Klahaite K15 ZAP PRO Electronic Bug Zapper User Manual

ELECTRONIC BUG ZAPPER
USER MANUAL

SAVE THIS MANUAL FOR FUTURE REFERENCE
KlS ZAP PRO

INTRODUCTION

THANKS FOR PURCHASING OUR PRODUCT, FOR OPTIMAL PERFORMANCE, PLEASE READ THIS MANUAL CAREFULLY.

Please check the condition of the device before use, If the device is damaged, do not use it.
A wavelength of 365 nm emitted by the highly efficient UV tube attracts bugs, mosquitoes, Insects and flies etc into device and get an elec­ tric shock immediately when they touch the electrified grid.
The device is highly efficient and energy-saving. It is de­signed for continuous use and is ready to provide you with a long mosquito-free pastime for many years

PRODUCT SPECIFICATIONS
Model: K15 ZAP PRO
Input Voltage: 120V
Working Current: 0.22A
Rated Frequency: 60HZ
Grid Voltage: 3600-4200V
Bulb Wattage: 15W
Bulb Type: FUL 4-Pin Single U-Shaped Twin Tube

SAFETY INSTRUCTIONS

  Do not use in inflammable or explosive ocales and alike.
  Check the local voltage codes before installing.
  Do not intend to touch internal high voltage grids because of electric shock danger. Never put metal objects inside the net during use.
Hang or place the appliance out of the reach of children.
  Never remove any fixed part of the appliance to make internal adjustments to avoid electric shock.
  Do not clean this product with water, spray or anyother liquids. Do not immerse any part of this applianceor supply cord in water. Do not use with wet hands or in damp environments.
  Clean metal grid at frequent intervals, unplug the appliance before cleaning. Use suitable brush to clean the high voltage grids and throw away the insects debris from the collection tray every week.

WHERE AND HOW TO USE

INDOOR
The product can be used in the bedroom, living room, hotel, restaurant, office, etc. the product has an energy-saving design and soft lighting, so it shouldn’t be used in high light conditions, otherwise, it will affect the destruction of mosqui­ toes.

  The right methods for using the device are below:
A. keep the house lighting off and use device before sleeping.
B. Turn off all strong lighting for 10-20 minutes.
C. keep the product in the dark place while working.
D. Suggested suspension height: place or hang the product at a height of 1.2m at a distance of 0.3m from the wall.

Notice: Ultraviolet or “black light” is invisible to the eye, Its ability to attract nsects diminishes over time. Therefore, although the bulb appears to be functioning, it should be replace every season to maintain optimal “black light” efficiency.

OUTDOOR

Hang the bug zapper at a height of 6 to 8 feet above the ground.
Place the device 25 feet away from the area intended for human activity.
  Position the bug zapper between the source of insects (woods, lowlands, etc) and the area to be protected.
Plug into a compatible extension cord signed for outdoor use, a blue glow will be emitted by the device within n a few seconds.
To increase the killing rate, please clean nsects debris stuck in the gnd. please keep the power off, then use included cleaning brush to gently clean it. It’s recommended that the unit be put to use in early spring and left out late fall to maxi­ mize effects.

HOW TO REPLACE BULB

1. To prepare for bulb replacement.unplug unit and allow it to sit for two hours to allow the electri­ cal charge within the unit to dissipate.
2. Twist and remove the tray. (Fig.1)
3.  Remove both screws securing grate panel. (Fig.2)
4.  Lift up grate to access bulb. (Fig.3)
5. Wearing gloves, Gently tug on the bulb to remove. (Fig.4)
6. Replace bulb only with proper 1sw replacement bulbs, then wearing gloves, insert replacement bulbs making sure they are properly seated nto the sockets that they were removed from.
7. Gently apply pressure on bulbs until they snap into socket securely.
8. Place grate plate back into position and fasten with screws.
9. If using base tray, twist back into place on bottom of unit.
10. Plug in to test replaced bulb functions properly.

Note: f device falls to ight after bulb replacement, unplug device, and follow the instructions above ensure that the bulb was correctly installed, and re-assemble unit.

TROUBLE SHOOTING

CAUTION: UNPLUG UINT BEFORE SERVICING

2. Check all sockets for proper fit and alignment.
3. Make sure unit is plugged into a working outlet.
B. Bulb light on, but no high voltage on grid.| 1. Shorted grids.
2. The transformer is defective.| 1. Examine the grid and clean it with the brush supplied.
2. Replacement by manufacturer required.
C. Grid voltage present, but bulbs do not light.| 1. Bulb not seated properly.
2. Burned out bulb.| 1. Check all sockets for proper seating and alignment, 3 prongs are connected into unit.
2. Unplug the unit and replace the bulb, please read bulb replacement section in the user manual.
D. Intermittent or continuous sparking between grid rods.| 1. Gap between grid rod is too small.
2. Grid clogged with foreign objects.
3. Large insect has moved wire grid closer causing the grid to sparking constantly.| 1. Unplug the unit and adjust grids by bending them back into alignment or contact After Sales Support.
2. Unplug the unit and clean the grid with the brush supplied.
E. The bulb lights, but no longer attacts insects.| 1. Invisible blacklight output reduce due to the bulb age.
2. Bug Zapper is positioned incorrect /not operated at correct times.| 1. Unplug the unit and replace the bulb, please read bulb replace-ment section in the user manual.
2. Insect population may be low, try moving the unit to a different location, operate 24/7 or dusk to dawn.

HOW TO CLEAN

ELECTRIC GRID CLEANING

1. Unplug the device and remove unit from hanging position and allow it to sit for two hours to allow all electricity in unit to disperse.
2. Access grid through the open slots in grill as shown using included cleaning brush and gently brush away dead nsects so they fall down into the ower tray for removal, Be carefully and make sure not to move the metal electric grid. (Fig.5)
3.  Never use water to clean the unit as this can cause damage to the electronics.

REMOVING &CLEANING BOTTOM TRAY 

1. If using removable bottom tray, make sure to clean the tray often of dead insects.
2. Unplug the unit and twist the bottom tray as shown(Fig.1 ). (Fig.6) then rinse and dry it, avoid touch insect by hand.
3. The exterior housing of bug zapper does not require cleaning. Do not attempt to clean the housing with water or spray any other liquids.

CUSTOMER SERVICE
BEFORE YOU CALL CUSTOMER SERVICE:

1. Check to make sure that the unit is plugged in securely. If it is not, remove the plug from the outlet, wait 1 O seconds and plug it in again securely.
2. Check for a blown circuit fuse or a tripped main circuit breaker. If these seem to be operating properly, test the outlet with another appliance.

WARNING:
Do not try to adjust or repair the zapper by yourself.
Component parts shall be replaced with like compo­ nents. Servicing shall be done by factory authorized service personnel to minimize the risk of possible gnition due to incorrect parts or improper service.

ONE YEAR LIMITED WARRANTY:
We warrants to the original purchaser that the product will be free from defects in material, parts and workmanship for the period designated for this product
The warranty commences the day the product is purchased and covers up to a period of 1 year ( 12months )for labor 1 year ( 12months )(manufacturingdefectsonly )/carryin ser­ vice /anda total of 1 years (12month )
If you experience unsatisfactory operation, frist refer to the “Trouble Shooting” section of this manual and follow those suggestions. If Trouble Shooting doesn’t work, please feel free to contact our After-sale Service Department.

Thank you for choosing K15 ZAP PRO!
www.klahaite.com
support@klahaite.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>