TOOLOTS KD-1400W Sweeper Instruction Manual

October 30, 2023
TOOLOTS

**TOOLOTS KD-1400W Sweeper Instruction Manual

**

Pay attention to!!!

  1. this machine is used only as a cleaning tool, and for any other purpose than the instructions stated in this guide, we shall not be liable for any damage resulting therefrom.
  2. This sweeper can clean the general garbage,should not clean the rope,toxic and harmful, high temperature debris, so as not to wrap, burning the main brush and side brush, so that it can not work normally.
  3. The machine shall only be used by authorized and trained personnel.
  4. When the machine stops working, it must be parked on a flat ground.
  5. Irpersonnel and children should be removed from the scene when the machine is used.
  6. The power key switch must be closed when opening the hood or machine for maintenance and maintenance.A power cable needs to be removed during mechanical maintenance.
  7. When transporting the sweeper, confirm that it has been securely tied to the carrier.
  8. Make sure that the battery is in the ventilated place when charging. IF the sweeper stops working or runs when the underpressure alarm occurs, the battery should be charged in time to extend the battery life.
  9. When completing the work, unout the key in time to avoid the unrecognized use of the sweeper.
Sweeper operation instructions

Turn on the power switch to confirm that the machine power is normal; the normal voltage is 48 to 54 V, and 48 volts. Do not use power loss. The battery must be charged as soon as possible. It is forbidden to store it for a long time without electricity.

Do not use equipment to clean wires or packaging belts, otherwise ensure that the main brush shaft is cleaned every half a month.

To achieve the best cleaning effect, please adjust the driving speed according to the actual situation. When the machine works, the working speed should be controlled within 5 km/h. Do not pass through the areas of deep water.

During the operation, it is best to dust the filter at a specified time interval (25‐30 minutes.) The dust time is to clean the dustbin to achieve the best cleaning effect.

Use the main brush for large area ground cleaning, use the edge brush only at the edge position

Do not let the brush rotate when the machine does not move on. The height of the obstacle should not exceed 50mm. When passing, the large garbage baffle must  be raised slowly and carefully driving over the obstacle. Fixed obstacle height exceeding 50mm can only be passed or bypassed using appropriate slopes.

After each use, the requirements to clean up the bin, it is strictly prohibited to accumulate to quickly over the bin volume to clean up.

The filter is cleaned once a week, remove the filter and clean it with an airgun or a brush. The filter is not clean for a long time, which affects the cleaning effect. If the sweeper is not used for a long time, please place the sweeper on a flat ground, and charge the battery about once every two months.

This machine is an electric product, so it is strictly forbidden to wash the car body whit water.

Equipment is used to clean the indoor/outdoor floor is not allowed for modification, do not use the machine as means of transport.

No cleaning/absorption of items burning or not extinguished. When the user takes the start key form the machine.

Do not touch the heating part, such as a running motor, to avoid burns

Only cross slopes below 20%or there is a risk of turning over

When connecting the battery charger to the main circuit, ensure the voltage and frequency.

When the key switch is in the on (ON) position, do not connect and remove the battery, do not put tools or similar items on the battery, there is a risk of short circuit or even explosion.

Check the tightness of the brake regularly

The machine is limited to personnel trained by the Company, and all consequences caused by the use shall be borne by other personnel.

Introduction of the sweeper parameters

content parameter unit
voltage 48 V
Clean the width 55 in
Main brush width 27.5 in
Brush the diameter 20 in
Working efficiency 64585-96878 sqft/h
Working time 4 h
Dumpster capacity 40 gal
Walking motor 1.6 hp
Rolling brush motor 1.07 hp
Brush the motor 0.13 hp
Speed of travel 0-12 Km/h
Battery capacity 150 ah
Water tank capacity 21 gal
Vehicle weight 1211 LB
Product size 735555 in

The adjustment of brush

The main function of edge brush is to use its own rotation to collect the garbage on both side to the middle, from the main brush to the dustbin. The advantage of edge brush is that it can sweep out the garbage at the corners and dead corners, and improve the cleaning efficiency.

Under normal work conditions, the brush should be slightly bent from the ground to contact with the ground, the brush is too low from the ground,easy to cause load heat overload, will accelerate the wear of the bristles. Side brush height adjustment method: adjust the nut 1 shown in the figure, so that the brush slightly contacts the ground from the ground height.

The side brush height adjustment as shown in the figure, both sides need to be adjusted, adjust the length of the screw to achieve the height of the main brush from the ground. Normal cleaning side brush contact with the ground 3‐5mm, not too close to the ground.

Adjustment of main brush

The width of the main brush touching the ground should be 2‐4mm. When the main brush touches the ground too wide, the normal operation of the machine will be affected, and the spare parts are easy to heat up, reducing the service life of the machine.

The main brush height adjustment as shown in the figure, life the shell, adjust the length of the screw out to achieve the height of the main brush off the ground. Normal clean the main brush contact with the ground 3‐5mm, not tooclose the ground

The replacement of the main brush

Filter cleaning and replacement

The garbage filter element needs to be checked regularly. When the filter cannot be cleaned or damaged, it needs to be replaced.

As shown in the following figure, clean the filter element steps:

  1. Unplug the dust motor plug;
  2. Unscrew the 4 hand screw nuts;
  3. Unplug the filter element to clean the filter element. Replace the filter element by removing the six inner hexagonal screws in the illustration.
question cause handle

The sweeper leaks too
large leaves or large
particles of garbage| Work too fast| Reduce the speed of
working
The brush pressure is too
small| Adjust the pressure of the
brush
The bristles are deformed
or wrapped with filaments| Remove the winding
material
The sweeper left dust or
dust on the floor from the
side baffle| The filter is blocked| Clean the filter
Fender damage| Check the retaining cover
and replace it if damaged
Cleaning is not thorough,
leaving scraps of paper,
leaves or other rubbish| The front skin lift agency
has no work| Repair the winding
material
The brush wears too fast| The brush was pressed too
tight| Reduce brush pressure
The floor is very rough
Too much noise at work| The bristles are wound
with filaments| Remove the winding
material
Bearing bad| Replace the bearing
The brush is over pressed| Reduce the pressure
The brush does not rotate
while working| The transmission belt is
damaged| Replace the belt
Brush and fan motor are
not working| Blown fuse| Change the fuse
The car cannot move
forward and go backward| Damaged pedal governor| Replace the governor
Brake pedal position fault| Check the brake pedalreset intact
Brake switch fails| Replace the brake switch
Controller damage| Replace the controller
The battery cannot be
charged| The charger is not
energized| Check the charger input
power supply
The battery burned| Replace the battery
charger| Check the charger for any
output
Battery terminal is loose| Check and tighten the
battery terminals
The battery discharges too
fast| Insufficient charging time| Increase charging time
| The battery burned| Replace the battery
| Charger damage| Replace the charger
The electric dust device isnot working| Switch bad| Change the switch
| The fuse burned| Change the fuse
| The motor load is too large| Check and reduce the load
| Motor damage| Replace the motor
| Bearing wear and tear| Replace the bearing
The brush can worknormally and cannot drivenormally| Problems withcontroller,fuses,drivemotor,governor,brakeswitch| Check the input/outputvoltage,indicatorlamp,fuse,drive motor,andconnection line

Thank you very much for choosing our product. Before the sweeper is put into use, please read the instructions carefully and strictly follow them to achieve the best cleaning effect and extend the life of the machine. Please contact us for your comments and suggestions. We warmly and quickly serve you.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals