RYDEEN BSS2LPB Microwave Radar Blind Spots System Owner’s Manual
- June 10, 2024
- RYDEEN
Table of Contents
- RYDEEN BSS2LPB Microwave Radar Blind Spots System
- Product Information
- Product Usage Instructions
- Product Technical Specification
- Items list
- Technical Specification
- Installation Diagram
- Wire Connection Diagram
- Installation Guide
- Alert Conditions
- How does it alert?
- Troubleshooting
- Technical Support Contact Info.
- Limited Warranty
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
RYDEEN BSS2LPB Microwave Radar Blind Spots System
Product Information
The BSS2LPB Microwave Radar Blind Spots System Version 1.2 is a device that helps drivers detect blind spots while driving. The system comes with a main unit, main harness & extension cable, BSS BAR with two sensors built inside, LED indicators, LED indicator housing, GPS antenna, buzzer, velcro, 3M tape, screws, L-tooling, and wedges for installation. The system has a detection range of 1ft-50ft and a speed range of 0.5mph-137mph. It operates at an operating voltage of 9-18V and a working temperature of -20 ~ +70 degrees.
Product Usage Instructions
Installation Guide
- Step 1: Install the BSS BAR on the bottom or top of the license plate as per your preference.
- Step 2: Using the voltage multi-meter, locate the left and right isolated turn signal trigger wires behind the tail lamp. Once verified, connect the left and right signal wires of the BSS2LPB wire harness to the correct signal wires.
- Step 3: Place the LED indicators where they are visible for the driver, ideally on the A-pillar.
- Step 4: Install the speaker in a location where it is not obstructed by any panels inside the vehicle.
- Step 5: Tuck the wires neatly to hide and prevent wire pinch.
- Step 6: Install the GPS in a location where it is not obstructed by any panels inside the vehicle.
Product Technical Specification
- Detection Range: 1ft-50ft
- Speed Range: 0.5mph-137mph
- Speed Accuracy: < 0.5mph
- Speed Restriction: 4 options – 5mph, 10mph, 15mph, and 20mph (default is 20mph)
- Direction of Movement: Approached or overtaken by vehicles
- Operating Voltage: 9-18V
- Waterproof: Radars – IP67 / Cables – NOT waterproof
- Working Current: < 100mA
- Working Temperature: -20 ~ +70 degrees
Items list
Tools for installation: insulation tape; multi-meter; screwdriver; cleaning cloth; tape; M6 screws; L-tooling; Wedge.
Technical Specification
Detection Range | 52 degrees (Horizontal) |
---|---|
Speed Range | 0.5mph 137mph |
Speed Accuracy | < 0.5mph |
Speed Restriction
|
- The GPS need to detect+20mph to activate the sensors. (there are 4 speed restriction option: 5mph, 10mph, 15mph, 20mph. Default is 20mph).
- Please see below (from 1-4 switch, it could control 4 speed restriction) Switch 1=5mph, Switch 2=10mph, Switch 3=15mph, Switch 4=20mph default is 20mph.
- If no GPS signal is detected or satellites not found, the system will be actived at any speed
Direction of Movement| Approached or overtaken by vehicles
Detection Range| 1ft-50ft
Operating Voltage| 9—18V
Waterproof| Radars: IP67 / Cables: NOT waterproof
Working Current| < 100mA
Working Temperature| -20℃ ~ + 70℃
Installation Diagram
Wire Connection Diagram
- wire connection for BSS BAR installed on bottom of license plate
Installation Guide
- BSS BAR installation
- Two installation options available: the BSS BAR could be installed on bottom or on top of the license plate. the default is installed on the bottom of license plate.
- Step 1: Install the BSS BAR on the bottom of the license plate (see Fig.1).
- The BSS BAR also could be installed on top of the license plate (see Fig.2).
- Installation of the left/right turn signal.
- Step 2: Using the voltage Multi-meter, locate the left and right isolated turn signal trigger wires behind the tail lamp. Once verified, connect the left and right signal wires of the BSS2LPB wire harness to the correct signal wires (see Fig.3, Fig.4, Fig.5).
- LED indicator installation:
- Step 3: Place the LED indicators where it is visible for the driver. Ideally on the A-pillar (see Fig.6, Fig.7).
- Speaker location:
- Step 4: While installing the speaker, make sure it is not obstructed by any panels inside the vehicle (see Fig.8).
- Step 5: Tuck the wires neatly to hide and prevent wire pinch.
- Step 6: While installing the GPS, make sure it is not obstructed by any panels inside the vehicle (see Fig.9).
Alert Conditions
- When the vehicle is on, the system would start detecting objects in the blind area in the lane next to and behind the vehicle 50 feet (see Fig.10).
- When vehicles are approaching and their speed is faster than our own speed.
How does it alert?
- Blind detection on right side:
- R-LED indicator will be activated and indicator will light up when there is an object approaching to the right side blind area of your vehicle at speed over 20 mph (see Fig.10).
