POWERDRIVE PWD2000P 2000W Power Inverter Owner’s Manual

2000W Power Inverter

Owner’s Manual
PWD2000P

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

• This manual contains important safety and operating instructions for the 1 000W power inverter. It will help you use your inverter safely and effectively. Please carefully read and follow these instructions and precautions.
• Keep out of reach of children.
• Do not expose inverter to moisture or water.
• The use of an attachment is not recommended or sold by the unit manufacturer, as it may result in a risk of fire, electrical shock, or injury.
• Do not disassemble the unit.
• To reduce risk of electric shock, unplug unit before attempting any maintenance or cleaning. Turning off controls will not reduce this risk.
• For the most effective use, place the power inverter on a flat surface.
• Do not place the inverter on or near heating vents, radiators, other sources of heat, or flammable materials.
• Do not place the inverter in direct sunlight. The ideal air temperature for operation is between 32°F and 104°F.
• The power inverter should only be connected to a 12V battery or power supply. Do not attempt to connect the inverter to any other power source, including an AC power source. Connecting to a 6V or 16V battery will cause damage to the inverter.
• Do not use the inverter with a product that draws a higher wattage than the inverter can power, as this may cause damage to the inverter and product.

FEATURES

1. ON/OFF Switch
   Press and hold for 3 seconds to turn the inverter on and off.

2. 120V Standard AC Outlets (x4)

3. USB-A, USB-ce, with QC 3.0 Tech

4. Removable Remote Control Panel with LCD Screen

5. Positive Battery Cable Terminal (Red)

6. Negative Battery Cable Terminal (Black)

7. Ground Wire

8. High-speed Cooling Fans (x2)
   To keep the inverter cool, the fans turn on depending on temperature and load of the inverter. When the inverter is turned off, whether the fans run or not will depend on the temperature of the inverter.

CONNECTING INVERTER CABLES

IMPORTANT

• The inverter and power source must be in the OFF mode.
• Make sure to only connect your inverter to a 12V power supply. To avoid electrical shock, it is necessary to ground the inverter as well as the power source. The inverter should be grounded, using a 10 AWG copper wire (included).
• Do not turn on the inverter or the power source until the inverter and the power source are grounded .

TO GROUND THE INVERTER

1. Turn off and disconnect the inverter.
2. Locate the chassis ground screw on the back of the inverter.
3. Remove the outer nut and loosen the first locking washer.
4. Attach the grounding wire’s ring connector to the ground terminal of the inverter.
5. Tighten the locking washer securely. Then, replace the other nut and tighten it securely.
6. Attach the other end of the wire to a properly grounded location:
   Vehicle: Connect to the chassis, unpainted frame part, or engine block of the vehicle.

Fixed location: Connect to a ground rod or other appropriately rated ground.
CONNECTING INVERTER CABLES TO THE INVERTER

1. Locate the Positive and Negative terminals on the inverter.
2. From the Positive (red) and the Negative (black) terminals, remove the nut, split lock and flat washer.
3. Place the Positive (red) ring connector onto the Positive (red) inverter terminal. Place the NEGATIVE (black) ring connector onto the Negative (black) inverter terminal.
4. Place a flat washer and split lock on top of each ring connector. Put a nut over these and tighten.

OPERATING INSTRUCTIONS

1. Connect the inverter. (See Connecting Inverter Cables section).
2. Press and hold the On/Off button for 3 seconds to turn on the inverter.
3. The LCD backlight will turn to blue, and Input Volts and Output Watts will show on the LCD screen, indicating the inverter is receiving power.
4. Press and hold the On/Off button for 3 seconds to turn off the inverter. The internal speaker may make a brief “beep” sound. This is normal.
5. Make sure the device to be operated is turned off.
6. Plug the device into the inverter’s AC outlet.
7. Press and hold the On/Off button for 3 seconds to turn on the inverter.
8. Turn the device on.
9. To disconnect, reverse the above procedure.

NOTE: If more than one device is to be powered, start one device at a time, to avoid a power surge and overloading the inverter. The surge load of each device should not exceed the inverter’s continuous operation wattage rate.

IMPORTANT: Using the inverter with some rechargeable devices may damage the inverter and/or device. If you are using the inverter to operate a rechargeable device, monitor the temperature of the inverter for about 10 minutes. If the inverter becomes abnormally hot, disconnect it from the device immediately; do not use the device with the inverter.

Removable Faceplate Remote Control

• Remove the screws fixing the panel. Do not lose the screws
• Follow the diagram below to connect the panel and extension cord.

LCD SCREEN AND FAULT CODE

The LCD backlight turns blue automatically when the inverter is plugged into a 12V DC power source and is turned on.
Under the following conditions the LCD backlight will turn red, the fault code will be displayed on the screen, the alarm will sound, and the inverter will automatically turn itself off.

Low-Voltage Protection
When the power input from the vehicle’s battery drops to approximately 1 O.SV, the low-voltage alarm will sound. When the voltage goes down below 1 O VDC, the inverter
shuts off. Recharge or replace the battery.

