SZELAM EN8853A-RGB Digital Led Alarm Clock Instructions
- June 14, 2024
- SZELAM
Table of Contents
SZELAM EN8853A-RGB Digital Led Alarm Clock
Product Information
Specifications
- Mode l: EN8853A-RGB
- Display : Digital LED
- Power Source : Power cable
- Power Input: Jack (INPUT)
- Power Output: USB OUTPUT PORT, TYPE C OUTPUT PORT
- Power Jack : TYPE C cPOWER JACK
- Bottom Light : BOTTOM LIGHT, BOTTOM LIGHTING
- Alarm : ALARM SETTING
- Speakers: Built-in speakers
- Battery : Button Cell (CR2016)
Introduction of Buttons
- DISPLAY : Display settings
- Bottom Stand: S tand for the alarm clock
- TIME SETTING: Time setting mode
- AUTOMATIC DIMMING : Automatic dimming settings
- RGB/SNOOZE : RGB light settings and snooze mode
- DOWN : Decrease value or navigate down
- UP : Increase value or navigate up
- VOLUME : Adjust the volume
- USB OUTPUT PORT : Output port for USB devices
- TYPE C OUTPUT PORT : Output port for Type C devices
- TYPE C cPOWER JACK : Power input jack for Type C devices
- BOTTOM LIGHT : Bottom light settings
- BOTTOM LIGHTING : Bottom lighting settings
- SPEAKERS : Speaker settings
Operating Instructions
Note: Please connect the power cable to the jack (INPUT) on the right side of the alarm clock and then plug the power cable into the socket. The LED display turns on.
Switching 12/24Hr Time Mode
When it is in time mode (The default is 12 Hour mode), press the SET button to change the 12/24Hr time mode, the corresponding AM/PM icon will be light on/off.
Time Setting
- When it is in time mode, press and hold the SET button for 2 seconds to enter into the time-setting mode, the hour digits flash.
- Press the +/- button to set the current hour (hold to advance rapidly).
- Press the AL button again, and the minute digits flash. Press the +/- button to set the minute.
- Press the SET button again, and the minute digits flash. Press the +/- button to set the minute.
- Press the AL button again, save, and enter into a snooze-time setting mode (the 05 digit is flashing).
- Press +/- button to set the current snooze time. (Default 5 minutes, 5-60 minutes adjustable).
- Press the AL button again, save and exit the snooze-time setting mode.
- Press the SET button again, save and exit time-setting mode.
Alarm and Snooze Setting
- When it is in time mode, press the AL button to switch on/off the alarm, the corresponding will be light on/off.
- Press and hold the AL button for 2 seconds to enter into alarm-setting mode, and the hour digits flash.
- Press the +/- button to set the hour (hold to advance rapidly).
Alarm Buzzer Volume
Adjust the volume of the alarm buzzer using the VOLUME button.
When the Alarm Beeps
- BUZZER alarm lasts for 2 minutes.
- When the alarm beeps, press the SNOOZE button to enter snooze mode. The corresponding symbol flashes until it reaches the snooze time set and then the alarm beeps again.
- When the alarm beeps, press any other buttons except the SNOOZE button to turn off the alarm and snooze. The symbol stops flashing.
Setting Bottom RGB Light
Press and hold the BOTTOM LIGHT button for more than 2 seconds to switch between manual and auto mode for the bottom RGB light.
- In manual mode (default is OFF), press the + button to select light brightness: 100%-80%-50%-30%-10%-OFF by cycle.
- In auto mode, the brightness changes automatically based on the environment. When the environment is dark, the brightness is low; when the environment is bright, the brightness is high.
- Press and hold the LIGHT button for 3 seconds to turn off the light.
- Continue to press the BOTTOM LIGHT button to adjust the brightness.
Changing Colors of the LED Display
When it is in time mode, press the DISPLAY button to change the color of the LED display. The available colors are: Random Color, RGB Changing, RGB Left to Right Flowing, RGB Downward Top Flowing, White, Red, Yellow, Green, Light Blue, Blue, and Purple.
FAQ
Q: How do I switch between 12-hour and 24-hour time mode
A: When in time mode, press the SET button to toggle between the two modes.
Q: How do I set the alarm time
A: When in time mode, press and hold the AL button for 2 seconds to enter
alarm-setting mode. Use the +/- buttons to set the hour, and then press the AL
button again to set the minutes.
Q: How do I adjust the volume of the alarm
A: Use the VOLUME button to adjust the volume of the alarm buzzer.
Q: How does the snooze function work
A: When the alarm beeps, press the SNOOZE button to enter snooze mode. The
alarm will stop temporarily and start again after the snooze time is set.
Q: How do I change the color of the LED display
A: When in time mode, press the DISPLAY button to cycle through different
colors for the LED display.
Notes
- Some scratches appear on the protective film due to long-distance transportation, please tear the protective film off before using it. (Tips: As our protective film is very thin and fit well, it requires a little patience to find it and tear off.)
- Please remove the plastic insulator tab from the button battery compartment in the back and connect the product with electricity by USB or Adapter.
- The supplied battery is only for memorizing the time settings; it just could keep time memory when powered off, and couldn’t support the digital clock light up.
- If the time mode is 12-hour mode, when is Morning Time, there is an “AM” symbol in the display. When is Afternoon Time, there is a “PM” symbol in the display.
- When the alarm beeps, the red bottom lighting will flash, and then recovery to the preset status after the alarm stops.
- The automatic dimming set only works for screen displays.
Product Parameter
- RGB LED Time display ( 4 Dynamic RGB Changing Color and 7 Regular Color).
- There are 6 levels of brightness ( 100%-80%-50%-30%-10%-OFF).
- Automatic dimming set.
- Total 7 functional buttons (See the Introductions of buttons)
- 12/24 hour modes selectable( The default is 12 hour mode).
- The default Alarm display is 6:00.
- Alarm buzzer volume is adjustable (55dB-65dB-75dB-85dB-95dB).
- Alarm with Pre-settable Snooze function ( 5-60 minutes and unlimited times).
- Bottom RGB Light ( 10 Lighting Colors and brightness dimmable).
- There are 1 USB and 1 Type C Output port on the side (5V, 1A) which allows you to charge Android or Apple system smart phone in the same time.
Introduction of Buttons
Operating Instructions
Note: Please connect the power cable to the jack (INPUT) on the right side of the alarm clock and then plug the power cable into the socket. The LED display turns on.
Switching 12/24Hr Time Mode
When it is in time mode (The default is 12-hour mode), press the SET button
to change the 12/24Hr time mode, and the corresponding AM/PM icon will be
light on/off.
Time Setting
- When it is in time mode, press and hold the SET button for 2 seconds to enter into the time-setting mode, the hour digits flash. Press +/- button to set the current hour (hold to advance rapidly).
- Press the SET button again, and the minute digits flash. Press +/- button to set the minute.
- Press the SET button again, save and exit time-setting mode.
Alarm and Snooze Setting
- When it is in time mode, press the AL button to switch on/off the alarm, and the corresponding light on/off
- Press and hold the AL button for 2 seconds to enter into alarm-setting mode, and the hour digits flash. Press the +/- button to set the hour (hold to advance rapidly).
- Press the AL button again, and the minute digits flash. Press the +/- button to set the minute.
- Press the AL button again, save, and enter into a snooze-time setting mode (the “05” digit is flashing).
- Press the +/- button to set the current snooze time. (Default 5 minutes, 5-60 minutes adjustable).
- Press the AL button again, save, and exit the snooze-time setting mode.
Alarm Buzzer Volume
- When it is in time mode, press the VOL button to enter into the volume setting, the volume digits flash.
- Continue to press the VOL button to adjust the alarm buzzer volume. Buzzer Volume : 55dB-65dB-75dB-85dB-95dB.
When the Alarm Beeps
- BUZZER alarm lasts for 2 minutes.
- When the alarm beeps, pressbutton to enter snooze mode. The corresponding ” symbol flashes till reaches to the snooze time set and then the alarm again.
- When the alarm beeps, press any other buttons except the alarm and snooze. “ ” symbol stops flashing. button to turn off the
Automatic and manual dimming set
- Press and hold the button for more than 2 seconds. “OFF” displays which means manual mode(The default is “OFF”). In manual mode, press the + button to select light brightness: 100%-80%-50%-30%-10%-OFF by cycle.
- Press and hold the button for more than 2 seconds. “ON” displays which means auto mode. This means the brightness is changing automatically by the environment, when the environment is dark, the brightness is low; when the environment is bright, the brightness is high.
Changing Colors of the LED Display
When it is in time mode, press the button to change the color of the LED
display.The 11 colors sequence:
Random Color- RGB Changing- RGB Left to Right Flowing – RGB Downward Top
Flowing-White- Red -Yellow- Green – Light Blue-Blue-Purple
Setting Bottom RGB Light
- When it is in time mode, press a LIGHT button(the last button) to adjust the bottom light.
- Continue to press the LIGHT button can change colors. The 10-color sequence: RGB Flowing (Default)- RGB Changing- RGB Breathing-Warm White-Red-Yellow-Green-Light Blue-Blue-Purple.
- Press and hold the LIGHT button for 3 seconds to turn OFF the light.
- Continue to press – the button to adjust the brightness.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>