MAGMATIC RSS160 Sidewinder High Velocity CO2 Simulator Fog Machine with LED Lights User Manual
- June 6, 2024
- MAGMATIC
Table of Contents
SIDEWINDER
User Manual
US SKU#: RSS160
UPC#: 810008261538
©2021 MAGMATIC EFFECTS all rights reserved. Information, specifications,
diagrams, images, and instructions herein are subject to change without
notice. MAGMATIC EFFECTS logo and identifying product names and numbers herein
are trademarks of MAGMATIC EFFECTS. Copyright protection claimed includes all
forms and matters of copyrightable materials and information now allowed by
statutory or judicial law or hereinafter granted. Product names used in this
document may be trademarks or registered trademarks of their respective
companies and are hereby acknowledged. All non-MAGMATIC brands and product
names are trademarks or registered trademarks of their respective companies.
MAGMATIC EFFECTS and all affiliated companies hereby disclaim any and all
liabilities for property, equipment, building, and electrical damages,
injuries to any persons, and direct or indirect economic loss associated with
the use or reliance of any information contained within this document, and/or
as a result of the improper, unsafe, insufficient and negligent assembly,
installation, rigging, and operation of this product.
MAGMATIC EFFECTS | 6122 S. Eastern Ave. | Los Angeles, CA. 90040
323-582-3322 |
323-832-9142 fax |
www.elationlighting.com |
sales@magmaticeffects.com
Elation Professional B.V. | Junostraat 2 | 6468 EW Kerkrade, The
Netherlands
+31 45 546 85 66 | +31 45 546 85 96 fax |
www.elationlighting.eu |
info@elationlighting.eu
Elation Professional Mexico | AC Santa Ana 30 | Parque Industrial Lerma,
Lerma, Mexico 52000
+52 728-282-7070
DOCUMENT VERSION
Due to additional product features and/or enhancements, an updated version of
this document may be available online.
Please check www.elationlighting.com for the
latest revision/update of this manual before beginning installation and/or
programming.
Date| Document
Version| Software
Version| DMX Channel Mode| Notes
---|---|---|---|---
10/15/20| 1.0| 1.0| 1 / 4 / 7 Channels| Initial Release
12/11/20| 2.0| N/C| N/C| Updated Dimensional Drawings & Specifications
7/12/21| 3.0| N/C| N/C| Updated Operation & Specifications
GENERAL INFORMATION
INTRODUCTION
Please read and understand the instructions in this manual carefully and
thoroughly before attempting to operate this device. These instructions
contain important safety and use information.
This product is intended to be used by professionally trained personnel
only and is not suitable for private use.
UNPACKING
Every device has been thoroughly tested and has been shipped in perfect
operating condition. Carefully check the shipping carton for damage that may
have occurred during shipping. If the carton is damaged, carefully inspect the
device for damage, and be sure all accessories necessary to install and
operate the device have arrived intact. In the event that damage has been
found or parts are missing, please contact our customer support team for
further instructions. Please do not return this device to your dealer without
first contacting customer support. Please do not discard the shipping carton
in the trash. Please recycle whenever possible.
BOX CONTENTS
Twist-locking power cable (x1)
CUSTOMER SUPPORT
Contact MAGMATIC customer service for any product-related service and support
needs.
Also visit forums.elationlighting.com
with questions, comments, or suggestions.
ELATION SERVICE USA – Monday – Friday 8:00am to 4:30pm PST
323-582-3322 | Fax
323-832-9142 |
sales@magmaticeffects.com
ELATION SERVICE EUROPE – Monday – Friday 08:30 to 17:00 CET
Voice: +31 45 546 85 63 | Fax: +31 45 546 85 96 |
support@elationlighting.eu
REPLACEMENT PARTS: Please visit
parts.elationlighting.com
IMPORTANT NOTICE!
THERE ARE NO USER-SERVICEABLE PARTS INSIDE THIS UNIT. DO NOT ATTEMPT ANY
REPAIRS YOURSELF. DOING SO WILL VOID YOUR MANUFACTURER’S WARRANTY. DAMAGES
RESULTING FROM MODIFICATIONS TO THIS FIXTURE AND/OR THE DISREGARD OF SAFETY
INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID THE MANUFACTURER’S WARRANTY
AND ARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/OR REPAIRS.
