Cuisinart CGG-608 Professional Portable Gas Grill Installation Guide
- June 14, 2024
- Cuisinart
Table of Contents
GC-MAPLE RIDGE
Installation Guide
12WEB-MAPLER-10AR
https://www.gigabyte.com/Motherboard/GC-MAPLE-RIDGE-rev-10?m=ma#kf
For more product details, please visit GIGABYTE’s website.
GIGABYTE will reduce paper use in order to fulfill the responsibilities of a
global citizen. Also, to reduce the impacts on global warming, the packaging
materials of this product are recyclable and reusable. GIGABYTE works with you
to protect the environment.
Product Specification
Chip | Intel® JHL8540 Thunderbolt'” 4 Controller |
---|
Back Panel
Connectors| 1 x DisplayPort, supporting a maximum resolution of 8K
(7680×3840)@60 Hz (Note 1) (Note 2)
- Support for DisplayPort 1.4 version, HDCP 2.2, and HDR.
2 x Thunderbolt'” 4 out ports (Thunderbolt'” 4 Port 1/Thunderbolt’s 4 Port 2), supporting up to 40 Gbps bandwidth and a maximum display resolution of 8K (7680×3840)@60 Hz (Note 1) (Note 2)
2 x Mini-DisplayPort In ports (DP_IN11DP_IN2)
Internal Connectors| 2 x 6-pin PCIe power connectors
1 x USB 2.0/1.1 header
1 x 5-pin Thunderbolt” header
1 x 3-pin Thunderbolt” header
Interface| PCIe 3.0 interface (PCIe x4)
Data Transfer Rate| 40 Gbps Bi-directional per port
Supported Operating Systems| Support for Windows 10 (64-bit) with RS3 or later
Compatible Motherboards| Go to GIGABYTE’s website for the latest motherboard support list.
(Note 1) Actual resolutions supported are dependent on the graphics card being
used.
(Note 2) Due to hardware limitations, the DisplayPort connector, Thunderbolt’
4 connector 1, and Thunderbolt”‘ 4 connector 2 require signal input from
external devices and support up to two display outputs at a time.
Installing the GC-MAPLE RIDGE Add-in Card
|
---|---
Mini Display Port Cable x 2| USB 20711 Header Cable x1
|
Thunderbolt” Header Cable (5-in)x 1| Thunderbolt” Header Cable (3-pin) x 1
Step 1
Install the GC-MAPLE RIDGE add-in card in the PCIEX4 slot
Step2
‘Connect one end of the USB cable o the USB connector on the: GC-MAPLE RIDGE
card.
Step 3
Connect the other end of the USB cable o the F_USB connector on the
motherboard.
Step4:
Connect one end of the Thunderbolt™ header cable (5-pin) 1o the 5-pin
Thunderbolt™ header on the GC-MAPLE RIDGE adding card,
Step 5:
Connect the other end of the cable to the Thunderbolt” add-in card header 1 on
the motherboard,
(Note 1) The Thunderbolt™ header cable (5-pin) provided has two connectors. Choose the correct connector according o the Thunderbolt™ add-i card header on your motherboard,
Step 6:
Connect one end of the Thunderbolt” header cable (3-in) to the 3-pin
Thunderbolt™ header on the GC-MAPLE RIDGE ‘add-in card.
Step 7:
Connect the other end of the cable to the Thunderbolt™ add-in card header ®*3
on the motherboard.
(Note 2) Whether the connectoris supported depends on the motherboard
models
Step 8:
‘Connect the power cables from the power supply to the two PCle connectors
Step 9:
Follow the steps below to use the included Mini Display Port cable to connect
your graphics card 1o the GC-MAPLE RIDGE add-in card
9-1: Connect the cable from the Display Port In connector on the GC-MAPLE
RIDGE add-in card to the DisplayPort on your graphics card
9-2: Connect the Thunderbolt” device’s or DisplayPort monitor’s cable to the
Thunderbolt™ 4 connector on the GC-MAPLE RIDGE add-in card
- When connecting one DisplayPort monitor, please connect the Mini-DisplayPort cable to the DP IN 1 connector, then connect the monitor’s cable to the DisplayPort connector or Thunderbolt” 4 connector 1.
- When connecting two DisplayPort monitors, please connect one of the Mini-DisplayPort cables to the DPIN 1 connector and connect the monitor’s cable o the Display Port connector or Thunderbolt™ 4 connector Then connect the of her Mini-DisplayPort cable to the DP IN 2 connector and the monitor’s cable to Thunderbolt™ 4 connector 2.
- Make sure {0 update the motherboard BIOS to the ablest version.
Daisy-chaining Thunderbolt™ Enabled Devices-
Refer to the following for connecting Thunderbolt”-enabled devices in a daisy- chaining configuration. The following are single-port configurations. (Make sure the Thunderbolt”-enabled devices to be daisy-chained have both Thunderbolt™ in and out ports.)
Five Thunderbolt” devices and one dative DisplayPort monitor (Graphics card with DisplayPort require)
Five Thunderbolt” devices and three DisplayPort monitors (Graphics card with DisplayPort support is required)
Installing the Driver
After the computer starts, install the driver for the GC-MAPLE RIDGE add-in
card. Insert the included driver disc and follow the on-screen instructions to
install the driver.
