ECTIVE MSP 60 SUNDOCK Solar Module Instruction Manual
- June 10, 2024
- ECTIVE
Table of Contents
ECTIVE MSP 60 SUNDOCK Solar Module
ECTIVE SUNDOCK MSP
Product Information
The ECTIVE SUNDOCK MSP is a monocrystalline solar module that is designed to generate electricity from sunlight. It is available in three different models: MSP 60 SUNDOCK, MSP 100 SUNDOCK, and MSP 120 SUNDOCK. Each model has a different power rating, ranging from 100Wp to 180Wp. The ECTIVE SUNDOCK MSP has a nominal voltage of UMPP (V) and a nominal current of IMPP (A). The power tolerance of the module is +/- 3%. The module has a weight of 3.8kg to 9.5kg depending on the model. The module comes with a fuse that has a rating of 10A to 20A depending on the model.
Product Usage Instructions
The ECTIVE SUNDOCK MSP is designed to be used with a solar charge controller, a battery, and a load. The following are the operating instructions:
- Connect the solar charge controller to the solar module using the provided cables.
- Connect the battery to the solar charge controller using the provided cables.
- Connect the load to the solar charge controller using the provided cables.
- Ensure that the solar module is exposed to sunlight.
- The LED on the solar charge controller will turn red if there is an open circuit or if the load voltage is below 14V. The LED will turn off if the load voltage is above 14V.
Note: The ECTIVE SUNDOCK MSP should only be installed and used by qualified professionals who have experience working with electrical systems.
Welcome!
Thank you for choosing the ECTIVE SUNDOCK solar module!
Please read this manual carefully before installing and using the device. Also
make sure to read and follow the instructions for any charge controller you
connect to the solar module.
ECTIVE stands for power supply solutions at an unbeatable price-performance
ratio.
Explore our brand and products at ECTIVE.DE
Safety Information
- Do not use the solar module if it has been damaged or if it does not operate correctly.
- Do not allow water to enter any connected solar charge controller.
- Prevent sharp objects from damaging the surface of the solar module.
- Ensure that any connections to batteries are correct and secure; prevent short circuits.
- The solar module contains no user-serviceable parts. Do not disassemble or attempt to repair the solar module.
- Do not touch any exposed wires, terminals or connections.
- Due to the sophisticated electronic components contained, prevent water or moisture from entering the solar module.
Overview
| MSP 60 SUNDOCK | MSP 100 SUNDOCK | MSP 120 SUNDOCK | MSP 180 SUNDOCK | |
|---|---|---|---|---|
| Rated power (Wp) | 60 | 100 | 120 | 180 |
| Rated voltage UMPP (V) | 19.8 | 22.0 | 19.8 | 19.8 |
| Rated current IMPP (A) | 3.03 | 4.55 | 6.06 | 9.10 |
| Performance tolerance | +/− 3% | +/− 3% | +/− 3% | +/− 3% |
| Open-circuit voltage | 23.4 | 26.0 | 23.4 | 23.4 |
| Short-circuit current | 3.21 | 4.82 | 6.42 | 9.65 |
| Dimensions (mm) (L×W×H) | 530×873×25 | 675×1040×25 | 530×1593×25 | 525×2225×25 |
| Dimensions (mm) (folded) | 530×440×45 | 675×520×45 | 530×440×45 | 525×440×45 |
| Weight (kg) | 2.5 | 3.8 | 4.8 | 9.5 |
| Fuse (A) | 7.5 | 10 | 15 | 20 |
Scope of delivery
-
1× ECTIVE SUNDOCK MSP solar module with Small Anderson plug socket
-
Cable connecting battery (with fuse):
MSP 60, 100,120: 1× 3m 14 AWG Alligator Clip-Small Anderson
MSP 180: 1× 3m 12 AWG Alligator Clip-Small Anderson -
Cable for connecting MPPT solar charge controller:
MSP 60, 100,120: 2× 0.3m 14 AWG flat receptacle-Small Anderson MSP 180: 2× 0.3m 12 AWG flat receptacle-Small Anderson
Operating Instructions
Setup and operation
Find a clear, sunlit area without hanging branches or other obstacles.
Unfold the module and make sure the solar panel faces in the direction of the
sun. Adjusting the orientation of the solar module to face the sun maximizes
the power output of the panel.
Connect the module to the appropriate inputs of a compatible solar charge
controller. Connect the battery you want to charge, or any devices you want
power, to the correct outputs of the charge controller.
Make sure all connections are secure and avoid any short circuits.
Compatible batteries and devices
Using an appropriate char controller, this solar module can be used to charge
or provide power to the following batteries and devices:
- sealed lead-acid batteries
- colloidal lead-acid batteries
- flooded lead-acid batteries
- lithium batteries
- mobile phones
- tablets
- navigation systems, etc.
Integrated USB ports
ECTIVE SUNDOCK solar modules feature two USB ports with an output of 5V and
2A, which you can use to power or charge small, compatible devices such mobile
phones and digital cameras.
Indicator LED
The integrated LED provides information on the status of the solar module:
| LED is green (charging) | Open circuit: > 14V | Load: > 14V / < 14V, >0.5mA |
|---|---|---|
| LED is red (not charging) | Open circuit: < 14V | Load: < 14V / < 14V, <0.5mA |
| LED flashing red | Low light level. | |
| LED flashing red/green | Over current. (Over current protection: 9A) |
Please note:
When the LED flashes, please disconnect the solar panel and DC load and check
for any short circuits.
If the LED is red when the solar module is connected to a load, disconnect the
load or place the solar panel in direct sunlight.
Cleaning the surface of the solar module
Remove any dust and dirt from the solar module’s surface using a soft brush
and then wipe the surface clean with a damp cloth. Any guano should be removed
as soon as possible to prevent a negative impact on the solar module’s
performance.
Troubleshooting
If the battery is not being charged, even though the module is directly facing
the sun, there may be an issue with the connections. Make sure the solar panel
is correctly connected and no connections are reversed. Also, the solar charge
controller may be damaged and may need to be replaced.
Always read and follow the instructions for any solar charge controller you
connect to the solar module.
Recommended Solar Charge Controller
A solar charge controller is required in order to use this solar module to
charge batteries or power devices.
For use with ECTIVE MSP solar modules, we recommend our ECTIVE MPPT SC 20
Silent solar charge controller. This high-quality, fully automatic device uses
MPPT technology to maximize charging
efficieny: charging times and energy loss due to inefficiencies are reduced.
In addition to offering these advantages over traditional controllers, the ECTIVE MPPT SC 20 Silent is is exceptionally user-friendly. It requires no maintenance and offers various protective features to protect your batteries and equiment from damage. Learn more about our solar charge controllers on our website: ective.de
Recycling
Please recycle or dispose of the packaging material for this product. The
german Electronic Equipment Act (ElektroG) regulates how to place electronic
devices on the market, how to recycle and dispose of them.
When decommissioning the device, please contact the nearest recycling centre
or point of sale in order to get information about the disposal regulations.
eine Marke der / a brand of batterium GmbH
Robert-Bosch-Straße 1 71691 Freiberg am Neckar Germany
Tel.: +49 7141 1410870
ECTIVE.DE
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>