High-Voltage Protection
When the power input from the vehicle’s battery exceeds 15V, high-voltage protection occurs.

Overload Protection
The continuous load demand from the equipment or device being operated exceeds the continuous load rating of the inverter. Use a higher capacity inverter or lower rated device.

Overheat Protection
The thermal resistor exceeds the set temperature. Allow the inverter to cool. Do not block the cooling slots or air flow over and through the inverter. Reduce the load on the inverter to the continuous rated output.

Short Circuit Protection
When the output is shorted, Short-Circuit Protection is activated.

RESET:
To reset after shutdown occurs, press and hold the On/Off button to turn off the inverter. Check the source of the problem and correct. Then, press and hold the On/Off
button to turn on the inverter.

About the Bluetooth® APP

THE MAIN FUNCTIONS

• Remote control signal range: best 10m/30ft;
• Real-time display of Input Voltage/ Output Voltage/Output Power/ Power source level;
• Display working hours, set auto-off time;
• Fault/ Protection display;
• Real-time monitor of the temperature, to avoid potential safety hazard;

HOW TO DOWNLOAD THE APP?
Android Phone:
Go to Google Play and search “PowerDrive Plu s”.
iPhone®:
Go to the App Store® and search “PowerDrive Plus”.
You can also scan the QR code below to download the APP.

https://qrco.de/bcYiIO

OPERATION INTRODUCTION

1. Make sure the inverter is connected to the battery.

2. Inverter Pairing: Place your phone close to the inverter (within 6.5ft) for first time use. Click **CIiek to Connect** to enter the Bluetooth search list.
   You will see “PowerDrive Plus”, and click to connect.
   • Once the connection is successful, the pairing is considered successful, and the APP will be automatically connected when it is used again. The paired inverter can be connected up to about 20ft in the absence of obstructions.
   • To reinstall the APP, some phone models need to be paired to the inverter again.
   

3. ON/OFF: Click the button at the bottom of the phone screen to control the ON and OFF of the inverter.
   

4. On & Off Timer: Click to set the startup or shutdown time in the pop-up box. It can be set for up to 30 days.
   After successfully set, a countdown will appear in the middle of the screen, and the Timing icon will change from white to purple. Click again to cancel the timer.
   • If you manually click the switch button after the timer is set, it will automatically cancel the set timer.
   • Disconnecting the inverter from the battery will cause timer failure.

5. Change the name of the inverter: The default name of the inverter is “PowerDrive Plus”. You can customize the name in the APP settings. The length of the name is
   1-16 characters. Click to enter the setting interface, click “Change Bluetooth Name” to enter the name, and click to confirm.
   • Some phones will disconnect briefly and then automatically reconnect.

6. Switch inverters: When you have more than one inverter, you may need to switch inverters. Click to enter the setting interface, click Switching Devices to enter the Bluetooth search interface, and click the name of the inverter with which you want to connect. If the inverter you want to connect to has not been paired, it will not appear in the search list. Please move your phone close to the inverter you want to connect to (within 6.5 ft) and click to refresh the list.

7. Device Management: Click to delete the paired inverter. When the list is emptied, it will automatically jump to the Bluetooth search interface.

8. Inverter Alarm: The fault alarm buzzer sound can be turned on or off on the inverter.

9. Phone Alarm: The fault alarm buzzer sound can be turned on or off on the APP.

10. Reset TEMP Unit: Switch the temperature unit.

PROTECTION AND ALARM
This interface will show up when the inverter enters protection mode. The APP will make an alarm sound. The alarm sound can be shut down in Settings. If you are not running the APP, or running it in the background, there will be no alarm sound.
Press and hold the On/Off button for 3 seconds to turn off the inverter.

POWER SOURCE

• Your average automobile battery at full charge will provide an ample power supply to the inverter when the engine is on.
• Keep the vehicle running at all times when using the inverter.
• The actual length of time the inverter will function depends on the age and condition of the battery and the power demand being placed by the device being operated with the inverter.
• When possible, recharge your batteries when they are not at less than 50% battery life. This gives the batteries a much longer life cycle than recharging when they are almost dead.

IMPORTANT:
The inverter draws low amperage from the battery when the inverter is turned on but no load is connected. To prevent battery discharge, turn the inverter off when not in use.

IF THE INVERTER’S FUSE BLOWS

• The fuse should not have to be replaced under normal operating conditions. A blown fuse is usually caused by reverse polarity or a short circuit within the device or equipment being operated.
• If a fuse does blow, take the inverter to a qualified technician for repair.

NOTE: do not attempt to service the inverter yourself. Dangerous electrical conditions exist even when the inverter is not connected to a battery.

MAINTENANCE AND STORAGE INSTRUCTIONS

• Before each use, ensure that all of the inverter’s components are in place and in good working condition.
• After use and before performing maintenance, unplug and disconnect the inverter.
• Use a clean, dry cloth to wipe external surfaces of the inverter’s case.
• Servicing does not require opening the unit, as there are no user-serviceable parts. All servicing should be performed by qualified service personnel.
• Store inside, in a cool, dry place, out of the reach of children.
• Recycle or properly dispose of internal electrical components.

