TOMOLOO K1 X-Men Hoverboard 6.5 Inch Self Balancing Electric Scooter User Manual

X-MAN K1 HOVERBOARD
OPERATION MANUAL

ATTENTION & SAFETY INSTRUCTIONS

• The operating temperature range of the charger is 32°-1 04°F (0°-40°C)
• The operating temperature range of the K1 is 32*-1 04°F(0°-40°C).
• Do not ride on icy or slippery surfaces. Read the user manual before riding.
• Store the K1 in a dry, ventilated environment.
• When transporting the Kl, avoid violent crashes or impacts.
• When the device displays a low battery or no power placed for more than 3 months, the battery will enter sleep mode and can’t be charged anymore.
• We suggest charging the device each month.
• After leaving your device for more than 15 minutes and without any operation, the device will automatically shut down.

LOW-TEMPERATURE WARNING

Low temperature will affect the lubrication of moving parts inside the K1 hoverboard, increasing internal resistance. At the same time, in low temperatures, the discharge capacity and the capacity itself of the battery will significantly be decreased. Do not ride the K1 violently in low temperatures around or below 32° F (0°C).

SAFETY INSTRUCTIONS

• Keep the device away from heat sources, direct sunlight, humidity, and prolonged exposure to water.
• Do not operate the device if it has been exposed to water, moisture, or any other liquids to prevent electric shock, explosion, and/or injury to yourself and damage to the device.
• Do not use the device if it has been dropped or damaged in any way.
• Repairs to electrical equipment should only be performed by a qualified electrician. Improper repairs may place the user at serious risk.
• Do not puncture or harm the exterior surface of the product in any way.
• Keep the device free from dust, lint, etc.
• Do not use this device for anything other than its intended use or purpose. Doing so may damage the device.
• This product is not a toy. Keep out of reach of children.
• Do not expose batteries, battery packs, or batteries installed to excessive heat, such as direct sunlight, or open flame.

Chapter 1

ABOUT THIS MANUAL

PLEASE READ THE USER MANUAL THOROUGHLY. Failure to follow the basic instructions and safety precautions listed in the user manual may damage your device or cause bodily injury.

Thank you for purchasing the TOMOMLOO K1 hoverboard. Please read all instructions carefully before using and retain this manual for future use and reference.
This manual applies to the TOMOLOO K1 hoverboard.

• In order to avoid dangers caused by collisions falls, and loss of control, please learn how to ride safely.
• You can learn operating skills by reading the product manual.
• This manual includes all operating instructions and precautions, and users must read it carefully and follow the instructions.
• All users are responsible for any consequences caused by violating warning contents or prompt operations.

Chapter 2

PRODUCT INTRODUCTION

The TOMOLOO K1 is a personal transporter. Our technology and production processes are developed with strict testing for each TOMOLOO hoverboard. Driving without following the contents of this manual may lead to damage to your device, or may cause bodily injury.
This manual is designed to give you the information you need for the safe operation and maintenance of your new K1. Please read it thoroughly before riding your K1.

2-1. PACKAGE CONTAINS

• TOMOLOO K1 Hoverboard
• 3-pin Charge Cable
• Operation Manual (21.471b/9.74 kg)

2-2.FEATURES/PARTS

1. Fender
2. Left Foot Mat
3. Running Indicator
4. Power/Battery Indicator
5. Right Foot Mat
6. Path Illuminating Lights
7. Side LED Lights
8. Power Button (Located In rear)
9. Charge Port (Located in rear)
10. Solid Tire/Motor

2-3.OPERATING PRINCIPALS

The device uses digital electronic gyroscopes and acceleration sensors to control balance and motion, depending on the user’s center of gravity. The device also uses a control system to drive the motors that are located within the wheels. The device has a built-in inertia dynamic stabilization system that can help assist with balance when moving forward and backward, but not while turning.

TIP – To increase your stability, you should keep your body be balanced in order to overcome the centrifugal force during turns, especially when entering a turn at higher speeds.

Any 1(1 hoverboard that does not work properly can cause you to lose control and fall. Check the entire device thoroughly before every ride, and do not ride it until any problems have been corrected.

2-4.SPECIFICATIONS

“The above data is based on laboratory test results, the actual date may be different according to the weight of users, road conditions, temperature, etc.

2-S.CONTROLS AND DISPLAY

TURNING YOUR DEVICE ON/OFF
Power On: Take your device out of the box and place it flat on a level surface. Press the power button (located on the rear of your device) once. Check the battery LED indicator (located in the center of your device). The battery indicator light should be lit, indicating the device is powered on. Power Off: Press the power button once.

MAT SENSOR
There are four sensors under the foot mats on your 1<1 hoverboard. When the user steps off the mats, it will automatically initiate self-calibration. When riding the hoverboard, you must ensure you are stepping on the foot mats. Do not step or stand on any other area of your hoverboard. Do not put items on the foot mats. Doing so will make the K1 turn on, increase the probability of collision and cause injury to people, riders, or damage to the device.

BATTERY INDICATOR
The display board is located in the middle of the K1 hoverboard.

• A green LED light indicates the device is charged above 20 percent.
• Yellow LED light indicates the power is under 20 percent Red LED light indicates the power is down to 10 percent or lower.
  When the LED light turns red, please stop riding.

RUNNING INDICATOR
When the operator triggers the foot mats, the Running Indicator LED will light up, which means that the system enters the running state.
When the system has an error during operation, the running LED light will turn red (for more details see Chapter 5: SAFE RIDING).

2-6.BLUETOOTH SPEAKER
The Kt has powerful built-in wireless speakers so you can play your music while riding.

PAIRING THE SPEAKER

Turn on your Kt and the speakers will “DingDong” to announce that it’s waiting for a Bluetooth” connection. This will indicate that your Kl speaker is now in pairing mode.

• Place the Kl and the Bluetooth” device to which you would like to pair it within the operating distance. We recommend keeping the two devices no further than 3 feet apart during pairing.
• Ensure Bluetooth” is enabled on your phone or music device. Refer to the manufacturer’s instructions for how to enable Bluetooth’ on your device.
• Once you have activated Bluetooth” on your device, select the option ” music from the list of available Bluetooth” devices.
• If required, enter the PIN code ‘000000″ and confirm the entry.
• The Kt will say “Paired” when successfully paired.
• Please note, that pairing mode on the Kl will last for two minutes. If no devices are paired after two minutes, the K1 speaker will automatically return to standby mode.
• If pairing is unsuccessful, turn off the Kl first and re-pair following the aforementioned steps.
• If your smartphone is out of range, or the battery is low on your KI, your speaker may disconnect from your smart device, and the K1 will say “Disconnected”. To reconnect, follow the aforementioned steps or recharge your hoverboard.

NOTE: Once you have paired the K1 speaker with a device, the speaker will remember this device and will pair automatically when the device’s Bluetooth“ is activated and in range. You do not need to re-pair any previously connected devices.

Your K1 can pair up to two multi-point devices. You can reconnect a previously paired device without going through the pairing or PIN process on up to two devices.

LISTENING TO MUSIC
Once the K1 speakers are paired to your device, you can stream music wirelessly to them. Select the track you wish to listen to on your device to listen via the speakers. All volume and track controls will be made using your music device. Should you encounter any problems while streaming, please refer to your device’s user manual.

2-7.SMARTPHONE APP

Your la is an App-enabled hoverboard that works with Apple Los and Android devices. Download the free T0M0100 app in order to access certain features of your K1 such as headlight colors and skill mode. using a QR code reader, hold the camera on your smartphone over the below QR code to download the TOMOLOO app. Feel free to search “TOMOLOO” in your device app.

http://www.tomoloo.com/a/2016/0325/309.html

DASHBOARD

• Bluetooth- To connect your K1 through Bluetooth on your smartphone, press “Connect”. If your 10 is already paired, this part of the screen will show “Connected” in blue.
• • Settings – Press the gear icon to adjust settings.
• Speed – The digital speedometer displays your speed in km per hour.
• Battery – The percentage displays the remaining battery life of your K1.
• Enjoy – Operation Tips.
• Sports – Enter the sports mode.
• Change Mode – Change Riding modes: Beginner, intermediate, Advanced.
• Standby – Turn on & Turn off the scooter.
• Customize Headlights – Change the colors and brightness of your LED Lights.
• Friends-This function can help you add your friends who also have “TOMOLOO hoverboard”, and you can review his/her recent games on/her page.
• Home – Back to home page.
• Challenge- You can PK your friends who also have “TOMOLOO hoverboard’ in this Mode, which can be set as you like.
• More – Display more information.

Bluetooth

Press ‘Bluetooth” to have the App begin scanning for any Tomoloo devices.

Your K1 must be powered on and your smartphone’s Bluetooth must be enabled. If your Bluetooth is not enabled on your smartphone, the App will remind you to enable it.

Once the scanning is complete, all detected Tomoloo scooters will display in a list. Press the select button to pair with a scooter and use the PIN ‘000000″. If multiple Tomoloo scooters appear, continue attempting to pair until your K1 is paired.
Once paired, the dashboard will display “Connected” in blue. You may now begin using the App with your

SETTINGS

Press the gear icon to change settings for your Kl.

• User Name – Customize the name for your K1 here. This name change will reflect in the dashboard and connect pages.
• Password – Customize the password for the Kl.
• Switch – Switch between MPH/KMH.
• Speed – Change the speed for the Kl.
• Force – Change the Driving Force.
• Sensitivity – Change the Sensitivity for the Kl. Set Dormant Shutdown Time -This setting allows you to set a time for your K1 to shut down automatically.

SKILL/SAFETY MODES

Cycle between 3 different skill modes. Each mode has a different top speed and sensitivity. The mode will only change if you are not using your K1 hoverboard.

• Low Mode – This mode is recommended for first-time TOMOLOO hoverboard users. In this mode, the sensitivity and top speed are very low.
• Normal Mode – This mode is recommended for users that are comfortable using TOMOLOO hoverboards but are not ready for full speed and extra sensitive controls. In this mode, the sensitivity and top speed are moderate.
• High Mode – This mode is recommended for everyday TOMOLOO hoverboard users. In this mode, the sensitivity and top speed are set to the maximum setting.

NOTE: Skill and safety mode must be selected. The TOMOLOO wilt default to ” Normal” mode if another mode is not selected.

HEADLIGHTS

Press “lights’ to set a custom color and brightness for your Kis Path illumination Lights. Simply choose your desired color from the color wheel. Slide the “Brightness” bar to adjust brightness. For your convenience, 4 basic colors have also been set as presets below the brightness bar.

2-8.CHARGING YOUR K1

• Ensure that the charging port is clean and dry.
• Open the charging port on your K1 hoverboard.
• Make sure that there is no dust, debris, or dirt inside the port.
• Plug the charger into a grounded wall outlet.
• Ensure the light on the charger is GREEN.
• Align and connect the 3-pin charging cable to the charging port of the Kt
• The charging indicator light on the charger change to Red, indicating that your device is now being charged.
• When the RED indicator light on your charger turns GREEN, then your device is fully charged.
• A full charge may take up to 3.5 hours.
• After fully charging your Kt, unplug the charger from your device and from the power outlet.

Chapter 3

RIDING YOUR K1

FAILURE TO FOLLOW ANY OF THE FOLLOWING SAFETY PRECAUTIONS MAY LEAD TO DAMAGE TO YOUR DEVICE, VOID YOUR MANUFACTURER’S WARRANTY, LEAD TO PROPERTY DAMAGE, CAUSE SERIOUS BODILY INJURY, OR MAY LEAD TO DEATH. Before using your device, be sure to familiarize yourself with the operating procedures.

3-1. OPERATING YOUR DEVICE

Make sure the device is fully charged before your initial use. For charging instructions, please follow the details under 2.8 CHARGING YOUR Kl. Stand directly behind your device and place one foot on the corresponding foot mat (as described in the diagram below).
Keep all your weight on your back foot still on the ground, otherwise, your device will begin to move, making it difficult to step evenly with your other foot. When you are ready, shift your weight to the foot already placed on the device and step on with your second foot quickly and evenly (as described in the diagram below).

NOTE: Stay relaxed and step on quickly, confidently, and evenly. Imagine climbing stairs, one foot, then the other. Look up once your feet are even.
Find your center of gravity. If your weight is distributed correctly on the foot mats and your center of gravity is level, you should be able to stand on your device just as if you were standing on the ground.

On average, it takes 3-5 minutes just to get comfortable standing on your device and maintaining proper balance. Having a spotter will help you feel more secure. The K1 is an incredibly intuitive device; it senses even the slightest bit of motion, so having any anxiety or reservation about stepping on may cause you to panic and trigger unwanted movement. When you first using your device, the fastest way to move in your desired direction is to focus in that direction. You will notice that just thinking about which way you would like to go will shift your center of gravity, and that subtle movement will propel you in that direction. Your center of gravity determines which direction you move, accelerate, decelerate, and come to a complete stop. As described in the diagram below, tilt your center of gravity in the direction you wish to move. To turn, focus on the direction you wish to turn and stay relaxed.

Do not turn suddenly while driving fast, do not ride sideways or turn on a slope. The self-balancing sensors may malfunction and risk your safety.
The more comfortable you get on the device, the easier you will maneuver. Remember at higher speeds, it is necessary to shift your weight to overcome the centrifugal force.
For bumps or uneven roads, bend your knees.

NOTE: Try staying relaxed and focus on finding your center of gravity to maintain full control of your K1 hoverboard.

Dismounting your device can be one of the easiest steps, yet when done incorrectly, may cause you to fall. To properly dismount, from a stopped position, lift one leg up and set your foot back down on the ground (STEPPING BACK). Then step off completely as described in the following diagram.

Before you get off, make sure that the hoverboard is stopped, then step off one foot at a time.

Make sure to lift your leg completely off the foot mat to clear the device when stepping back to dismount. Failure to do so may send the Kt into a tailspin.

NOTE: If the K1 is not placed on a level surface, an alarm will sound and the warning indicator will light up and prevent the K1 from moving. Place the K1 on a level surface and try riding it again.

3-2.WEIGHT AND SPEED LIMITATIONS

Speed and weight limits are set for your own safety. Please do not exceed the limits listed here in the manual.

• Maximum Weight: 265 lbs
• Minimum Weight: 44 lbs
• Maximum Speed: 9 mph

Overweight exertion on the device may increase the possibility of injury or product damage.

NOTE: To prevent injury, when max speed is reached, the K1 will beep to alert the user and tilt the rider slowly back.

3-3. OPERATING RANGE

Please notice that the Kl can travel a distance of up to 9 miles on a fully charged battery in ideal conditions. The following are some of the major factors that will affect the operating range of your device.

• Terrain: A smooth, flat surface will increase your driving distance while driving uphill, as well as rough or uneven terrain, will reduce your distance significantly.
• Weight: The weight of the user can affect driving distance, a lighter user will have further range than a heavier user.
• Ambient temperature: Please ride and store the device under recommended temperatures, which will increase driving distance: battery life, and overall performance of your device.
• Maintenance : Reasonable battery charging and maintenance will increase the distance. Overcharging the battery can reduce range.
• Speed and Driving Style: Maintaining a moderate speed will increase your distance: while traveling at high speeds for extended periods, frequent starts, stops, idling, along with frequent acceleration and deceleration will reduce your overall distance.

3-4.BALANCE & CALIBRATION

If your K1 is unbalanced, vibrating, or not turning properly, you can follow the below steps to calibrate it.

•First, place your K1 on a flat, horizontal surface, such as a floor or a table. The foot mats should be even with each other and not tilted forward or backward. Make sure the charger is not a plugin and the board is turned off. Press and hold the ON/OFF button for a total of 15 seconds. The hoverboard will turn on, lighting the battery indicator on the board.
•Turn the board off and then turn the board back on. Press the power button twice. Calibration will now be completed.

Chapter

4 PRODUCT WARNINGS

while riding your K1 hoverboard. if there is a system error or illegal operation performed with your device, the system cannot enter self-balancing mode, so the device will prompt the user in a variety of ways.

You will notice the Running indicator Light will turn RED and you will hear a beep sound alerting you to take precautions and cease operation.

the following are common occurrences where you will hear the safety Alerts. These notices should not be ignored, but appropriate action should be taken to correct any illegal operation, failure, or errors.

• Prohibited riding surfaces (uneven, too steep, unsafe, etc.)
• When you step on the device if the platform is tilted more than 10 degrees forward or backward.
• The battery voltage is too low.
• The device is still charging.
• During operation, the platform self-initiates to tilt due to excess speed.
• Overheating, or motor temperature is too high.
• The device has been rocking back and forth for over 30 seconds. -System enters protection mode, the alarm indicator will light up and the buzzer will alarm (this typically occurs when the battery is about to run out of power).
• If the platform is tilted forward or backward more than 15 degrees, the device will sound “Bibibi” like an alarm and can’t ride.
• If any or both tires are blocked, the device will stop after 10 seconds.
• When the battery level has depleted below protection mode, the device engine will power off after 15 seconds.
• While sustaining a high discharge current during use (such as driving up a steep slope for a long period of time), the device engine will power off after 15 seconds.

While riding your K1 hoverboard, if there is a system error or illegal operation performed with your device, the system cannot enter self-balancing mode, so the device will prompt the user in a variety of ways.

Chapter 5

SAFE RIDING

• Children, the elderly, and pregnant women should not ride the K1
• Do not ride after drinking or using drugs.
• Do not carry items when you are riding the device.
• Prior to each use, inspect the K1 and ensure it has been maintained correctly and is functioning properly.
• When riding the K1, please give way to pedestrians.
• Please be alert to things in front and far away from you. Keeping good vision will help you ride the K1 safely.
• Make sure your feet are always placed securely on the pads.
• The K1 cannot be ridden by two or more people, Only one person can operate the K1 at a time.
• The rider may not be less than 44 lbs, The K1 is unable to operate properly with such a rider, especially on downhill terrains where the driver will be unable to reduce speed or stop safety. When you ride the K1 along with other users, please keep a certain distance between each other to avoid a collision.
• You should always keep in mind that, while on the device, your height has increased several inches, Be careful when you pass through doorways.
• When turning, please maintain balance
• Do not allow distractions when riding the device, such as answering the phone or engaging in any other activities.
• Do not ride in the dark.
• Avoid riding particularly in the rain or on smooth surfaces, such as snow, ice, and other cannons fennec.
• Avoid riding particularly in the rain or on smooth surfaces, such as snow, ice, and other slippery floors.
• Do not ride on roads with obstacles (such as twigs, little, small stones, etc.).
• Avoid riding in narrow spaces or on steep slopes.
• Avoid riding around flammable gas, steam, liquid, or dust that could cause a fire.

Chapter 6

DAILY USE & MAINTAINS

Battery

Stop riding the K1 immediately if it displays low power.
No using the battery if it emits strange odors overheats or begins leaking, If the battery does leak, please do not touch any leaking materials, as the battery contains dangerous substances. Please do not open the battery and do not insert anything into the battery.
Only use the provided charger for the Kl. Do not charge the battery if it has over-discharged. It should be abandoned for your safety.

Modifications

Do not attempt to disassemble, modify, repair, or replace the K1 unit or any components of the unit. This will void any warranty and can lead to malfunctions that may cause personal injury.

Operation

Do not lift the Kt off of the ground while it is in operation and the wheels are in motion. This can result in freely spinning wheels, which may cause personal injury to yourself or others nearby, do not jump on or off the Kt, and do not jump while using the K1 always keep your feet firmly planted on the K1 while in operation, always check battery charge before using, do not ride when its battery is low, as indicated by a twinkling red light or a solid red light.

Maintains

• Keep the device away from heat sources, direct sunlight, humidity, and prolonged exposure to water.
• Do not operate the device if it has been exposed to water, moisture, or any other liquids to prevent electric shock, explosion, and/or injury to yourself and damage to the device.
• Do not use the device if it has been dropped or damaged in any way.
• Repairs to electrical equipment should only be performed by a qualified electrician. Improper repairs may place the user at serious risk.
• Do not puncture or harm the exterior surface of the product in any way.
• Keep the device free from dust, lint, etc.
• Do not use this device for anything other than its intended use or purpose. Doing so may damage the device.
• This product is a toy. Please keep care of children’s safety.
• Do not expose batteries, battery packs, or batteries installed to excessive heat, such as direct sunlight, or open flame.
• Wear safety protective gear when riding, like helmets, knee pads, wrist pads, etc.

