RYDEEN PV8-A Ultra Bright HD Rearview Mirror Owner’s Manual

RYDEEN PV8-A Ultra Bright HD Rearview Mirror

INSTALLATION PRECAUTIONS/NOTES

CAUTION:
DO NOT USE EXCESSIVE FORCE WHEN REMOVING MIRROR FROM WINDSHIELD. THE WINDSHIELD BUTTON MAY SEPARATE FROM THE WINDSHIELD OR THE
WINDSHIELD MAY BREAK.

• Do not use excessive force if removal of OE mirror button is necessary.
• Do not route wiring over sharp metal edges or allow to be pinched behind trim to avoid causing an electrical short or break in the wire.
• Manufacturer/distributor is not responsible for installation-related damage to vehicle.

Screw mount mirror removal procedure (Toyota, Nissan, Select Ford, Select Honda, Chrysler, GM):
Note that there are several versions of screw mount mirror systems!!!

• Using a Philips screwdriver or #20 torx bit, loosen the screw in the base of the mirror.
• After loosening screw, gently lift upward to slide mirror off of mirror mount.

Wedge mount mirror removal procedure (Ford):

• Using a small 1/8″ flat-blade screwdriver, insert the flat end into opening at the bottom of the mirror mount at the windshield.
• Slide the screwdriver into the center of the mirror mount until resistance is felt.
• Gently apply a small amount of additional upward force to lift away locking spring in the mount.
• While still applying upward pressure with the screwdriver, grasp the mirror bracket and wiggle side to side. Lift mirror up toward the headliner and off the windshield mount button.

Camlock/Twist Mount Mirror Removal procedure (VW, Most Honda, Most Hyundai):

• Grasp the base of the mirror.
• Rotate 90 degrees left or right. Remove mirror for twist mount.
• Slide mirror downward toward dash to remove for camlock mount.

NOTE: If the Rydeen Mirror does not fit the mount on your windshield, it is possible that one of our adapter plates may. It may also be possible that the mirror button will have to be replaced with one that is compatible with the Rydeen Mirror (example: Fords built prior to 1996). If you need information concerning one of Rydeen adapter plates or a mirror mounting kit, please call 1-877-777-8811 and speak with Rydeen sales or technical support agent.

Mounting the D-TAB on the glass windshield

• Park the car in a place where the temperature is somewhere between 50 and 75 degrees.
• If it’s in winter, find a heated garage to work inside.
• If it’s in summer, pick a nice day, with moderate temperature and low humidity.
• If you are in a high humidity area, pull car into the shade, and use your front defroster with A/C (turn on to “high”). This will help cool the glass and drop the humidity to a proper point.
• If the glass is too hot, the adhesive will set with less strength. So make sure to wait for the car to cool down in a shade or inside garage.
• We recommend following manufacturers’ products. These products have a limited shelf life, especially if not stored properly. Similarly, don’t buy one and keep it stashed in your
  hot glove box — it won’t last.

Permatex® Extreme Rearview Mirror Professional Strength Adhesive
http://www.permatex.com/products/Automotive/specialized_maintenance_repair/auto_glass_lens_repair/Permatex_Extreme_Rearview_Mirror_Professional_Strength_Adhesive.htm

Permatex® Professional Strength Rearview Mirror Adhesive
http://www.permatex.com/products/Automotive/specialized_maintenance_repair/auto_glass_lens_repair/Permatex_Professional_Strenath_Rearview_Mirror_Adhesive.htm

LOCTITE® REAR VIEW MIRROR REPAIR ADHESIVE
http://www.loctiteproducts.com/p/mech_spec_mirror/overview/Loctite-Rear-View- Mirror-Repair-Adhesive.htm

Manufacturer distributor is not responsible for installation-related damage to vehicle.

1. Mark the position of the button on the outside of the windshield with a grease pencil.

2. Clean, clean, clean the glass and button with the cleaner pad in the installation kit.

3. The kit has a special cleaner/primer pad saturated with a solution that does double duty.
   A solvent cleans the glass and also acts as a catalyst for setting the adhesive later. Scrub the glass and the button without touching the surface with your fingers. You don’t want to leave any oily fingerprints behind — they will prevent full adhesion.

4. Open the small vial of adhesive with a razor blade and squeeze a single, generous drop out onto the face of the button.

5. Please aim precisely, and press the button onto the glass.

You get only ONE CHANCE, so we really do mean aim precisely. Hold the button in place for 1 minute, using moderate pressure. Full curing is done within 24 hours, it is ideal to allow ample time for the curing process, or the adhesive will separate from the glass.
NOTE: If you need more information concerning one of Rydeen mirror mounting kit, please call 1-877-777-8811 and speak with Rydeen sales or technical support agent.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>