- If the right turn signal of your vehicle is triggered at the same time, the R-LED indicator will blink and the buzzer will be beeping as well (with the same frequency) at speed over 20 mph.
- Blind detection on left side:
- L-LED indicator will be activated and indicator will light up when there is an object approaching to the left side blind area of your vehicle at speed over 20 mph (see Fig.10).
- If the left turn signal of your vehicle is triggered at the same time, the L-LED indicator will be blink and the buzzer will be beeping as well (with the same frequency) at speed over 20 mph.
- The LED and buzzer will not light up (no activity) if there is no object approaching to the blind area of your vehicle.
- When in reverse, the buzzer speaker will beep to give cross traffic notification and the LED will indicate the direction of incoming vehicles (or objects) approaching. Notifications will not alert, for standing objects under 5mph reverse speed.
Troubleshooting
NO. | Issue | Reason | Solution |
---|---|---|---|
1 | LED light does not work | Incorrect connection or pins not making contact |
Check the harness and make sure connection is correct
LED light is broken| Replace LED light
2
| ****
Opposite LED indicator
| Microwave sensor or LED indicators are plugged in to the opposite connector|
Make sure RED is driver side and YELLOW is passenger side.
3
| ****
Buzzer does not work
| Wrong connection or pins not making contact| ****
Check the harness and make sure the connection is correct
Defective buzzer speaker| Replace buzzer
4| Sensors or GPS does not work| Sensors or GPS module are covered by the
metal bumper or other metal| Find the best location where the GPS antenna
cannot be blocked by any metal
5| Unit does not work after GPS is connected| Blind spot system does not
trigger the sensors if the speed is less than 20mph| Normal behavior in this
case. The GPS needs to detect +20mph to trigger the sensors
Technical Support Contact Info.
- Telephone: 1-877-777-8811 (within USA only)
- Email: tech1@rydeenmobile.com
- Web Address: www.rydeenmobile.com
Limited Warranty
Rydeen North America Inc. (a manufacturer of “Rydeen” products) warrants this product (BSS2LPB) only to the original purchaser as described following:
Warranty Coverage
This warranty covers all defects in material and workmanship except as specified below.
- Installation by anyone other than an authorized Rydeen Mobile Retailer may void the warranty.
- Any products distributed outside of the USA by Rydeen North America Inc. (Rydeen) or which is not purchased in the USA or Canada.
- Any product(s) which are purchased from an unauthorized retailer (in-store or online).
- Any products in which the serial number label or the model number label are removed, torn, modified or replicated.
- Any damage defects or malfunctions resulting from any of following:
- When defect occurs during shipment of product (freight carrier’s responsibility).
- Installation or removal of product.
- Accidents, act of nature, misuse, abuse, neglect, unauthorized product modification or failure to follow product owner’s manual instructions.
- Any repair or attempt to repair without RYDEEN authorization.
- Any other cause which is not related to product defect.
- Any cosmetic damages due to normal wear and tear.
- Any consumable items (such as fuse or batteries).
If any problems develop with your Rydeen products during or after the Limited Warranty Period, or if you have any questions regarding the operation or installation of the product, you should contact your Rydeen retailer.
To Obtain Warranty Service
If warranty service is required for your Rydeen product:
- Please call Rydeen Customer Service Department at 1-877-777-8811 (within the USA only), Monday–Friday between 9:00 AM to 4:00 PM Pacific Standard time and obtain a Return Authorization Number (“RA”) Number.
- Please pay for any shipping charge to Rydeen Customer Service Department. Rydeen will pay the return shipping charge, if the repair or service was performed during the warranty period. Rydeen will ship freight collect (Recipient is responsible for shipping charge) if Rydeen determine the service was performed outside of warranty period or exclusions described above. Rydeen will not accept warranty service requests from outside of the U.S.A. even if product was purchased in the USA.
- Please include a copy of your original purchase receipt including Rydeen Product model number, purchase date, retailer name/address and a RA Number whenever your product is sent for warranty service.
- Shipping address for Rydeen Customer Service Department is following: Rydeen North America Inc 2701 Plaza Del Amo, Unit 705, Torrance, California 90503, USA
Contacts
- rydeenmobile.com
- Rydeen North America Inc. Dba
- Rydeen Mobile Electronics
- 2701 Plaza Del Amo, Suite 705, Torrance, California 90503
- Phone: 1-877-777-8811
- Fax: 1-310-943-3778
Copyright © 2017 Rydeen North America Inc. All Rights Reserved.
RYDEEN ® is a registered trademark of Rydeen North America Inc.
These materials are protected by copyright law and international treaties. Any
unauthorized use, reproduction or distribution of these materials, or any
portion herein, will result in severe civil and criminal penalties and fines.
Violators will be prosecuted to the fullest extent of the law.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>