper grounding facilities. -
A screwdriver (not included in the accessory kit)
You can connect the Switch to a protective ground by following the steps below:
- Verify if the system power is off.
- Use the grounding cable to place the #8 terminal lug ring on top of the ground-screw opening.
- Insert the grounding screw into the ground-screw opening.
- Using a screwdriver, tighten the grounding screw to secure the grounding cable to the Switch.
- Attach the terminal lug ring at the other end of the grounding cable to an appropriate grounding stud or bolt on rack where the Switch is installed.
- Verify if the connections at the ground connector on the Switch and the rack are securely attached.
Figure 2. Connect a Grounding Cable
Installing Power Cord Retainer
To prevent accidental removal of the AC power cord, it is recommended to
install the power cord retainer together with the power cord.
- With the rough side facing down, insert the Tie Wrap into the hole below the power socket.
- Plug the AC power cord into the power socket of the Switch.
- Slide the Retainer through the Tie Wrap until the end of the cord.
- Circle the tie of the Retainer around the power cord and into the locker of the Retainer.
- Fasten the tie of the Retainer until the power cord is secured.
Rack Installation
The switch can be mounted in an EIA standard size 19-inch rack, which can
be placed in a wiring closet with other equipment. To install, attach the
mounting brackets to the switch’s side panels (one on each side) and secure
them with the screws provided.
Then, use the screws provided with the equipment rack to mount the switch in the rack.
Plugging in the AC Power Cord
You can now connect the AC power cord into the rear of the switch and to an electrical outlet (preferably one that is grounded and surge protected).
Power Failure
As a precaution, the switch should be unplugged in case of power failure. When
power is resumed, plug stitch back in.
Management Options
The D-Link Switch can be managed in-band by using Telnet. The user may also
choose the Web-based Management, accessible through a web browser or through
any PC using the DNA (D-Link Network Assistant).
If you want to manage only one D-Link Switch, the Web-Based Management is the
better option. Each switch must be assigned its own IP Address, which is used
forcommunication with Web-Based Management or an SNMP network manager and the
PC should have an Padres in the same range as the switch.
However, if you want to manage multiple D-Link Switches, the DNA (D-Link
Network Assistant) is the better option. Using the DNA (D-Link Network
Assistant), you don’t need to change the IP address of your PC and it is easy
to start the initial setting of multiple Switches.
Please refer to the following detailed installation instructions for the Web-
Based Management, DNA (D-Link Network Assistant), Telnet Management and SNMP-
Based Management.
Web-based Management Interface
After a successful physical installation, you can configure the switch,
monitor the LED panel, and display statistics graphically using a web browser,
such as Microsoft Internet Explorer version 7.0 and higher, Firefox, Chrome or
Safari.
You need the following equipment to begin the web configuration of your
device:
- A PC with a RJ-45 Ethernet connection
- A standard Ethernet cable
Step 1
Connect the Ethernet cable to any of the ports in front panel of the switch
and to the Ethernet port on the PC.
Step 2
In order to login and configure the switch via an Ethernet connection, the PC
must have an IP address in the same range as the switch. For example, if the
switch has an IP address of 10.90.90.90, the PC should have an IP address of
10.x.y.z (where x/y is a number between 0 ~ 254 and z is a number between 1
~254), and a subnet mask of 255.0.0.0.
Open your web browser and enter http://10.90.90.90 (the factory-default IP
address) in the address box. Then press
Figure 8. Enter the IP address 10.90.90.90 in the web browser
The web configuration can also be accessed through the DNA. You can click the
IP hyper link in the device list in the DNA to open the web GUI of devices.
NOTE: The switch’s factory default IP address is 10.90.90.90 with a
subnet mask of 255.0.0.0 and a default gateway of 0.0.0.0
Step 3
When the following logon box appears, enter “admin” for the password. Press OK
to enter the main configuration window.
Figure 9. Enter Network Password window
Step 4
Before entering the Web-based Management, the Smart Wizard will guide you to
quickly configure some functions, such as Password Settings, SNMP Settings,
and System Settings. If you don’t plan to change anything, click Exit to exit
the Wizard and enter the Web- based Management. For a detailed look at the
Smart Wizard’s functions, please refer to the Smart Wizard introduction in the
user manual.
DNA (D-Link Network Assistant)
The DNA (D-Link Network Assistant) is a program for discovering Switches with
the same L2 network segment connected to your PC. This tool can support
Windows2000, XP, Vista, and Windows 7. There are two options for the
installation of DNA (D-Link Network Assistant),one is through the autorun
program on the installation CD and the other is manual installation.
Option 1: Follow these steps to install DNA via the autorun program on the
installation CD (in case the installation CD is included):
- Insert the CD into your CD-ROM Drive.
- The autorun program will pop up automatically.
- Simply click on the “Install DNA (D-Link Network Assistant)” button and an_ installation wizard will guide you through the process.
- After successfully installing the DNA, you can find it under Start > Programs > D-Link > DNA.
- Just connect the Switch to the same L2 network segment of your PC and use the DNA (D-Link Network Assistant) to discover the Switches.
Option 2: Follow these steps to install DNA manually (in case the installation CD is included):
- Insert the CD into your CD-ROM drive.
- From the Start menu on the Windows desktop choose Computer.
- Double click on your CD-ROM/DVD-Rom Drive to start the autorun menu, or right click on the Drive to open the folder. Select DNA (D-Link Network Assistant) and double click on the setup.exe file.
- Follow the on-screen instructions to install the utility. 5. Upon completion, go to Start > Programs > D-Link > DNA and open DNA (D-Link Network Assistant).
- Just connect the Switch to the same L2 network segment of your PC and use DNA to discover the Switch. Option 3: (in case the installation CD is not included):
Download DNA (D-Link Network Assistant) from Google Play at https://play.google.com/store/apps/ and follow the on-screen instructions to install the utility.
For detailed information of DNA, please refer the user manual.
Telnet Management (depending on the purchased model)
Users may also access the switch through Telnet using your PC’s Command Prompt. To access it from your computer, users must first ensure that a valid connection is made through the Ethernet port of the Switch and your PC, and then click Start > Programs > Accessories > Command Prompt on your computer. Once the console window opens, enter the command telnet 10.90.90.90 (depending on configured IP address) and press Enter on your keyboard. You should be directed to the opening console screen for the Command Line Interface of the switch, enter the “admin” for the default user name and password for the Switch and press the Enter key.
SNMP-Based Management (depending on the purchased model)
You can manage the Switch with D-Link D-View or any SNMP-compatible
program. The SNMP function is default Disabled.
Additional Information
If you are encountering problems setting up your network, please refer to the
user manual that came with the switch. It contains many more rules, charts,
explanations, and examples to help you get your network up and running.
Additional help is available through our offices listed at the back of the
user manual or online. To find out more about D-Link products or marketing
information, please visit the website http://www.dlink.com.
Warranty Information
The D-Link Limited Lifetime Warranty information is available at http://warranty.dlink.com/
References
- warranty.dlink.com/
- For Home| D-Link
- For Home| D-Link
- D-Link Главная
- D-Link Главная
- D-Link Коммутаторы
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>