Please visit GIGABYTE’s global website (http://www.gigabyte.com) and click
on Support & Downloads for the latest software driver.
Regulatory Notices
United States of America, Federal Communications Commission Statement
Supplier’s Declaration of Conformity
47 CFR § 2.1077 Compliance Information
Product Name: PCI Express add-on Card
Trade Name: GIGABYTE
Model Number: GC-MAPLE RIDGE
Responsible Party — U.S. Contact Information: G.B.T. Inc.
Address: 17358 Railroad street, City Of Industry, CA91748
Tel.: 1-626-854-9338
Internet contact information: https://Awww.gigabyte.com
FCC Compliance Statement:
This device complies with Part 15 of the FCC Rules, Subpart B,
Unintentional Radiators.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with
manufacturer’s instructions, may cause harmful interference to radio
communications, However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
tuming the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus set out in the Radio Interference Regulations
of the Canadian Department of Communications. This class B digital apparatus
complies with Canadian ICES-003.
European Union (EU) CE Declaration of Conformity
This device complies with the following directives: Electromagnetic
Compatibility Directive 2014/30/EU, Low-voltage Directive 2014/35/EU, RoHS
directive (recast) 2011/65/EU & the 2015/863 Statement. This product has been
tested and found to comply with all essential requirements of the Directives.
European Union (EU) RoHS (recast) Directive 2011/65/EU & the European
Commission Delegated Directive (EU) 2015/863 Statement
GIGABYTE products have not intended to add and safe from hazardous substances
(Cd, Pb, Hg, Cr+6, PBDE, PBB, DEHP, BBP, DBP and DIBP). The parts and
components have been carefully selected to meet RoHS requirement. Moreover, we
at GIGABYTE are continuing our efforts to develop products that do not use
intonationally banned toxic chemicals.
European Union (EU) Community Waste Electrical & Electronic Equipment (WEEE)
Directive Statement GIGABYTE will fulfill the national laws as interpreted
from the 2012/19/EU WEEE (Waste Electrical and Electronic Equipment) (recast)
directive. The WEEE Directive specifies the treatment, collection, recycling
and disposal of electric and electronic devices and their components. Under
the Directive, used equipment must be marked, collected separately, and
disposed of properly.
WEEE Symbol Statement
** The symbol shown below is on the product or on its packaging, which
indicates that this product must not be disposed of with other waste. Instead,
the device should be taken to the waste collection centers for activation of
the treatment, collection, recycling and disposal procedure.
For more information about where you can drop off your waste equipment for
recycling, please contact your local government office, your household waste
disposal service or where you purchased the product for details of
environmentally safe recycling.
End of Life Directives-Recycling
** The symbol shown below is on the product or on its packaging, which
indicates that this product must not be disposed of with other waste. Instead,
the device should be taken to the waste collection centers for activation of
the treatment, collection, recycling and disposal procedure.
Declaration of the Presence Condition of the Restricted Substances Marking
PCI Express add-on Card
Equipment name| GC-MAPLE RIDGE
Type designation (Type)
---|---
Parts| Restricted substances and its chemical symbols
(Pb)| (Hg)| (Cd)| (Cps)| (PBB)| (PBDE)
PCB| 0| 0| 0| 0| 0| 0
Shell| 0| 0| 0| 0| 0| 0
Chip and other Active components| —| 0| 0| 0| 0| 0
Components| —| 0| 0| 0| 0| 0
Connectors| —| 0| 0| 0| 0| 0
To Soldering metal| 0| 0| 0| 0| 0| 0
Cables| 0| 0| 0| 0| 0| 0
Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the
percentage content of the restricted substance exceeds the reference
percentage value of presence condition.
Note 2: “0” indicates that the percentage content of the restricted
substance does not exceed the percentage of reference value of presence.
Note 3: The “—” indicates that the restricted substance corresponds to
the exemption.
Administrative Measures for the Restricted Use of Hazardous Substances in
Electrical and Electronic Products (China RoHS Declaration)
Hazardous Substances Table
(Parts) | (Hazardous Substances) |
---|---|
(Pb) | (Hg) |
PCB | o |
Shell | o |
Chip and other Active components | o |
Passive Components | o |
Connectors | o |
Soldering metal | 0 |
Cables | o |
These tables are prepared in accordance with the provisions of SJT 11364
0 ; The content of such hazardous substance in all homogeneous materials of
such component is below the limit required by GB/T 26572.
x : The content of such hazardous substance in a certain homogeneous material
of such component is beyond the limit required by GB/T 26572.
Contact Us
GIGA-BYTE TECHNOLOGY CO., LTD.
Address: No.6, Baoding Rd., Xintian Dist., New Taipei City 231
TEL: +886-2-8912-4000,
FAX: +886-2-8912-4005
Tech, and Non-Tech, Support (Sales/Marketing) :
https://esupport.gigabyte.com
WEB address (English): https://www.gigabyte.com
WEB address (Chinese): https://www.gigabyte.com/tw
Copyright
© 2023 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their
respective owners.
Disclaimer
Information in this manual is protected by copyright laws and is the property
of GIGABYTE.
Changes to the specifications and features in this manual may be made by
GIGABYTE without prior notice.
No part of this manual may be reproduced, copied, translated, transmitted, or
published in any form or by any means without GIGABYTE’s prior written
permission.
For product-related information, check on our website at:
https://Avww.gigabyte.com