Lumens LC100 Capture Vision System Installation Guide
- June 4, 2024
- Lumens
Table of Contents
LC100 Installation Guide
Introduction of Product Functions
1.1 Front View
1.2 Back View
1.3 Function Descriptions
| No. | Item | Function Descriptions | No. | Item | Function Descriptions |
|---|---|---|---|---|---|
| 1. | LCM | Display Menu and Information | 16 | DC IN 12V | DC 12 V power connector |
| 2. | Knob | LCM knob | 17 | Input1 | • HDMI Input 1 |
• 3G-SDI Input 1
• HDMI Passthrough
3| Record| Start/Stop recording
4| Stream| On/Off image streaming| 18| Input2| • HDMI Input
• 3G-SDI Inp 2
5| Scene| Switch templates| 19| Output| • PGM: Main screen output, display the
recording or streaming screen and layout
• Multiview: Operation interface output; display the settings menu and image
management
6| Power| On/Off the device power
7| Single Channel| Display a single-channel screen
8| PIP| Switch to PIP (picture in picture)
9| PBP| Switch to PBP (picture by picture)| 20| USB3.0 port| Supports the
following
devices:
• USB video/audio devices
• External storage disk
• LCKeyboard/mouse -RCO1 (optional)
controller
10| SWAP| Switch signal channels
11| USB3.0 port| for external storage disk
12| USB3.0 port| for external storage disk
13| USB2.0 port| Can connect to keyboard/mouse device operation menu| 21|
Ethernet| Connect to LAN
14| Factory Reset| Reset all configurations to factory default settings| 22|
RS-232/ RS-485 port| Connect to AV control equipment
15| Restart| Reboot the machine| 23| XLR audio in| Connect to a microphone or
audio mixer
| | | 24| Line In/ Out| Audio In/Out
Product connection diagram
Precautions Prior to Use
3.1 Lumens strongly recommends the use of a hard drive (not supplied) for
recording video and audio.
3.2 LC100 supports 2.5″/3.5″ SATA hard drives.
3.3 If no hard drive is installed, use a USB disk for external storage.
4.4 Fasten the hard disk to the metal plate with the provided screws (4 pcs).
A. 2.5″ SATA Hard Drive holes
B. 3.5″ SATA Hard Drive holes
- Do not over-tighten the screws to avoid damage to the hard drive. Only use the screws provided.
Hard drive installation steps
4.1 Remove the screws (5 pcs) on the top cover.
4.2 Loosen the following screws.
4.3 Attach your hard drive to the connection cable.
- Please make sure the port and the L-shaped slot of the cable are aligned before insertion. Do not force the connection to avoid damage to the port.
4.4 Fasten the hard disk to the metal plate with the provided screws (4 pcs).
A. 2.5″ SATA Hard Drive holes
B. 3.5″ SATA Hard Drive holes
- Do not over-tighten the screws to avoid damage to the hard drive. Only use the screws provided.
4.5 Lock the hard drive mounting plate in place and insert the connection cable.
4.6 Close the top cover to complete the installation.
4.7 Hard drive setting
After installation, you need to log in to the web page and click Information
to format the drive.
Storage Setting > Hard Disk
*Formatting the drive will erase all existing data on the disk
Real-time operation menu
Connect the HDMI1 MultiView output to a monitor to display the real-time operation menu
| No. | Item | Function Descriptions |
|---|---|---|
| 1 | Configuration | Configure the network settings and recording/streaming |
quality
2| Director| Creative control of video and audio inputs, and audio feeds.
Control recording and streaming and network video cameras
3| File Management| Transfer, upload, download, delete, and playback video
files
4| About| Display the current LC100 firmware version
5| Device IP| Displays the device’s network IP address.
Web Interface
6.1 Confirm the IP address of the device
Connect the LC100 to a router. Note the IP address of the device (visible in
the lower right corner of the HDMI MultiView output screen).
6.2 Input the device,s IP address into the web browser, e.g. 192.168.100.100.
6.3 Please enter your account/password to log in.
Web Interface
Thru the web interface users can access the File Manager, the MultiView
interface, and system settings.
Director Tab
Follow these steps to access the Director Tab
- On the MultiView interface, select Director
- Log in to the web page by entering the online Director Casting Account /Password (default setting: director/director)
www.MyLumens.com
Copyright © Lumens Digital Optics Inc. All rights reserved.