SEALEY GSA6004.V2 3-4 Inch Sq Drive Composite Air Impact Wrench Twin Hammer Instruction Manual
- June 4, 2024
- SEALEY
Table of Contents
SEALEY GSA6004.V2 3-4 Inch Sq Drive Composite Air Impact Wrench Twin Hammer Instruction Manual
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT : PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
SAFETY
√ Follow all workshop safety rules, regulations, and conditions when using
wrench.
♦ WARNING! Disconnect from air supply before changing accessories or
servicing.
√ Maintain the wrench in good condition and replace any damaged or worn parts.
Use genuine parts only. Unauthorised parts may
be dangerous and will invalidate the warranty.
♦ WARNING! Check correct air pressure is maintained and not exceeded. We
recommend 90psi.
√ Keep air hose away from heat, oil and sharp edges. Check air hose for wear
before each use and ensure that all connections are
secure.
√ Only use impact sockets which are specifically designed for use with an
impact wrench.
√ Wear approved safety eye/face shield, ear defenders and hand protection.
♦ WARNING! Due to the possible presence of asbestos dust from brake
linings, when working around vehicle brake systems we recommend you wear
suitable respiratory protection.
√ Maintain correct balance and footing. Ensure the floor is not slippery and
wear non-slip shoes.
√ Keep children and non essential persons away from the working area.
⊗ DO NOT use the wrench for a task it is not designed to perform.
♦ WARNING! DO NOT use wrench if damaged or thought to be faulty.
Contact Service Agent.
⊗ DO NOT use wrench unless you have been instructed in its use by a
qualified person.
⊗ DO NOT carry the wrench by the air hose, or yank the hose from the air
supply.
⊗ DO NOT operate wrench if you are tired or under the influence of
alcohol, drugs or intoxicating medication.
⊗ DO NOT carry wrench with your hand on the power trigger in order to
avoid unintentional starting.
⊗ DO NOT direct air from the air hose at yourself or others.
√ When not in use disconnect from air supply and store in a safe, dry,
childproof location.
INTRODUCTION
Combination of composite materials, alloyed metals and twin hammer design result in a lightweight, durable and powerful air impact wrench. Soft grip handle with downward facing exhaust makes this wrench comfortable on the hands and ears and limits the circulation of brake dust on wheel applications. Fingertip power control and direction via lever on rear of wrench. Suitable for professional garage use.
SPECIFICATION
MODEL NO:……………………………………………..GSA6004.V2
Air Consumption: ………………………………………………… 30cfm
Breakaway Torque: ……………………………..1300lb.ft(1760Nm)
Drive: ……………………………………………………………….. 3/4”Sq
Free Speed: …………………………………………………….4200rpm
Inlet Size:…………………………………………………………3/8”BSP
Maximum Torque:………………………………..1180lb.ft(1600Nm)
Noise Power/Pressure: ……………………………….. 108/97dB(A)
Operating Pressure:……………………………………………..114psi
Vibration/Uncertainty:……………………………………. 7.7/2.4m/s²
PREPARATION
♦ WARNING! Ensure the air supply is clean and does not exceed 114psi while operating the wrench. Too high an air pressure and/or unclean air will shorten the product life due to excessive wear, and may be dangerous causing damage and/or personal injury
4.1. AIR SUPPLY
4.1.1. Ensure wrench air valve (or trigger) is in the “off” position before
connecting to the air supply.
4.1.2. You will require an air pressure of 114psi, and an air flow
according to specification.
4.1.3. Drain the compressor air tank daily. Water in the air line will
damage the wrench.
4.1.4. Clean compressor air inlet filter weekly. Recommended hook-up
procedure is shown in fig.1.
4.1.5. Line pressure should be increased to compensate for unusually long
air hoses (over 8 metres). The minimum hose diameter should
be 1/4” I.D. and fittings must have the same inside dimensions.
4.1.6. Keep hose away from heat, oil and sharp edges. Check hose for
wear, and make certain that all connections are secure.
4.2. COUPLINGS
Vibration may cause failure if a quick change coupling is connected directly to the wrench. To overcome this, connect a leader hose to the wrench. A quick change coupling may then be used to connect the leader hose to the air line recoil hose. See fig.1 & 2.
OPERATION
♦ WARNING! Ensure you read, understand and apply safety instructions before use.
5.1. Only use impact sockets which are specifically designed for use with
a impact wrench.
5.2. Connect the wrench to the air hose as in section 4.
5.3. Place the socket over the subject nut and depress the trigger to
operate the wrench.
5.4. To change direction turn the air regulator on the rear of the body
to the desired direction (fig.3).
5.5. The air flow may be regulated by adjusting the air regulator on the
rear of the body.
⊗ DO NOT use any additional force upon the wrench in order to remove a
nut.
⊗ DO NOT allow wrench to free run for an extended period of time as this
will reduce bearing life.
MAINTENANCE
♦ WARNING! Disconnect wrench from air supply before changing accessories,
servicing or performing maintenance. Replace or repair damaged parts. Use
genuine parts only. Unauthorised parts may be dangerous and will invalidate
the warranty.
⊗ DO NOT use worn, or damaged sockets.
6.1. If the air system does not have an oiler, lubricate the air wrench
daily with a few drops of Sealey air tool oil dripped into the air inlet.
6.2. Clean the wrench after use.
6.3. Loss of power or erratic action may be due to the following:
a) Excessive drain on the air line. Moisture or restriction in the air
pipe. Incorrect size or type of hose connectors. To remedy check the
air supply and follow instructions in section 4.
b) Grit or gum deposits in the wrench may also reduce performance. If
your model has an air strainer (located in the area of the air inlet), remove
the strainer and clean it. Flush the wrench out with gum solvent oil or an
equal mixture of SAE No 10 oil and paraffin.
Allow to dry before use.
6.4. For a full service contact your local Sealey service agent.
6.5. When not in use, disconnect from air supply, clean wrench and store
in a safe, dry, childproof location.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.
Note : It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice. Please note that other versions of this product are available.
If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk or
01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
01284 703534
© Jack Sealey Limited
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>