NEVER POINT OR AIM A FOG MACHINE TOWARDS PEOPLE OR THEIR CLOTHING. THIS UNIT
EMITS HOT VAPOR AND SHOULD BE USED WITH THE SAME CARE THAT YOU WOULD OBSERVE
WHEN USING AN ELECTRIC KETTLE OR IRON.
LIMITED WARRANTY (USA ONLY)
A. Magmatic Effects hereby warrants, to the original purchaser, Magmatic
products to be free of manufacturing defects in material and workmanship for a
period of two years (730 days) from the original date of purchase. This
warranty excludes discharge lamps and all product accessories. This warranty
shall be valid only if the product is purchased within the United States of
America, including possessions and territories. It is the owner’s
responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service, send the product only to the Magmatic Effects
factory. All shipping charges must be pre-paid. If the requested repairs or
service (including parts replacement) are within the terms of this warranty,
Magmatic Effects will pay return shipping charges only to a designated point
within the United States. If any product is sent, it must be shipped in its
original package and packaging material. No accessories should be shipped with
the product. If any accessories are shipped with the product, Magmatic Effects
shall have no liability whatsoever for loss and/or damage to any such
accessories, nor for the safe return thereof.
C. This warranty is void if the product serial number and/or labels are
altered or removed; if the product is modified in any manner which Magmatic
Effects concludes, after inspection, affects the reliability of the product;
if the product has been repaired or serviced by anyone other than the Magmatic
Effects factory unless prior written authorization was issued to purchaser by
Magmatic Effects; if the product is damaged because not properly maintained as
set forth in the product instructions, guidelines and/or user manual.
D. This is not a service contract, and this warranty does not include any
maintenance, cleaning or periodic check-up. During the periods as specified
above, Magmatic Effects will replace defective parts at its expense and will
absorb all expenses for warranty service and repair labor by reason of defects
in material or workmanship. The sole responsibility of Magmatic Effects under
this warranty shall be limited to the repair of the product, or replacement
thereof, including parts, at the sole discretion of Magmatic Effects. All
products covered by this warranty were manufactured after January 1, 1990, and
bear identifying marks to that effect.
E. Magmatic Effects reserves the right to make changes in design and/or
performance improvements upon its products without any obligation to include
these changes in any products theretofore manufactured.
F. No warranty, whether expressed or implied, is given or made with
respect to any accessory supplied with the products described above. Except to
the extent prohibited by applicable law, all implied warranties made by
Magmatic Effects in connection with this product, including warranties of
merchantability or fitness, are limited in duration to the warranty periods
set forth above. And no warranties, whether expressed or implied, including
warranties of merchantability or fitness, shall apply to this product after
said periods have expired. The consumer’s and/or dealer’s sole remedy shall be
such repair or replacement as is expressly provided above; and under no
circumstances shall Magmatic Effects be liable for any loss and/or damage,
direct and/or consequential, arising out of the use of, and/or the inability
to use, this product.
G. This warranty is the only written warranty applicable to Magmatic
Effects products and supersedes all prior warranties and written descriptions
of warranty terms and conditions heretofore published.
WARRANTY RETURNS (USA ONLY)
To obtain warranty service, a Return Material Authorization (RMA) number must
first be obtained from MAGMATIC. It is the Customer’s responsibility to
provide product proof of purchase and serial number by acceptable evidence
such as an invoice copy or an approved MAGMATIC Extended Warranty Certificate
(“EWC”) and any relevant maintenance records at the time warranty service is
sought. Failure to provide acceptable evidence of product proof of purchase or
EWC and any relevant maintenance records may be cause for denial of warranty
service.
Products returned for warranty service must be sent without any accessories
(i.e., power, data, and safety cables, brackets, clamps, rigging hardware,
frost filters, gel frames, barn doors, lenses, hoses, nozzles, rack mounting
hardware, etc.), must be boxed using the original and/or suitable packaging
materials (double-box and foam) that provides ample product protection for
ground and/or air freight transit, and must be shipped freight pre-paid and
insured to MAGMATIC in Los Angeles, CA or a MAGMATIC Authorized Service
Center. The RMA number must be clearly written on the outside of the return
box, and a brief description of the problem and the RMA number must be
documented and included in the box.
Products returned for warranty service without an RMA number clearly marked on
the outside of the package will be refused and returned to the shipper at the
Customer’s expense. Products returned for warranty service, which are received
damaged due to inadequate and/or improper packaging and/or due to damage
caused by the shipping carrier, may incur additional repair charges before
warranty service begins and/or may void this warranty. If any product
accessories (included and/ or optional) are shipped with the product, MAGMATIC
and/or the MAGMATIC Authorized Service Center shall have no liability
whatsoever for the loss and/or damage to any such accessories, nor the safe
return thereof. If the requested warranty repairs or service (including parts
replacement) are within the terms of this warranty, MAGMATIC will pay return
ground transportation shipping charges to a single designated point within the
United States.
SAFETY GUIDELINES
This fixture is a sophisticated piece of electronic equipment. To guarantee
smooth operation, it is important to follow all instructions and guidelines in
this manual. Magmatic Effects is not responsible for injury and/or damages
resulting from the misuse of this fixture due to the disregard of the
information printed in this manual. Only qualified and/or certified personnel
should perform installation of this fixture and only the original rigging
parts included with this fixture should be used for installation. Any
modifications to the fixture and/or the included mounting hardware will void
the original manufacturer’s warranty and increase the risk of damage and/or
personal injury.
PROTECTION CLASS 1 – FIXTURE MUST BE PROPERLY GROUNDED.
THERE ARE NO USER-SERVICEABLE PARTS INSIDE THIS UNIT. DO NOT ATTEMPT ANY
REPAIRS YOURSELF. DOING SO WILL VOID YOUR MANUFACTURER’S WARRANTY. DAMAGES
RESULTING FROM MODIFICATIONS TO THIS DEVICE AND/OR THE DISREGARD OF SAFETY
INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID THE MANUFACTURER’S WARRANTY
ANDARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/OR REPAIRS.
DO NOT PLUG THIS UNIT INTO A DIMMER PACK DO NOT REMOVE THE COVER UNDER ANY
CONDITIONS KEEP THE UNIT IN AN UPRIGHT POSITION NEVER OPERATE THIS UNIT WITH
THE COVER REMOVED UNPLUG FROM POWER DURING LONG PERIODS OF NON-USE ENSURE THE
TANK IS EMPTY BEFORE STORAGE OR TRANSPORT DO NOT MOVE WHEN FILLED WITH FLUID
DISCONNECT POWER BEFORE ADDING FLUID OR PERFORMING MAINTENANCE FOR USE IN
INDOOR / DRY LOCATIONS ONLY DO NOT EXPOSE DEVICE TO RAIN AND/OR MOISTURE PLACE
UNIT IN A WELL VENTILATED AREA ALLOW 40” (100CM) ABOVE AND AROUND THE UNIT FOR
PROPER VENTILATION.
SAFETY GUIDELINES
– CAUTION: Fog machines may set off smoke alarms!
– Do not attempt installation and/or operation of this device without proper
knowledge of how to do so.
– Do not point or direct fog output in an unsafe direction.
– Do not touch the front nozzle while the machine is in operation, or
immediately after the device has been shut down, as the nozzle may get hot
during operation.
– Do not shake the device, and avoid brute force when installing and/or
operating.
– Be sure to save the packing carton in the unlikely event the device may have
to be returned for service.
– Do not spill water or other liquids into or onto the device. Be sure that
all the fog fluid is kept inside the fluid reservoir.
– Be sure that the local power outlet matches the required voltage for the
device.
– Do not remove components or disassemble the device. There are no user-
serviceable parts inside.
– Never connect this device to a dimmer pack.
– Do not attempt to operate this device if it has been damaged in any way.
– Never use this device with the cover removed.
– To reduce the risk of electrical shock or fire, do not expose this device to
rain or moisture.
– Do not attempt to operate this device if the power cord has been frayed,
crimped, and/or damaged. Replace any damaged power cords with new cords of the
same power rating.
– Do not remove or break off the ground prong from the electrical cord. This
prong is used to reduce the risk of electrical shock and fire in case of an
internal short.
