iOttie Easy One Touch Wireless 2 User Guide
- June 10, 2024
- iOttie
Table of Contents
Easy One Touch Wireless 2
CD Slot + Air Vent Mount
Manual
Getting Started
For optimal mounting and charging, please follow the detailed instructions within this manual when using the Easy One Touch Wireless 2 Charging Mount. iOttie is not liable for possible damages due to product misuse.
Critical Information
Compatibility
The Easy One Touch Wireless 2 is compatible with all Qi-enabled smartphones
including Google, Apple, & Samsung devices.
(Wireless charging speed is dependent on phone make and model.)
Qi Wireless Charging in Vehicle
Use the included iOttie car charger and micro USB cable. If you use a third
party car charger, make sure that it is Qualcomm Quick Charge 2.0 or above.
The Easy One Touch Wireless 2’s signal may interfere with your vehicle’s TPMS
(tire pressure monitoring system). If you notice that your TPMS light turns
on, reposition the mount to prevent the signals from interacting.
At a Glance
Qi Alignment Guide
The Qi receiver coil is usually located in the center area of the phone.
Check with your phone’s manufacturer for Qi coil location. Below are some
examples for commonly used phones.
For optimal wireless charging, please make sure your smartphone and mount’s Qi coils are aligned.
Adjusting the Mount
Cradle knob
When switching between landscape and portrait mode, loosen the cradle knob to
rotate the cradle. Tighten the knob to lock the mount in your desired
position.
Foot release button
The foot can be adjusted to 3 different height settings to accommodate
different phone sizes. Once setup is chosen, the foot is designed to align
with the center of the side arms for optimal Qi wireless charging.
Connecting to Power
The
Easy One Touch Wireless 2 is powered by a micro USB cable.
There is no on/off switch on the mount. Once it is plugged in, the mount will
remain on until the vehicle is turned off.
Installation
CD Slot Mount
- Attach the CD mount to the cradle. Tighten using the adjustment knob.
- Put the mount into the CD slot and pull the lever to lock it into place.
- Test to make sure the mount is secure. Insert bracket only if needed.
- If using the bracket, make sure the arrow is pointing inward. 4. Align your smartphone in the center of the Easy One Touch trigger button. The indicator light will turn on when the phone is successfully charging.
To avoid possible damage to the product and your vehicle, remember to remove all CDs from the CD slot before using your Easy One Touch Wireless 2. iOttie is not liable for damage due to misuse.
Air Vent Mount
-
Attach the air vent mount to the cradle. Tighten using the adjustment knob.
-
Loosen the twist lock and push the mount completely onto the air vent blade.
-
Slowly tighten the twist lock to ensure a secure connection to the air vent blade.
-
Align the smartphone in the center of the Easy One Touch trigger button. The indicator light will turn on when the phone is successfully charging.
**** Please use caution when adjusting the twist lock on the air vent blade.
Using the Easy One Touch Mechanism
The Easy One Touch lock and release mechanism makes it simple to mount & retrieve smartphones in seconds.
Mounting
-
Squeeze the release bars on either side of the mount to open the locking side arms.
-
Press your device against the Easy One Touch trigger button. The mount’s arms will automatically close on contact for a secure hold.
Releasing
Press the release bars.
The arms will open so you can retrieve your device.
Wireless Charger Specifications
INPUT| DC 5V/3A
DC 9V/2A
DC 12V/1.5A
---|---
OUTPUT| 10W (ANDROID), 7.5W (APPLE)
CHARGING PORT| MICRO USB
LENGTH| 4.3″
WIDTH| 2.4″
HEIGHT| 4.5″
WEIGHT| 3.6 oz
Car Charger Specifications
| INPUT | 12V~24V |
|---|---|
| OUTPUT | DC 5V/3A |
9V/2A
12V/1.5A
Charging Indicator
| SOLID GREEN LIGHT | Smartphone is charging. |
|---|---|
| BLINKING RED LIGHT | Smartphone is not charging. |
Foreign object detected, or the smartphone or mount is overheating.
Declaration of Conformity (FCC)
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. You can
refer to the following completed FCC warnings.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference
that may cause undesired operation.
Note
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Operational Warnings
During the charging process, the transfer of electricity gives off heat. Your
device may become warm, but should not become exceedingly hot.
If the device gets wet, please cease charging immediately. Remove all plugs
and dry the product completely. Device is only to be operated in a dry, indoor
environment.
Please be careful of excessive drops, dents, punctures, or deformities on the
device. If you are concerned. please unplug the device and contact the
manufacturer.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Operating this device in a hot environment or in direct sunlight for a long
period of time may cause malfunctions. We recommend keeping the product in
cooler temperatures.
Please use included components for an optimal experience. To support of
wireless charge when using a third party car charger or a USB Power Adapter
use a minimum output of both “9.0V-1.67A or 5.0V-2.0A” and at least CC 2.0.
The product’s signal could possibly interfere with you TPMS (tire pressure
monitoring system). If you notice that your TPMS light turns on, please try
using your mount in different locations to avoid the signals from interfering
with each other.
California Proposition 65 this product contains chemicals known to the state
of California to cause cancer and birth defects or other reproductive harm.
CAUTION OLD ELECTRICAL APPLIANCES MUST NOT BE DISPOSED OF TOGETHER WITH
THE RESIDUAL WASTE, BUT HAVE TO BE DISPOSED OF SEPARATELY.
IC Warning
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
The device has been evaluated to meet general RF exposure requirement.
To maintain compliance with RSS-102 – Radio Frequency (RF) Exposure
guidelines, this equipment should be installed and operated with a minimum
distance of 20cm between the radiator and your body.
EU Declaration
Hereby, iOttie declares that the radio equipment type HLCRIO143 is in
compliance with Directive 2014/53/EU.
The full text of the EU Declaration of Conformity is available at the
following web address: https://www.iottie.com/wp-
content/uploads/2023/05/dochlcrio142_143_144.pdf
https://www.iottie.com/support/customerservice If you love your iOttie product, let us know by leaving a review online, or connect with us on our social platforms.
| www.iottie.com
---|---
| cs@iottie.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>