WINNERCOM SP2 PE NFC Touch Door Handle User Manual

June 4, 2024
Winnercom

WINNERCOM logo SP2 PE NFC Touch Door Handle
User Manual 

WINNERCOM SP2 PE NFC Touch Door Handle -

Introduction

  • Door handle Module (DHS
  • NFC & Capacitive Touch
  • Pocket Light LED
  • Hi-Speed CAN

The door handle module for Automotive has an NFC Reader and lock/Unlock 2Channel Capacitive touch Sensor function. This module is installed inside of the door handle overs and will be attached to the outside door panel.
This module is communicated with the CAN network which enables to connect to the car network to send the signal of lock and unlock of door and Pocket light LED On/Off control. It receives DC power from the car battery at all times.

WINNERCOM SP2 PE NFC Touch Door Handle - Fig1

NFC DHS Design(BOM) & Application

CE – NFC Touch Door Handle

Category Feature
System Micom

Cortex M0 @48MHz
RAM 32kB, ROM 256kB
NFC Processor| 3A LOGICS, TNR100
CAN Transceiver| NXP, TJA1044GTK/3, High-Speed CAN 500kbps
Mechanical Size| 125 x 17 x 15.5(h) [mm]   (Length x Width x Height)
Weight| TBD(g)
System Interface| NFC 13.56MHz NFC-A Type 4, Digital key 2.0
CAN Ver. 2.0 High Speed
Lock: direct cantact
Unlock: Handle Grip contact
Diagnostics| Battery Voltage: Under Voltage & Over Voltage
Internal Temperature: Over Heating
Pocket Lighting| N/A

WINNERCOM SP2 PE NFC Touch Door Handle - Fig2

NO| LEV| SUB| |
---|---|---|---|---
1| 1| CASE UPPER| | PBT+GF3096
2| 1| CASE LOWER+)| | PBT+GF30%43
3| 1| PCB ASSY| TBD| FR-443
4| 1| FPCB.| TBD43|
5| 2| CABLE ASSY| | AVSS 0350
6| 1| FOAM PAD A| | EPDM43
7| 1| FOAM PAD| | EPDM
8| 1| ANT POTTING| ESP 1101243| UE-917 A,B

Attention

  •  Please always mount the Door handle Module before powering on the device to avoid circuit damage
  • Before powering on the Module, check the power supply(Fig. 1)
  • Module Input Power connects to the connector(Fig. 1)

Pin #.| Name| Description| In/Out| Wire Color| I/O Level
---|---|---|---|---|---
1| V Bat(+Vcc)| Power Supply| Power| RED| Battery +
2| L_CAN(L)| CAN Low Signal| I/O| GREEN| 2.5±TBD V
3| TOUCH_1| LOCK| O| GRAY|
4| TOUCH_2| UNLOCK| O| PINK|
5| L_CAN(H)| CAN High Signal| I/O| BLUE| 2.5±TBD V
6| GND| Electric Ground| Power| BLACK| And

Specifications

NFC Touch Data:

Frequency Range 13.56MHz for NFC
Operating Voltage 9.0 ~ 16.0 [Vdc], Typical 12.0 [Vdc]
Current Max 400mA @ Operation Mode
Operating Temp. -30℃ ~ 75℃
Storage Temp. -40℃ ~ 85℃

WINNERCOM SP2 PE NFC Touch Door Handle - Fig4

[ System Block Diagram ]

user Information and Instructions

FCC Part 15 Compliance information:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions :
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Manufacturer information

**** Manufacturer name **** WINNERCOM Co., Ltd.
Address, City: **** HUMAX Village, 216, Hwangsaeul-ro, Bundang-Gu, Seongnam-

si, Gyeonggi-do, South KOREA 13595
Product name (type) :| Vehicle active antenna & Touch door

WINNERCOM logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals