Muse Car Radio with Bluetooth & USB/SD User Manual

CAR RADIO WITH BLUETOOTH & USB/SD
M-195 BT

PRECAUTIONS

1. Do not attempt to modify the unit, modifying the unit may cause an accident.
2. Installation or servicing of the unit by persons without training and experience in electronic equipment and automotive accessories may be dangerous and could expose you to the risk of electric shock or other hazards.
3. Stop the vehicle before carrying out any operation that could interfere with your driving.
4. Keep the volume at a level which you could hear sounds from outside the vehicle.
5. Do not work in extremely high or low temperature. Be sure the temperature inside the vehicle is between +60°C and -10°C before turning on your unit.
6. When replacing the fuse(s), the replacement must be of the same amperage as shown on the fuse holder.
7. Do not block vents or radiator panels. Blocking them will cause heat to build up inside and may result in fire.
8. Using this unit without running the engine can result in battery drainage.
9. Use only in cars with a 12-volt negative ground.
10. After completing the installation or replacing the car battery, you need to RESET the unit before using it. Press RES button on the front panel with a pointed object (such as a ball-point pen) to reset the unit to its initial settings.

UNPACK YOUR UNIT

When you unpack your new car radio, make sure that you have removed all the accessories and information papers: Main unit
User manual Accessories:

CONNECTION

WIRING DIAGRAM

Caution!

• Make sure to connect the color-coded leads according to the diagram. Incorrect connections may cause the unit to malfunction or damage the vehicle’s electrical system.
• Make sure to connect the speaker (-) leads to the speaker (-) terminal. Never connect the left and right channel speaker cables to each other or to the vehicle body.
• Make sure all the connections are completely correct before turning on your unit.

 Do not connect the ignition wire (red) and the battery wire (yellow), it may cause a short circuit, even resulting in fire.

INSTALLATION

1. Insert the mounting sleeve to the car. Bend the claws outward for a tight fit, if necessary.
2. Combine mounting blot, steel bar, spring washer, and Hex nut. Then combine the unit and dashboard with a screw and plain washer.

LOCATION OF CONTROLS

1. Button: To turn unit on /off; To mute or restore sound
2. : To hang up the call; MODE button
3. VOL / SEL knob
4. RES button
5. LCD display
6. USB port
7. SD/MMC card slot
8. button
9. EQLOUD To select desired sound effects: FLAT /CLASSIC /ROCK / JAZZ / POP; LOUD: Loudness On/Off
10. To answer the phone/redial call; BAND button (To select band: FM1, FM2, FM3) and AMS button
11. button
12. Built-in microphone
13. 1 / button: To select preset channel 1 in radio mode. To start or pause playback.
14. 2 / INT button: To select preset channel 2 in radio mode/transfer call. To start/ cancel intro playback.
15. 3 / RPT button: To select preset channel 3 in radio mode. To repeat playback.
16. 4 / RDM button: To select preset channel 4 in radio mode. To start/ cancel random playback.
17. 5 / -10 button: To select preset channel 5 in radio mode; To skip backward 10 tracks (mp3 only18. 6 / +10 button: To select preset channel 6 in radio mode; To skip forward 10 tracks (mp3 only)
18. AUX jack

BASIC OPERATIONS

Turn on/off the unit
Press button to turn on the unit. Press and hold this button again to turn off the unit.
Selecting the mode
When the unit is on, press MODE button repeatedly to select different source modes: FM → USB → CARD → BT → AUX
Note: USB, CARD mode can not be selected if no such source was plugged in the unit.
Current time display
Press VOL button to display the current time when the unit is ON.
Adjust time:

1. When the unit is ON. Press and hold VOL to enter into setting mode.
2. Rotate the Volume knob anti-clockwise or clockwise to adjust the hour and minute value. It will confirm your setting if no key is pressed for 5 seconds.

Reset the unit
Operating the unit for the first time or after replacing the car battery, you must reset the unit. To set the unit to initial status, press the RES button on the front panel with a pointed object. When some errors occur in the display, you can also reset the unit, but it will erase the clock setting and some memorized functions.

SOUND FEATURES

Volume adjusting:
To increase or decrease the sound level, rotate VOL knob clockwise or anti- clockwise.
Muting the sound
When the unit is ON, press MUT to mute the sound. Press again to restore.
Using VOL/SEL knob to select sound feature
Repeatedly press VOL/SEL knob
To select the desired mode for sound setting in the following order: “BAS” (BASS) →“TRE” (Treble)→ “BAL” (Balance)→ “FAD” (Fader).
After selecting the desired mode, you can adjust the level by rotating the volume knob.
Preset equalizer (EQ)
When you are listening to pop music, classic music, or rock music, use the equalizer to adjust the sound quality. Press the EQ button repeatedly to select different equalizer modes in the following order: FLAT→ CLASSIC→ ROCK→ POP →EQ off.
Loudness on /off
Press and hold LOUD button until “LOUD ON” shows on display to activate the LOUDNESS function. Press and hold this button again until “LOUD OFF” to cancel the LOUDNESS function.

LISTENING TO THE RADIO

Selecting band
In tuner mode, repeatedly press BAND button to select bands in the following order: FM1→ FM2 → FM3.
Manual / automatic tuning
– Manual Search
Choose your radio station with or .
– Automatic search
Press and hold for few seconds or .
The automatic search locates strong stations. Citation with a weak signal can be set manually by repeatedly pressing or .
NOTE: During the search operation, the sound level is automatically muted.
Scanning and memorizing stations
– By BAND button (AMS)
In tuner mode, press and hold the BAND button for 3 seconds to start scanning for stations and store them automatically in memory. All preset stations are scrolled for a few seconds under your selected band. To remain on a station, press again the BAND button.
– By number button 1- 6

1. Tune to a station by or button.
2. Press and hold one of the 1- 6 number buttons for 2 seconds until LCD shows the corresponding number, which indicates that the station is stored in the corresponding number button.
3. Under radio mode, press 1- 6 Number buttons to listen to stored stations.
4. When you are listening to a station stored on a number button, press and hold another number button for more than 2 seconds to store the station on this number button.

Note: The unit can be stored up to 6 stations for each band.

DX/LOCAL
Repeatedly press VOL/SEL knob to select “DX/LOCAL” mode.
DX MODE: The weak signal out-of-town stations may be received.
LOCAL MODE: the strong signal local stations can be received.
STEREO/MONO
Repeatedly press VOL/SEL knob to select “STEREO/ MONO” mode. FM listening is generally done in Stereo mode. However, if the signal is weak or reception is not as good as you would like, switching to Mono mode usually improves the overall sound quality.

LISTENING TO USB/CARD

To insert a USB device (not included)
Connect your USB device to the USB port on the front panel. It will switch to “USB” mode and start playback automatically.

To insert a SD/ MMC card (not included)
Insert a SD/MMC card to the card slot. It will switch to “CARD” mode and start playback automatically.
Basic player functions
Play/pause: Press the button to pause playback. Press again to resume playback.
Skip/fast search:

1. Press to skip forward to next song.
2. Press button to play the previous song.
3. Press -10 or +10 to skip to 10 songs backward or forward.
4. Long press -10 or +10 to select the previous folder or next folder in MP3 mode.

Intro scan:
Press INT button to play first 10 seconds of each track, and “INT ON” appears on display. Press again to cancel and “INT OFF” appears.
Repeat:
Press RPT button repeatedly to select a play mode: RPT ONE, RPT DIR, RPT OFF
Random playback:
Press RDM button to play all files in random order, and “RDM ON” appears on display. Press again to cancel this function and “RDM OFF” appears.
Note:

• There are many USB devices or SD/SDHC/MMC cards on the market. We cannot guarantee to support all different models. Please try another USB device or SD/ MMC card if your device is not supported.
• The unit might not support all the multimedia files stored in SD/ MMC card or USB because it includes some special playback procedure that might not be compatible with the procedure of this unit.

LISTENING TO AUXILIARY SOURCE

1. Connect your auxiliary source (e.g. mp3 player) to the AUX IN jack.
2. Press the button to turn the unit on.
3. Press MODE to select AUX mode.
4. Start playback from your auxiliary source.
5. Adjust the volume to the desired level.
6. Disconnect your auxiliary source from the Aux-in jack, press the MODE button to select another source.

BLUETOOTH FUNCTION

The Bluetooth ® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by New One S.A.S is under license. Other trademarks and trade names are those of their respective owners.

• Before operating the Bluetooth function, make sure your mobile phone supports Bluetooth function.
• For different models of mobile phones, Bluetooth emissive power has some differences. To get the best conversation quality, it is recommended that the distance between the mobile phone and the unit is within 3 meters (Max.10 meters).
• Don’t put any metal object or any obstacle between the path of the mobile phone and the unit.

PAIRING

1. When the unit is ON, press the MODE button repeatedly to select BT.
2. Turn on the Bluetooth function of your mobile phone. (Please refer to the instruction manual of your mobile phone on how to operate Bluetooth.)
3. Select the item of searching the Bluetooth device and enter it. Your mobile phone starts to search for Bluetooth devices within range (10 meters). Select this car radio “M-195 BT” and confirm it, then you are asked to input a 4-digit password that is “0000”. Enter the password and confirm it. Then the LCD of the car audio system will display “BT READY”.

Noted: If you have made Bluetooth connectivity before, a list of the previous search results is displayed. Select “M-195 BT” and confirm.

Answer/ Reject a call
When there is an incoming call, the phone number appears on display.
Press to answer a call, the talking time will appear on the display. Rotate the volume knob to adjust the BT VOL.
Press to reject a coming call.

Dialing a Phone Call
To redial the last number retained in the memory of the mobile phone, press the button twice.
Notes:

• The re-dialing function is unavailable if there is no dial record feature in your mobile phone.
• If the conversation is not clear, try to move closer to the microphone.

Transfer the call between mobile phone and the unit
During the talking mode, you can press “2” button to transfer the phone call between the mobile phone and the unit. When making an outgoing call, it’s not possible to transfer if the call is not being answered yet.

BLUETOOTH AUDIO

The unit supports Bluetooth audio functions. If your mobile phone can play stereo music, when pairing successfully, press MODE to access Bluetooth audio mode, “MEDIA” appears on display.
The audio file in your mobile phone starts to play via the car radio.
Play/pause: Press the button to pause playback. Press again to resume playback.
Skip to next or previous track:

1. Press to skip forward to the next track.
2. Press to play the previous track.

Notes:
– This system will not operate or may operate improperly with some Bluetooth mobile phones/audio players.
– There are many mobile phones in the market. We cannot guarantee the compatibility of all mobile phones together with the unit.
– If you found the conversation is not clear, try to move closer to the microphone.
Hereby, NEW ONE S.A.S, declares that this MUSE M-195 BT is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. The declaration of conformity may be consulted at www.muse- europe.com

MAINTENANCE

Precaution
– Clean the front panel with a soft cloth or damp chamois leather. Never use solvents.
– Do not expose to rain or water;
– Do not drop or apply shock.
– Make sure that you keep your set away from high temperatures.
– The use of apparatus in moderate climates.
– Do not be exposed to dripping or splashing, and that no object filled with liquids, such as vases, shall be placed on the apparatus.
– No naked flame sources such as lighted candles should be placed on the apparatus.
Replacing the Fuse
Make sure the amperage matches the specified value when replacing the fuses. If the fuse is blown, check the power connection and replace with a new one. If the same problem occurs, it would be subjected to the malfunction in-house. In such cases, please consult the nearest service dealer.

TROUBLESHOOTING GUIDE

connected to the car accessory circuits, but the engine is not moving, switch the ignition key to “ACC’.
The fuse is blown.| Replace the fuse.
No sound.| Volume is in a minimum.| Adjust volume to the desired level.
The wiring is not properly connected.| Check wiring connection.
The operation keys do not work.| The built-in microcomputer is not operating properly.| Press the RES button.
Front panel is not properly fixed into its place.
The radio does not work. The automatic radio station selection does not work.| The antenna cable is not connected.| Insert the antenna cable firmly.
The signals are too weak.| Select a station manually.

SPECIFICATIONS

General

Power Requirement| 12V DC (11-16V allowable)
Load Impedance| 4 ohms
Max. Power Output| 40W x4
Tone Controls| ±10 dB
Bass at 100 Hz
Treble at 10 kHz
Dimensions| Approx. 58 x 140 x 180 (h / w / l)
Weight Approx.| Approx. 0.550kg
FM Tuner Section
Tuning Range| 87.5-108(MHz)
IF Range| 10.7MHz
Usable Sensitivity (-30dB)| 12dBuV
Signal-to-noise Ratio| 50dB
Stereo Separation| 30dB (1 kHz)
USB/MP3 Section
Signal-to-noise Ratio| 60 dB
Separation| 50 dB
Distortion| <0.5%
Frequency Response| 20 – 20000Hz

Note:
Due to continuous product improvement, specifications and design are subject to change without prior notice.
WARNINGS

ATTENTION: To reduce the risk of electric shock, do not remove the cover. There are no user-serviceable parts inside the unit. Refer all servicing to qualified personnel.
The lightning flash with an arrowhead symbol within the triangle is a warning sign alerting the user of “dangerous voltage” inside the unit.
** The exclamation point within the triangle is a warning sign alerting the user of important instructions.
WARNING –** To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
If at any time in the future you should need to dispose of this product please note that Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. (Waste Electrical and Electronic Equipment Directive)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>