iottie Auto Sense 2 Fold Dashboard Mount User Guide

June 10, 2024
iOttie

Sense 2 Fold Dashboard Mount
User Guide

Product Assembly & Installation

Connect the mount cradle to the ball joint. Tighten the cradle knob.
Choose a flat mounting location on your dashboard and wipe the surface clean. Peel or the film on the dashboard pad and evenly press onto the desired location. Wait 20 minutes.

Remove the plastic cover from the suction cup and firmly press onto the dashboard pad. Push the lever down to engage suction.
Do not install on leather dashboards.

Connecting to Power

Plug the included USB-C cable into the USB port located on the back of the mount cradle.

Connect the USB-C cable to your vehicle’s USB-C port or auxiliary power outlet via a 20W adapter.

Mounting Your Phone

Hold the phone in front of the mount cradle to activate the automatic clamping arms.

Place the phone inside the mount. The arms will close automatically after one second and wireless charging will begin.

Alignment Guide


Portrait / Phone open (foot down)| Landscape / Phone open

Portrait / Phone closed (mount rotated)| Landscape / Phone closed

Landscape / Phone closed
Don’t forget to leave a review.
Follow @iottie for the latest news and updates!
Need help? Reach out to us directly by emailing: cs@iottie.com
Please visit our website for more information. www.iottie.com
Full Manual & Product Registration
http://www.iottie.com/qr-code?sku=ATSWCG208
Scan QR code for  full manual & Product Registration

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the product.
NOTE: This equipment has been tested and found to comply with the limits for a wireless power transfer, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Hereby, iOttie, Inc declares that the radio equipment type ATSWCG208 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.iottie.com.
Declaration for EU Compliance: Operation Freq: 118.59-151.12 kHz, Max. RF power transmitted: H-Field 20.35dBoffA/m @3m distance.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

-Warning Statement:
RSS-GEN ISSUE 5, 8.4 User manual notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licenceexempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that are deemed to comply without testing of specifc absorption ratio (SAR).
This equipment should be installed and operated with minimum distance 10cmbetween the radiator & your body.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals