WINNERCOM CE NFC Touch Door Handle User Manual
- June 4, 2024
- Winnercom
Table of Contents
WINNERCOM CE NFC Touch Door Handle
Introduction
- Door handle Module (DHS)
- NFC & Capacitive Touch
- Pocket Light LED
- Hi-Speed CAN
The door handle module for Automotive has a NFC Reader and lock/Unlock
2Channel Capacitive touch Sensor function.
This module is installed inside of the door handle covers and will be attached
to the outside door panel.
This module is communicated with CAN network which enables to connect to the
car network to send the signal of lock and unlock of door and Pocket light LED
On/Off control.
It receives DC power from car battery at all time.
NFC DHS Design(BOM) & Application
CE – NFC Touch Door Handle
ITEMS
| SPECIFICATION
---|---
Size
|
125 x 18 x 20 mm (Length x Width x Height)
Color|
Black
Weight
| 53g +/- 2.2%
Waterproof|
Polyurethane full potting inside of module. Protective of humidity ,vibration, waterproof.
Material
|
Case : PA6+GF15% , ABS / PRESS : SPTE(Tin-Plating) / PCB : FR-4, 4Layer /
Foam Tape : EPDM/ FPCB : Polyimide film
NO| Lev| SUB| |
---|---|---|---|---
1| 1| CASE UPPER| | A6+GF15%
2| 2| ASELO1NER| | PC
3| 1| PCBASSY| TBD| FR-4
4| 1| FPCB| TBD|
5| 2| FOAM PAO LED| | EPDM
6| 2| CABLEASSY| | AVSS0.3SQ
7| 1| FOAMPADA| | POM
8| 1| FOAMPAOB| | POM
9| 1| ANT POTTING| | UE-917 A,B
10| 1| TAPE| –| PVC
Attentions
-
Please always mount the Door handle Module before power on the device to avoid circuit damage
-
Before power on the Module, check the power supply (Fig. 1)
-
Module Input Power connect to the connector (Fig. 1)
– Type : Spin Connector Sealed+’
– Maker & Part No.:. HKC0S-12737 SP Male Connector(Blue)
Pin#.⤾
| Name-| Description| In/ Ou t| Wire Color|
I/O Level
---|---|---|---|---|---
1⤾
| V Bat(+Vcc)⤾| Power Supply⤾| Power⤾| RED⤾| Battery +⤾
2⤾| L _CAN(L)⤾| CAN Low Signal⤾| I/O⤾| GREEN⤾|
2.5±TBD V⤾
3⤾
| TOUCH⤾| LOCK/ UNLOCK⤾| I/O⤾| GRAY⤾| LOCK/UN LOCK⤾
4⤾| L_CAN(H)⤾| CAN High Signal.:i| lfO.,| BLUE⤾|
2.5+ TBD V⤾
5⤾
| ⤾| ⤾| ⤾| ⤾| ⤾
6⤾| GND| Electric Ground⤾| Power⤾| BLACK⤾|
Gnd⤾
CAN(HI)CAN(LO)
Specifications
NFC Touch Data
Frequency Range| 13.56MHz for NFC
Operating Voltage| 9.0 ~ 16.0 [Vdc], Typical 12.0 [Vdc]
Current| Max 400mA @ Operation Mode
Operating Temp.| -30℃ ~ 75℃
Storage Temp.| -40℃ ~ 85℃
Symbol⎓| DC, IEC 60417-5031 (2002-10)
User Information and Instructions
FCC Part 15 Compliance information.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions :
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation
FCC Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
- This product is compliant with the essential requirements and other relevant provisions of the Directive 2014/53/EU.
- This product can be used in which EU members, in accordance with ArticleS10(10).
Manufacturer information
Manufacturer name
|
WINNERCOM Co., Ltd.
---|---
**** Address, City:
| HUMAX Village, 216, Hwangsaeul-ro, Bundang-Gu,
Seongnam-si, Gyeonggi-do, South KOREA 13595
Product name (type):|
Vehicle active antenna & Touch door
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>