– Always disconnect from main power before making any connection, performing
cleaning or maintenance, or adding or draining fluid.
– Always drain the fluid before moving the device.
– Always be sure to mount this device in an area that will allow proper
ventilation.
– Always disconnect power cords during long periods of non-use.
– This unit is intended for indoor use only. The use of this product outdoors
voids all warranties.
– Always mount this unit in a safe and stable matter.
– Please route your power cord out of the way of foot traffic. Power cords
should be routed so they are not likely to be walked on, or pinched by items
placed upon or against them.
– The device should be serviced by qualified service personnel when:
- The power cords or plugs have become damaged.
- Objects have fallen on and/or liquid has spilled into the device.
- The device has been exposed to rain and/or moisture.
- The device does not operate normally or exhibits a marked change in performance.
OVERVIEW
1. Power In
2. Breaker
3. DMX In
4. DMX Out
5. Wired Remote Port
6. Touch Display Screen
7. Safety Cable Attachment| 8. Carry Handles (x2)
9. LED Array
10. Fog Outlet
11. Mounting Clamp Points (x4)
12. Tank Level Gauge
13. Latch Screw
14. Tank Access Panel
---|---
OPERATION
- When first unboxing, open the shipping carton and carefully remove the device. Be sure to remove ALL the packing material, paying particular attention to the area around the fog outlet vent.
- Always set up the device on a flat dry surface.
- Make sure that the unit is disconnected from power before adding any fluid to the tank.
- To access the fluid tank, unscrew the latch screw that is located on the backside of the unit, near the printed notice about the tank fluid, then open the access panel.
- To fill the tank, remove the tank from behind the tank access panel. Unscrew the tank cap and fill with MAGMATIC ATMOSITY fluid (SKU# AFF only), then replace the cap.
- Never run the device on anything other than an approved, MAGMATIC branded fluid, as doing so can result in severe damage to your device.
- When placing the tank back behind the access panel, be careful not to pinch, twist, or tangle the feed tube connected to the tank cap.
- To close and secure the tank access panel, tighten the latch screw by pushing it down while rotating.
- After reconnecting the device to a power source and switching it on, allow the fluid to warm up for at least nine (9) minutes before beginning fog emission.
PLEASE NOTE:
While the fog duration setting can be set as high as 250 seconds, the
individual bursts of continuous fog output will only occur for a maximum of 8
seconds. For example, when the user sets a duration of 250 seconds, this does
NOT mean that the device will be emitting fog continuously for the entire
250-second period. Rather, the device will produce a series of shorter fog
bursts, each lasting up to 8 seconds, throughout the 250-second period.
CONTROL PANEL
This fixture includes a system menu with an easy-to-navigate touch screen
control panel where all necessary settings and adjustments are made. When
first powering on the fixture, the fixture’s main menu will be displayed (see
Main Menu Screen below).
Press the main menu icon you would like to access. Use the ENTER button to
access the sub-menus and use the UP and DOWN buttons to make adjustments.
Press the ENTER button to confirm your adjustments. You may exit the main menu
at any time without making any adjustments by pressing the BACK/EXIT button.
SYSTEM MENU
| DMX SET| DMX ADDRESS| 1 – 512| |
---|---|---|---|---|---
DMX MODE| 1-CH| |
4-CH| |
7-CH| |
| PERSONAUTY| Wifi Set| Wifi Name| |
Wifi Passcode| |
Wifi IP| |
Willi Port| |
Reset Network| Complete|
Failed, try again|
Wifi > DMX &Magfly| On / Off| Mows APP data to be converted to DMX data
and then sent out via DMX port and Ma”
LCD Set| Screen OFF| Never|
10s|
The 40s|
1 min|
2 min|
5 min|
10 min|
20 min|
Display Flip| 0 deg / 180 deg|
Magfly Set| Magfly Channel| 0 – 14| When Magill? is not equipped. selecting
this function causes ‘Optional Module Not Installed– to show on the screen.
| PERSONALTY (cont’d from prey page)| MagRF Learn| Frequency Matching
feature.
