Meyer Cross TV1719 Rectangular Charcoal TV Stand Instruction Manual

Meyer Cross TV1719 Rectangular Charcoal TV Stand Instruction Manual

PRE-ASSEMBLY:

Two people are recommended to assemble this furniture. Carefully remove all parts and hardware from carton, along with any protective packaging. Locate and set aside the hardware kit before discarding packaging. Do not discard any contents until after assembly is complete to avoid accidentally discarding small parts or hardware.
Assemble the furniture on a soft surface, and take extra care not to scratch or damage parts during the assembly

 PRECAUTIONS — READ ALL BEFORE BEGINNING ASSEMBLY

Do not place items on the shelves which exceed the maximum weight limits of:
Top shelf: 75 lbs. (34.0 kg)
Lower shelves: 25 lbs. (11.3 kg) each

Usage with televisions or loads heavier than the maximum weights specified may result in instability, causing tip-over and resulting in death or serious injury. When in use, this furniture must be placed on a flat, solid and level surface.Do not climb or step on the shelves. Remove ALL items from the furniture before attempting to move the furniture. Do not use a drill or power tools to assemble this furniture, as it may weaken or damage parts. When moving the furniture, do not lift the furniture by the top shelf.

PARTS

NOTE: This illustration is for parts identification/orientation purposes only. For assembly, see following pages.

HARDWARE

content/uploads/2023/06/Screenshot_28-132.jpg)
| ****1
****14| **| **4
****15| **| **2
****16| **| **1**

INSTALLING THE CAM LOCKS

Do not overtighten!

1. Screw the Cam Screw into the prethreaded hole. Tighten with a screwdriver until snug.
   

2. The base of the Cam Screw should be flush with the panel.
   

3. Connect the panels. Insert the Cam Screw into the small hole in the adjoining panel.
   

4. The head of the Cam Screw should be visible through the large hole.
   

5. Insert the Cam Lock into the large hole. Make sure the arrow and the opening in the Cam Lock are facing the Cam Screw.

6. Using a screwdriver, turn the Cam Lock at least 90° clockwise to lock the two panels firmly together.
   

MAKE SURE THE ASSEMBLY IS DONE ON A LEVEL AND SOFT SURFACE (SUCH AS BLANKETS) TO PREVENT DAMAGING THE PARTS DURING ASSEMBLY.

NOTE: DO NOT OVERTIGHTEN SCREWS.

An assistant is recommended to HOLD the cabinet backing (F) in place while installing center screws (6) into the pilot holes. DO NOT TO OVERTIGHTEN SCREWS. Align cabinet backing (F) with cabinet frame before continuing.

View from rear of furniture.

An assistant is recommended to HOLD the cabinet backing (F) in place while installing screws (6). DO NOT TO OVERTIGHTEN SCREWS.

With the help of an assistant, turn TV stand upright.

NOTE: Use the leveling feet to make sure furniture is level on the floor before using.

SEE PAGE 21 FOR DOOR ALIGNMENT INSTRUCTIONS.

CARE INSTRUCTIONS:

• Wipe clean with a soft, dry cloth or static duster.
• Always avoid the use of harsh chemicals or abrasive cleaners as they may cause damage to the table’s finish.
• Hardware may loosen over time. Periodically check to make sure all connections are tight. Re-tighten if necessary.

Adjusting the doors

IMPORTANT — The furniture MUST be level on a flat, solid floor surface for the doors to work properly. Turn the leveling feet under the cabinet to make sure the furniture is level. Once the furniture is level, align the doors as shown for proper operation.

Top view

Front view

Documents / Resources

| Meyer Cross TV1719 Rectangular Charcoal TV Stand [pdf] Instruction Manual
TV1719, TV1720, TV1739, TV1719 Rectangular Charcoal TV Stand, Rectangular Charcoal TV Stand, Charcoal TV Stand, TV Stand, Stand
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>