anslut 019930 Strip Light LED Instruction Manual

STRIP LIGHT LED
Instruction Manual
Item no. 019930

OPERATING INSTRUCTIONS
Important! Read the user instructions carefully before use. Save them for future reference. (Translation of the original instructions

SAFETY INSTRUCTIONS

• Read these instructions carefully before installation and use, and save them for future reference.
• The product is not dimmable.
• Disconnect the power supply before installation.
• The product is only intended for indoor use in dry areas. Damp areas and outdoor environments require products with a higher protection rating.
• Never modify the product or any of its parts in any way – the risk of personal injury or material damage.
• The product is intended for lights with 2-pin IEC-approved G13 standard sockets.
• The product should be installed by an authorized electrician in accordance with the relevant electrical safety regulations.

ELECTRICAL SAFETY!
New installations and extensions to existing systems should always be carried out by an authorized electrician. If you have the necessary experience and knowledge (otherwise contact an electrician), you can replace power switches and wall sockets, fit plugs, extension cords, and light sockets. Incorrect installation can result in fatal injury and the risk of fire.

SYMBOLS

| Read the instructions.
---|---
| The product is not dimmable.
| Approved in accordance with the relevant directives.
| Recycle discarded products in accordance with local regulations.

TECHNICAL DATA

INSTALLATION

FIG 1

|

FIG 2

AFTER INSTALLATION OF LIGHTS WITH CHOKE COIL
Conventional T8 strip light
S = Starter.

FIG. 3

LED strip light
Replace the starter with the LED fuse.
F = LED fuse.

FIG. 4

AFTER INSTALLATION OF LIGHTS WITH ELECTRONIC ACTUATOR
Conventional T8 strip light
A = Electronic actuator.

FIG. 5

LED strip light

1. Remove the electronic actuator (B) as shown in the figure below.
2. Connect a direct wire between pins 2 and 3 on the light.
3. Connect pin 1 to the mains phase (L) and pin 4 to neutral (N).
   B = Electronic actuator.

FIG. 6

PRODUCT INFORMATION SHEET

A light source connected to the mains supply or
light source not connected to mains supply:| MLS| Connected light source (CLS):| no
Color-tuneable light source:| no| Envelope:| –
High luminance light source:| no| |
Anti-glare shield:| no| Dimmable:| no
Product parameters
Parameter| Value| Parameter| Value

General product parameters:

Useful luminous flux (Φuse), indicating if it refers to the flux in a sphere (360°), in a wide cone (1200), or in a narrow cone (90°).| 2 000 in
Sphere (360°)| Correlated color temperature, rounded to the nearest 100 K, or the range of correlated color temperatures rounded to the nearest 100 K, can be set.| 3000
On-mode power (Pon), expressed in W.| 18,0| Standby power (Psb), expressed in W and
rounded to the second decimal.| 0,00
Networked standby power (Pnet) for CLS,
expressed in W and rounded to the second decimal.| –| Color rendering index, rounded to the nearest integer, or the range of CRI-values that can be set.| 80
Outer dimensions without
separate control gear, lighting
control parts and non-lighting
control parts, if any (millimeter).| Height| 28| Spectral power distribution in the range of 250 nm to 800 nm, at full load.| See the image on the last page
Width| 28
Depth| 1200
The claim of equivalent power (c)| –| If yes, equivalent power (W)| –
| | Chromaticity coordinates (x and y)| 0,440
0,400

Parameters for directional light sources:

Peak luminous intensity (cd)| | Beam angle in degrees, or the range of beam angles that can be set|
---|---|---|---
Parameters for LED and OLED light sources:
R9 color rendering index value| 3| Survival factor| 0,90
The lumen maintenance factor| 0,96| |
Parameters for LED and OLED mains light sources:
Displacement factor (cos φ1)| 0,90| Colour consistency in McAdam ellipses| 3
Claims that an LED light source replaces a
fluorescent light source without integrated
the ballast of a particular wattage.| _(b)| If yes then replacement claim (W)| –
Flicker metric (Pst LM)| 0,0| Stroboscopic effect metric (SVM)| 0,0

(a)”-”: not applicable;
(b)”-”: not applicable;

Jula reserves the right to make changes.
For the latest version of operating instructions, see www.jula.com
JULA AB, BOX 363, SE-532 24 SKARA
2022-01-12
© Jula AB

Documents / Resources

| anslut 019930 Strip Light LED [pdf] Instruction Manual
019930, Strip Light LED, Light LED, 019930, Strip Light
---|---

References

• Jula – products for home and garden

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>