FIBARO FGR-223 Roller Shutter 3 Instruction Manual

: June 6, 2024
: FIBARO

Table of Contents

Danger of electrocution
Basic activation of the device
Specifications
Warranty
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

FIBARO FGR-223 Roller Shutter 3 Instruction Manual

FIBARO FGR-223 Roller Shutter 3 Instruction Manual

FIBARO Roller Shutter 3 is a module designed to control roller blinds, awnings, venetian blinds, gates and other single phase, AC powered devices. FIBARO Roller Shutter 3 allows precise positioning of roller blinds or venetian blind lamellas. The device is equipped with power and energy monitoring. As with all other Actors, FIBARO Roller Shutter 3 allows to control connected devices either via the Z-Wave network or via a switch connected directly to it.

For full instruction manual and technical specification please visit our website: manuals.fibaro.com/en/roller-shutter-3
Read the manual before attempting to install the device!

FIBARO FGR-223 Roller Shutter 3 Instruction Manual - QR
Code http://manuals.fibaro.com/en/roller- shutter-3

Danger of electrocution

The Roller Shutter 3 is designed to operate in home electrical installation. Faulty connection or use may result in fire or electric shock. All works on the device may be performed only by a qualified and licensed electrician. Observe national regulations. Even when the device is turned off, voltage may be present at its terminals. Any maintenance introducing changes into the configuration of connections or the load must be always performed with disconnected voltage (disable the fuse).

Caution

Applied load and the device itself may be damaged if the type and values of applied load are inconsistent with the technical specification! Connect only in accordance with one of the diagrams presented in the full manual. Incorrect connection may cause risk to health, life or material damage. The device is designed for installation in a wall switch box of depth not less than 60mm. The switch box and electrical connectors must be compliant with the relevant national safety standards. It is not recommended to operate all of the roller blinds simultaneously. For safety reasons, at least one roller blind should be controlled independently, providing safe escape route in case of emergency. Do not expose this product to moisture, water or other liquids. This product is designed for indoor use only. Do not use outside! This product is not a toy. Keep away from children and animals!

Basic activation of the device

Switch off the mains voltage.
Open the wall switch box.
Connect the device in accordance with the diagram.
Wiring diagram connection with AC motor (more wiring diagrams available in the full manual)

FIBARO FGR-223 Roller Shutter 3 Instruction Manual - Basic activation of the
device

Arrange the antenna and close the wall switch box.
Switch on the mains voltage.
Set the main Z-Wave controller into adding mode.
Quickly, triple click switch connected to the S1 terminal.
Wait for the device to be added into the system.
Three times press and hold switch connected to S1 or S2 for at least 3 seconds.
The device will perform the calibration completing a full cycle.

Specifications

FIBARO FGR-223 Roller Shutter 3 Instruction Manual -
Specifications

Simplified EU declaration of conformity: Hereby, Fibre Group S.A. declares that the device is in compliance with Directives 2014/53/EU and 2011/65/EU, 2015/863. The full text of the EU declaration of conformity is available at the following internet address: www.manuals.fibaro.com

WEEE Directive Compliance: Device labelled with this symbol should not be disposed with other household wastes. It shall be handed over to the applicable collection point for the recycling of waste electrical and electronic equipment.

Warranty

FIBAR GROUP S.A. with its registered office in Wysogotowo, ulu. Serdeczna 3, 62-081 Wysogotowo, entered into the Register of Entrepreneurs of the National Court Register maintained by the District Court for Pozna-Nowe Impasto and Wilda in Poznan, VIII Commercial Division of the National Court Register (KRS) under number: 553265, NIP 7811858097, REGON: 301595664, share capital PLN 1,182,100 paid in full, other contact information is available at: www.fibaro.com (hereinafter “the Manufacturer”) guarantees that the device sold (hereinafter: “the Device” is free from material and manufacturing defects.
The Manufacturer shall be responsible for malfunctioning of the Device resulting from physical defects inherent in the Device that cause its operation to be incompatible with the specifications within the period of: – 24 months from the date of purchase by the consumer, – 12 months from the date of purchase by a business customer (the consumer and business customer are further collectively referred to as “Customer”).
The Manufacturer shall remove any defects revealed during the guarantee period, free of charge, by repairing or replacing (at the sole discretion of the Manufacturer) the defective components of the Device with new or regenerated components. The manufacturer reserves the right to replace the entire Device with a new or regenerated device. The Manufacturer shall not refund money paid for the device.
Under special circumstances, the Manufacturer may replace the Device with a different device most similar in technical characteristics.
Only the holder of a valid guaranty document shall be entitled to make claims under guarantee.
Before making a complaint, the Manufacturer recommends using the telephone or online support available at https://www.fibaro.com/support/.
In order to make a complaint, the Customer should contact the Manufacturer via the email address given at https://www.fibaro.com/support/.
After the complaint has been properly filed, the Customer will receive contact details for the Authorized Guarantee Service (“AGS”). The customer should contact and deliver the Device to AGS. Upon receipt of the Device, the manufacturer shall inform the Customer of the return merchandise authorization number (RMA).
Defects shall be removed within 30 days from the date of delivering the Device to AGS. The guarantee period shall be extended by the time in which the Device was kept by AGS.
The faulty device shall be provided by the Customer with complete standard equipment and documents proving its purchase.
The cost of transporting the Device in the territory of the Republic of Poland shall be covered by the Manufacturer. The costs of the Device transport from other countries shall be covered by the Customer. For unjustified complaints, AGS may charge the Customer with costs related to the case.
AGS shall not accept a complaint claim when:
– the Device was misused or the manual was not observed,
– the Device was provided by the Customer incomplete, without accessories or nameplate,
– it was determined that the fault was caused by other reasons than a material or manufacturing defect of the Device
– the guarantee document is not valid or there is no proof of purchase,
The guarantee shall not cover:
– mechanical damages (cracks, fractures, cuts, abrasions, physical deformations caused by impact, falling or dropping the device or other object, improper use or not observing the operating manual);
– damages resulting from external causes, e.g.: flood, storm, fire, lightning, natural disasters, earthquakes, war, civil disturbance, force majeure, unforeseen accidents, theft, water damage, liquid leakage, battery spill, weather conditions, sunlight, sand, moisture, high or low temperature, air pollution;
– damages caused by malfunctioning software, attack of a computer virus, or by failure to update the software as recommended by the Manufacturer;
– damages resulting from: surges in the power and/or telecommunication network, improper connection to the grid in a manner inconsistent with the operating manual, or from connecting other devices not recommended by the Manufacturer.
– damages caused by operating or storing the device in extremely adverse conditions, i.e. high humidity, dust, too low (freezing) or too high ambient temperature. Detailed permissible conditions for operating the Device are defined in the operating manual;
– damages caused by using accessories not recommended by the Manufacturer
– damages caused by faulty electrical installation of the Customer, including the use of incorrect fuses;
– damages caused by Customer’s failure to provide maintenance and servicing activities defined in the operating manual;
– damages resulting from the use of spurious spare parts or accessories improper for given model, repairing and introducing alterations by unauthorized persons;
– defects caused by operating faulty Device or accessories.
The guarantee shall not cover natural wear and tear of the Device and its components listed in the operating manual and in technical documentation as such elements have a defined operational life.
The Device Guarantee shall not exclude, limit or suspend the Customer’s warranty rights.
The Manufacturer shall not be liable for damages to property caused by defective device. The Guarantor shall not be liable for indirect, incidental, special, consequential or punitive damages, or for any damages, including, inter alia, loss of profits, savings, data, loss of benefits, claims by third parties and any other damages arising from or related to the use of the Device.