The display will read Connected” if the connection attempt succeeds within 20
seconds. Otherwise, the display will read “Connection Failed.”| When Map)/ is
not equipped. selecting this function causes “Optional Module Not Installed”
to show on the
---|---|---|---|---
Last State| Yes / No| When powered up, the device adheres to last settings
used before power was shut off
Default| Yes / No| Restore to factory settings
| MANUAL| | Off|
Auto 1-4
Color 1-50
Intensity
0% – 100%
| TIMER| Interval| 0 – 2500 s| Start or pause device operation according to
these values by pressuring the Play/Start icon.
Duration| 0 – 250 s
| LED Off
Auto 1-4
Color 1-50
Intensity 0% – 100%
| PRESET| OPT Effect| OPT1| Adjusts fog hang time.
2
OPTOPT3
OPT4
| PRESET (cont’d from prey page)| LED Status| On| LED on
---|---|---|---|---
Follow| LED illuminates in sync with fog output
Off| LED off
LED Bright| 0% – 100%|
LED Effect| Off| Special effects
Random
Pulse
Strobe
LED Style ol| LED Off| Manual fogging effects
Auto 1-4
Color 1-50
RF1 Style| LED Off| Wireless Remote Button 1
Auto 1-4
Color 1-50
RF2 Style| LED Off| Wireless Remote Button 2
Auto 1-4
Color 1-50
RF3 Style| LED Off| Wireless Remote Button 3
Auto 1-4
Color 1-50
RF4 Style| LED Off| Wireless Remote Button 4
Auto 1-4
Color 1-50
| INFORMATION| State| Normal / Error|
Slot 1| Null|
Magaly|
Wifi|
MagRF|
Slot 2| Null|
Magaly|
Wit|
MagRF|
| INFORMATION (cont’d from prey page)| Last Control| LCD_auto| Displays
current source of device control
---|---|---|---|---
LCD_manual
DMX
Wifi
MagRF
MagRemote
Error
MagRemote State| Yes / No| Displays whether remote control is connected
Wifi Connect| Null| No available Wifi source
Phone| Mobile phone Wifi source
Route| Router Wifi source
No| Wifi module not installed
Wifi IP| Display shows “No” if Wifi module is not installed
Magaly CH| 0 – 14|
DMX Addr| 1 – 512|
DMX Mode| 1 / 4 / 7|
Timer Int| Os – 2500s|
Timer Dur| Os – 250s|
Heating| 0% – 100%|
Heater State| Normal|
Error|
No Heat|
LCD Ver| V1.2|
Sftwr Ver| V1.0|
DMX CHANNEL FUNCTIONS & VALUES
CHANNEL | VALUES | FUNCTION | |
---|---|---|---|
1-CH | 4-CH | 7-CH | |
1 | 1 | 1 | |
000 – 009 | Off | ||
010 -127 | LED On (1-second delay after start of fog burst) | ||
128 – 255 | Max Foq Output, LED On | ||
2 | Macro | ||
000 – 004 | LED Off | ||
005 – 154 | Macro 1 – Macro 50 (see Macro Table) | ||
155 -180 | Fog burst & lighting display loop (2s cycle) | ||
181 – 205 | Fog burst & lighting display loop (1s cycle) | ||
206 – 230 | Auto Mode 2 | ||
231 – 255 | Auto Mode 1 | ||
2 | 000 – 255 | Red, 0% -100% | |
3 | 000 – 255 | Green, 0% – 100% | |
4 | 000 – 255 | Blue, 0% – 100% | |
5 | 000 – 255 | Amber, 0% -100% | |
3 | 6 | Flash | |
000 – 031 | Off | ||
032 – 095 | Random Strobe, slow to fast | ||
096 – 159 | Pulse, effect in sequence | ||
160 – 255 | Strobe effect, slow to fast | ||
4 | 7 | Dimmer | |
000 – 003 | Off | ||
004 – 255 | Dimmer, 1% to 100% |
MACRO TABLE
MACRO NO. | DMX VALUES | MACRO NO. | DMX VALUES |
---|---|---|---|
1 | 005 – 007 | 26 | 080 – 082 |
2 | 008 – 010 | 27 | 083 – 085 |
3 | 011 – 013 | 28 | 086 – 088 |
4 | 014 – 016 | 29 | 089 – 091 |
5 | 017 – 019 | 30 | 092 – 094 |
6 | 020 – 022 | 31 | 095 – 097 |
7 | 023 – 025 | 32 | 098 – 100 |
8 | 026 – 028 | 33 | 101 – 103 |
9 | 029 – 031 | 34 | 104 – 106 |
10 | 032 – 034 | 35 | 107 – 109 |
11 | 035 – 037 | 36 | 110 – 112 |
12 | 038 – 040 | 37 | 113 – 115 |
13 | 041 – 043 | 38 | 116 – 118 |
14 | 044 – 046 | 39 | 119 – 121 |
15 | 047 – 049 | 40 | 122 – 124 |
16 | 050 – 052 | 41 | 125 – 127 |
17 | 053 – 055 | 42 | 128 – 130 |
18 | 056 – 058 | 43 | 131 – 133 |
19 | 059 – 061 | 44 | 134 – 136 |
20 | 062 – 064 | 45 | 137 – 139 |
21 | 065 – 067 | 46 | 140 – 142 |
22 | 068 – 070 | 47 | 143 – 145 |
23 | 071 – 073 | 48 | 146 – 148 |
24 | 074 – 076 | 49 | 149 – 151 |
25 | 077 – 079 | 50 | 152 – 154 |
DIMENSIONAL DRAWINGS
Dimensions may not be drawn to scale.
TROUBLESHOOTING
If you experience low output, pump noise, or no output at all, disconnect the device and discontinue use immediately. Do not attempt to continue operation as this may damage the machine. Check the fluid level, the breaker, and the wall outlet to make sure that it is sending power. If all the above factors do not appear to be causing the issue, and the unit still fails to operate correctly, the unit will require service. Please contact Magmatic Effects for assistance.
CLEANING & MAINTENANCE
When storing your device, be sure to store in a cool area. Cover the device so that dust does not build up on the device. When storing for long periods of time it is highly advisable to run the device at least once every 3-4 months. Long periods of inactivity can severely shorten the life of your device. Only run Magmatic’s Atmosity fluid (SKU# AFF) through your machine. Never run plain water, vinegar, or any other liquid solution through your device, as doing so will severely damage your device.
SPECIFICATIONS
PERFORMANCE
Rated Power: 1450W
Max Output: 50,000 CFM* (cu ft/min.)
Max Continuous Output: 8 Seconds @ Full
Max Throw Distance: 25 Feet
Initial Ready Time: 9 Minutes
Cycling Ready Time: 1 Minute
Fluid Capacity: 2.5L
Fluid Consumption: 180ml/min.
COMPATIBLE FLUID
Atmos Flash Fog Fluid (AFF-4L)
Atmos Extreme Filtered Fog Fluid (AEF-4L)
CONSTRUCTION
Thermally Protected Heat Exchanger
Advanced HPA (high-pressure air) Pump Technology Energy Saving Mode with Auto-
Clean Process Sealed Fluid
Reservoir
External Visual Fluid Level Detection
Compact Light Weight Mobile Design
CONTROL
3 DMX Channel Modes (1 / 4 / 7)
Onboard LCD Touch Control Panel
DMX-512 and RDM Protocol Support
Optional MagFLY Wireless DMX Transceiver
Optional MagRF and Wired Remotes
CONNECTIONS
5-pin locking XLR, In/Out Data Connectors
IP65 Locking Input Power Connector
With Wired Digital Communication Network
SIZE / WEIGHT
Length: 16.26 in. (413mm)
Width: 7.60 in. (193mm)
Height: 14.80 in. (376mm)
Weight: 29.5 lbs. (13.4kg)
ELECTRICAL
Input Voltage: 120V, 230V, 240V 50/60Hz
9A (NFB) Resettable Breaker
Max Power Consumption: 1560W
THERMAL
Maximum Ambient Temperature (Ta max) 104°F (40°C)
Exterior Surface Temperature, Steady State: 140°F (60°C)
APPROVALS / RATINGS
CE | cETLus (pending) | IP20
Specifications are subject to change without notice.
Documents / Resources
|
MAGMATIC RSS160 Sidewinder High Velocity CO2 Simulator Fog Machine with LED
Lights
[pdf] User Manual
RSS160, Sidewinder High Velocity CO2 Simulator Fog Machine with LED Lights,
Sidewinder, LED Lights Fog Machine
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>