R-Go Tools Caparo 4 D2 Circular Single Monitor Arm User Manual
- June 9, 2024
- R-Go Tools
Table of Contents
Circular monitor arm
R-Go Caparo 4 D2 &
R-Go Zepher 4 C2
Nachhaltiger Monitor Arm
Tips for healthy screen use
Did you know that a wrong set-up of your monitor has a negative effect on your working posture? You can easily get physical complaints, such as neckpain. Here some tips to create a healthy set-up:
- Place the top of your screen at eye level. You will automatically sit up straight.
- Place your screen at least at arm’s length to give some relieve to your eyes.
- Place your screen directly in front of you. This way, you will adopt an straight posture while working.
To make maximum use of the depth of your desk, we recommend that you do not
fix the base of the monitor arm in the middle, but position it approximately
45 cm out of the middle of the desktop.
Do you work with two monitors? We recommend to place the most frequently used
screen right in front of you. The other (additional) screen should be placed
directly next to it, at the same height, and pulled slightly towards you.
This set-up ensures that you will sit straight most of your working day.
What’s in the box?
R-Go Caparo 4 D2 Single Monitor Arm
R-Go Zepher 4 C2 Single Monitor Arm
R-Go Caparo 4 D2 Dual Monitor Arm
R-Go Zepher 4 C2 Dual Monitor Arm
Setup
Single monitor arm
Step 1 Slide the base 1 onto the desktop. Tighten the screw A with the hex key
B.
Step 2a Insert the pole 2 into the base 1 until you hear it make contact
with the table.
Step 2b Keep the pole 2 pressed down while tightening the ring .
Smart Stop™
Create your own setup
*Smart Stop™
: At the bottom of the ring there is a small arrow. This arrow indicates where
the Smart Stop is, i.e. where the arm stops ™ rotating. It is important
to have the arrow on the correct side (left or right), so that the arm stops
rotating and for example does not bump into an acoustic screen (see p. 10 & 11
for setup).
Step 3a Choose which Smart StopTM setupLou want (setupli 2 e or IP, see
page 10-11).
Step 3b Place the forearm 0 on the pole O. Make sure the arrow points in
the direction of the number of your chosen setup. See numbers on the base
(1:114) or Czia)).
Step 4a Place the upper arm 0 on the forearm O. While doing so, make sure
that the arrow point in the direction of the number of your chosen setup. See
numbers on the base (;m or 314:).
Step 4b Push the upper arm 0 down while tightening the ring e.
Step Sa Place the head ® on the upper arm ®. Make sure that the arrow points
in the direction of the arrow on the upper arm.
Step Sb Press the head down while tightening the ring
Step 6a
Attach the VESA plate 6 to the monitor using the enclosed hexagonalscrews
(see VESA plate). Use the enclosed hex key A to do this. Click the VESA plate
6 onto the head 5.
Step 6b
In order to straighten the monitor, you will find 3 screws at the back of the
VESA plate 6 . The screws can be tightened with the enclosed hex key, so you
can increase the resistance and straighten the monitor.
Step 6c (Only for R-Go Caparo 4 D2)
Depending on the weight of your monitor, you can increase or decrease the
resistance of the gas spring arm (upper arm 4 ) by tightening the hexagonal
screws. Use the enclosed hex key.
Step 6d (Only for R-Go Zepher 4 C2)
Set the arm at the correct height by sliding the lower arm on the pole. Then
tighten the ring on the lower arm.
Dual monitor arm
Install the first arm following step 1-6 and follow step 3-6 to install the
extra arm.
Watch How To Set Up
Your Monitor Arm
http://r-go.tools/monitor_arm
Documents / Resources
| R-Go
Tools Caparo 4 D2 Circular Single Monitor
Arm
[pdf] User Manual
Caparo 4 D2, Zepher 4 C2, Circular Single Monitor Arm, Single Monitor Arm,
Circular Monitor Arm, Monitor Arm, Arm
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>