WINNERCOM MX5 NFC Touch Door Handle User Manual
- June 14, 2024
- Winnercom
Table of Contents
MX5 NFC Touch Door Handle
User Manual
V 1.0
MX5 NFC Touch Door Handle
Winnercom Co., Ltd.
Introduction
- Door handle Module (DHS)
- NFC & Capacitive Touch
- Pocket Light LED
- Hi-Speed CAN
The door handle module for Automotive has a NFC Reader and lock/Unlock
2Channel Capacitive touch Sensor function.
This module is installed inside of the door handle covers and will be attached
to the outside door panel.
This module is communicated with CAN network which enables to connect to the
car network to send the signal of lock and unlock of door and Pocket light LED
On/Off control.
It receives DC power from car battery at all time.
NFC DHS Design(BOM) & Application
NFC Touch Door Handle
| ITEMS | SPECIFICATION |
|---|---|
| Size | 174.4 x 18.3 x 13(h) [mm] (Length x Width x Height) |
| Color | Black |
| Weight | 62(g) ±2.2% |
Attentions
- Please always mount the Door handle Module before power on the device to avoid circuit damage
- Before power on the Module, check the power supply(Fig. 1)
- Module Input Power connect to the connector(Fig. 1)
– Type: 6pin Connector Sealed
– Maker & Part No.: MI HKC06-12721 6P Female
| Pin # | Name | Description | In/Out | Wire Color | I/O Level |
|---|---|---|---|---|---|
| 1 | V Bat(+Vcc) | Power Supply | Power | RED | Battery |
| 2 | L_CAN(L) | CAN Low Signal | I/O | GREEN | 2.5±TBD V |
| 3 | TOUCH 1 | LOCK | O | GRAY | |
| 4 | TOUCH 2 | UNLOCK | O | PINK | |
| 5 | L_CAN(H) | CAN High Signal | I/O | BLUE | 2.5±TBD V |
| 6 | GND | Electric Ground | Power | BLACK | Gnd |
Fig. 1 Connector
Specifications
NFC Touch Data
| Frequency Range | 13.56MHz for NFC |
|---|---|
| Operating Voltage | 9.0 ~ 16.0 [Vdc], Typical 12.0 [Vdc] |
| Current | Max 400mA @ Operation Mode |
| Operating Temp. | -30℃ ~ 75℃ |
| Storage Temp. | -40℃ ~ 85℃ |
| Symbol | DC, IEC 60417-5031 (2002-10) |
| NFC maximum output power | FCC/IC = 19.08 dBuV/m at 3m, CE = -8.00 dBuA/m at |
10m
User Information and Instructions
FCC Part 15 Compliance information.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions :
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
FCC Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Industry Canada Statement
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation of
the device.
Manufacturer information
| Manufacturer name | WINNERCOM Co., Ltd. |
|---|---|
| Address, City: | 158-7, Golden root-or, Juchon-myeon, Gishie-si, Gyeongsangnam- |
do, KOREA
Product name (type) :| Touch door
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>