TROUBLESHOOTING

connections.
Use a true RMS reading meter.
The LCD backlight is red.| Check the Fault Code on the LCD screen.| Recharge or replace the battery. Use a higher capacity inverter or decrease the load or device on the inverter. Allow inverter to cool. Check for adequate ventilation.
Reduce the load on the inverter to the rated continuous power output.
Device does not operate properly when first connected to the inverter.| The inverter may not have the required capacity to operate the device.| Press and hold the ON/OFF button to turn off and on, this will reset the inverter.

SPECIFICATIONS

USB-C PD Fast
Charging Port| 0.5 -15W. 5V, 0.1 – 3.0A 0.9 -18W, 9V, 0.1 – 2.0A 1.2 -18W, 12V, 0.1 – 1.5A
AC Output Socket| 4 Standard North American socket
Internal Fuse/ Replacement Fuse| 8*30A
Operating Temperature| 32°F – 104°F
Battery Low Alarm| 10.5±0.5V DC
Power Cable Length| 2 AWG 39.3″
Output Power Overload Shutdown Level| 2300±300
Dimensions| 14.54″x9.80″x4.25″
Net Weight| 8.91 lbs.

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on , the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The PowerDrive stylized design and RoadPro are registered trademarks owned by DAS Companies, Inc. and/or its affiliates. PowerDrive is a trademark owned by DAS Companies, Inc. and/or its affiliates. The BLUETOOTH® word mark and logos are registered trademarks owned by Bluetooth SIG , Inc. and any use of such marks by DAS
Companies, Inc. is under license. All other trademarks registered trademarks, copyrights and logos are the property of their respective owners. ©2021 DAS Companies, Inc. and/or affiliates.

Quick Tips

• Both positive and negative cables must be connected to a battery
• The negative cable should not be connected to the chassis
• The use of longer cables will require you to increase the gauge of the cables
• Please be sure to consult owner’s manual for proper cable sizing

DAS COMPANIES, INC. POWERDRIVE™ ONE YEAR LIMITED WARRANTY

This Limited Warranty covers this PowerDrive™ product. This product is warranted against defects in materials and workmanship for a period of ONE (1) YEAR from the date of original retail purchase (“Warranty Period”). This warranty extends only to the original purchaser and will end when the product is transferred to a subsequent owner. If a defect arises during the Warranty Period, DAS (PowerDrive), at its option and to the extent permitted by law will (1) replace the product with a new product as the same purchased or (2) exchange the product with a functionally equivalent product that is new. This warranty excludes damage resulting from misuse or abuse, accident, operation of the product not in accordance with the manuals or other included written instructions, modification of the product, attempted repair of the product, or as a result of an act of God or as a result of war or terrorist attack or other causes that are not defects in materials and workmanship.

Non-PowerDrive branded products/Third Party Products. This warranty does not apply to products that are not PowerDrive branded even if packaged or sold with PowerDrive products, nor does it apply to batteries or similar expendable parts or accessories.
TO THE EXTENT PERMITTED BY APPLICABLE LAW DAS (POWERDRIVE) IS NOT LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR SERVICE OF THE PRODUCT. THE WARRANTY AND REMEDIES DESCRIBED ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, REMEDIES, AND CONDITIONS, WHETHER ORAL, WRITTEN, EXPRESS, STATUTORY OR IMPLIED. TO THE EXTENT PERMITTED BY APPLICABLE LAW DAS (POWERDRIVE) DISCLAIMS ALL IMPLIED AND STATUTORY WARRANTIES, INCLUDING, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IF, AT ANY TIME, US FEDERAL LAW DOES NOT PERMIT IMPLIED WARRANTIES TO BE DISCLAIMED AND TO THE EXTENT SUCH IMPLIED WARRANTIES CANNOT BE DISCLAIMED, THEN SUCH
WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. Any recovery is limited to the value of the original purchase price. No other person is authorized to modify this limited warranty, and your seller is solely responsible for any other warranties.

Some states and countries do not allow limitations on how long an implied warranty lasts, or allow exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. For consumers, who are covered by consumer protection laws or regulations in their state or country of purchase or, if different, their state or country of residence, the benefits conferred by DAS’s One Year Limited Warranty are in addition to all rights and remedies conveyed by such consumer protection laws and regulations.

How to obtain Warranty Service? Within the first thirty (30) days after the original purchase, products must be returned to the dealer. After thirty (30) days and for up to one (1) year PowerDrive covers the product. Please fill in all areas of the Warranty Claim Form and submit. Replacement product for approved warranty claims will be shipped to the address you provide at no cost to you.
For customer support call 1-866-622-7979 Monday through Friday 8:00 am to 4:30 pm Eastern Time or send an email to support@roadprobrands.com.

Questions?
Visit our video library
www.powerdriveinverters.com
Call
1-866-622-7979
A representative is available
Monday – Friday (8:00AM – 4:30PM EST)
OR
Send us an email
support@roadprobrands.com

References

• PowerDrive - Power Inverters

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>