Winnercom LX2PE NFC Touch Door User Manual

June 5, 2024
Winnercom

Winnercom LX2PE NFC Touch Door User Manual
Winnercom LX2PE NFC Touch Door

Introduction

  • Door handle Module (DHS)
  • NFC & Capacitive Touch
  • Pocket Light LED
  • Hi-Speed CAN

The door handle module for Automotive has a NFC Reader and lock/Unlock 2Channel Capacitive touch Sensor function.
This module is installed inside of the door handle covers and will be attached to the outside door panel.
This module is communicated with CAN network which enables to connect to the car network to send the signal of lock and unlock of door and Pocket light LED On/Off control.
It receives DC power from car battery at all time.
Cover Assembly
[ Assembled cover and DHS]

NFC DHS Design(BOM) & Application

ITEMS

|

SPECIFICATION

---|---
Size| 125 x 18 x 20 mm (Length x Width x Height)
Color| Black
Weight| 53g +/- 2.2%
Waterproof| Polyurethane full potting inside of module. Protective of humidity ,vibration, waterproof
Material| Case : PA6+GF15% , ABS / PRESS : SPTE(Tin-Plating) / PCB : FR-4, 4Layer / Foam Tape : EPDM/ FPCB : Polyimide film

Exploded Parts

NO

| Lev|

SUB

---|---|---

1

| 1| CASE UPPER
2| 1|

CASE LOWER

3

| 1| PCB ASSY
4| 1|

FPCB.

5

| 2| FOAM PAD LED
6| 2|

CABLE ASSY

7

| 1| FOAM PAD A
8| 1|

FOAM PAD B

9

| 1|

ANT POTTING

Attentions

  • Please always mount the Door handle Module before power on the device to avoid circuit damage
  • Before power on the Module, check the power supply (Fig. 1)
  • Module Input Power connect to the connector (Fig. 1)
    CONNECTOR INFORMATION
    DC 12V Input for operate Door Handle Module (#1 &
    6)
    Fig. 1 Connector

CONNECTOR INFORMATION

  • O/S HDL CONNECTOR
  • Female Connector : HKCO6 .272

Touch+NFC (CAN + Logic Signal)


Pin

| Pin Name| Wire Color|

Signal Description

1

| V Bat(+Vcc)| Red| Power Supply
2| L_CAN(L)| Green|

CAN Low Signal

3

| Touchl| Gray| Lock
4| Touch2| Pink|

Unlock

5

| L_CAN(H)| Blue| Blue CAN High Signal
6| GND| Black|

Electrical Ground

  • CONNECTOR
  • Male Connector : HKCO6-12711

Specifications

NFC Touch Data


Frequency Range| 13.56MHz for NFC
Operating Voltage| 9.0 ~ 16.0 [Vdc], Typical 12.0 [Vdc]
Current| Max 0.50mA @ Sleep Mode, Max 100mA @ Operation Mode
Operating Temp| -35℃ ~ 75℃
Storage Temp.| 40℃ ~ 85℃

★ DHS : Door Handle System

System Block Diagram

User Information and Instructions

FCC Part 15 Compliance information.

FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Industry Canada Statement

This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:

  1. this device may not cause interference, and this device must accept any interference, including interference that may cause undesired operation of the device.

Manufacturer information

Manufacturer name WINNERCOM Co., Ltd.
Address, City: HUMAX Village, 216, Hwangsaeul-ro, Bundang-Gu,

Seongnam-si, Gyeonggi-do, South KOREA 13595
Product name (type) :| Vehicle active antenna & Touch door

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals