WINNERCOM CN7 PE NFC Touch Door Handle User Manual
- October 30, 2023
- Winnercom
Table of Contents
- WINNERCOM CN7 PE NFC Touch Door Handle
- Product Information: WINNERCOM CN7 PE NFC Touch Door Handle
- Product Usage Instructions
- Introduction
- NFC DHS Design(BOM) & Application
- Attentions
- Specifications
- User Information and Instructions
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
WINNERCOM CN7 PE NFC Touch Door Handle
Product Information: WINNERCOM CN7 PE NFC Touch Door Handle
The WINNERCOM CN7 PE NFC Touch Door Handle is a door handle module for automotive use. It features an NFC reader and lock/unlock 2-channel capacitive touch sensor function. The module is installed inside of the door handle covers and is attached to the outside door panel. It communicates with the car network through a Hi-Speed CAN network, enabling it to send signals for locking and unlocking the door and controlling the pocket light LED on/off. The module receives DC power from the car battery at all times. The handle is made of polyurethane full potting inside of the module, which protects it from humidity, vibration, and waterproofing. The case is made of PA6+GF15%, ABS/PRESS: SPTE(Tin-Plating), PCB: FR-4, 4Layer, Foam Tape: EPDM/FPCB: Polyimide film.
Product Usage Instructions
- Mount the Door handle Module before powering on the device to avoid circuit damage.
- Check the power supply before powering on the Module (refer to Fig. 1). Connect Module Input Power to the connector (refer to Fig. 1).
- Use twisted wires between the connector and the door handle module for CAN (HI) and CAN (LO) communication lines. The twist should be applied once per inch (360 degrees).
Note: This device complies with part 15 of the FCC rules. Any changes or modifications not approved by the compliance party could void the user’s authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Introduction
- Door handle Module (DHS)
- NFC & Capacitive Touch
- Pocket Light LED
- Hi-Speed CAN
The door handle module for Automotive has a NFC Reader and lock/Unlock
2Channel Capacitive touch Sensor function. This module is installed inside of
the door handle covers and will be attached to the outside door panel. This
module is communicated with CAN network which enables to connect to the car
network to send the signal of lock and unlock of door and Pocket light LED
On/Off control. It receives DC power from car battery at all time.
NFC DHS Design(BOM) & Application
CE – NFC Touch Door Handle
| ITEMS | SPECIFICATION |
|---|---|
| Size | 150 x 18.3 x 22(h) [mm] (Length x Width x Height) |
| Color | Black |
| Weight | 60g |
| Waterproof | Polyurethane full potting inside of module. Protective of humidity |
,vibration, waterproof.
Material| Case : PA6+GF15% , ABS / PRESS : SPTE(Tin-Plating) / PCB : FR-4,
4Layer / Foam Tape : EPDM/ FPCB : Polyimide film
Attentions
- Please always mount the Door handle Module before power on the device to avoid circuit damage
- Before power on the Module, check the power supply(Fig. 1)
- Module Input Power connect to the connector(Fig. 1)
CAN (HI), CAN (LO) communication lines shall be applied as twisted wires between the connector and the door handle module. The twist is applied once per inch (360 degrees).
Specifications
NFC Touch Data
Frequency Range| 13.56MHz for NFC
Operating Voltage| 9.0 ~ 16.0 [Vdc], Typical 12.0 [Vdc]
Current| Max 400mA @ Operation Mode
Operating Temp.| -30℃ ~ 75℃
Storage Temp.| -40℃ ~ 85℃
User Information and Instructions
FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference,
- this device must accept any interference received, including interference that may cause undesired operation.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Industry Canada Statement
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference,
- this device must accept any interference received, including interference that may cause undesired operation.
Manufacturer information
Manufacturer name
| ****
WINNERCOM Co., Ltd.
---|---
Address, City:
| ****
158-7, Golden root-ro, Juchon-myeon, Gimhae-si, Gyeongsangnam-do, KOREA
Product name (type) :
| ****
Touch door
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>