Chapter 7

WARRANTY

TO QUALIFY FOR WARRANTY SERVICE

• This product cannot be used for rental or commercial use.
• This product cannot be used for competition.

LIMITATIONS OF LIABILITY

• This Limited 1 Year Warranty is non-transferable after the product’s initial sale.
• No unapproved modifications can be made to the product, its performance, or otherwise, in order for this Limited 1 Year Warranty to remain in effect.
• No reimbursement is provided for towing, loss of time, loss of use, inconvenience, or incidental or consequential damages.
• warranty is void if weather-related water damage is determined, Owner is responsible for storage and protection from the weather.
• TOMOLOO makes no warranty with respect to products or trade accessories not made by Tomoloo, including, but not limited to, motors, tires, wheels, and batteries, such products or trade accessories, such items being subject to the original manufacturer’s warranty, if any.
• This Limited 1 Year Warranty does not cover minor surface blemishes, rips, tears, or other cosmetic damages due to normal use, or other intentional or unintentional damage to the product.
• This Limited 1 Year Warranty will not cover any damage which results from the application of improper cleaners, solvents, or chemicals to the product, water damage, smoke or soot, or exposure to the saltwater, sea breeze, or salt.
• This Limited 1 Year Warranty will not cover any damage which results from aging, such as fading of paint, deterioration of plated surfaces, deterioration of rubber or plastics, or rusting.
• This Limited 1 Year Warranty does not cover improper repair or misdiagnoses of problems.
• This Limited 1 Year Warranty only covers parts due to manufacturer defects.
• Damage due to misuse or neglect, use other than as specified in the Owner’s Manual, or use under abnormal conditions are not covered by this Limited 1 Year Warranty.

OWNER’S WARRANTY RESPONSIBILITIES

As the device’s owner, you are responsible for the performance of the required maintenance, You may be denied a warranty claim solely because of your failure to ensure the performance of all scheduled maintenance, As the owner, you should be aware that you may be denied your warranty coverage if your device or a part has failed due to abuse, neglect, improper maintenance, or unapproved modifications, For any issue regarding your TOMOLOO product, contact email: service@tomoloo.com.

• Do not expose batteries, battery packs, or batteries installed to excessive heat, such as direct sunlight, or open flame.
• Wear safety protective gear when riding, like helmets, knee pads, wrist pads, etc.

WARRANTY INFORMATION

The 1-year limited warranty covers only parts due to manufacturer defects for one year from the date of purchase. The warranty is non-transferable from the original purchaser. The warranty does not cover minor surface blemishes, rips, tears, or other cosmetic damages due to normal use, or other intentional or unintentional damage to the device. The warranty does not cover any damage which results from the application of improper cleaners, solvents, or chemicals to the Product, water damage, smoke or soot, or exposure to the saltwater, sea breeze, or salt. The warranty does not cover improper repair or misdiagnoses of problems. If you believe your product needs any repair or you have questions, please contact our email: service@tomoloo.com.

*Please refer to the Product manual for full warranty coverage and specifications.

Print Name* —————————————
Address. ——————————————
E-mail:—————————————–
Phone:——————————————–
Amazon Order Number——————–

Your signature below acknowledges that you have read, fully understand, and accept this limited warranty agreement.

Signature: —————————–Date————–
Scan and email this warranty card to: service@tomoloo.com.
FB page: Tomoloo Shop
Tomoloo Electric Skateboard Scooter
Follow our FB page to become our VIP members!
Enjoy prime online customer and technical service!

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Shenzhen Tomoloo Technology industrial Co., Ltd

Address:5th floor, building 28, Yongfa Science park, Shajing street, Baoan District, Shenzhen
Web: www.tomolo.com
E-mail: service@tomolo.com
Shenzhen Tomoloo Technology industrial Co., Ltd supports After-Sell Service

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>