iottie Auto Sense 2 Dashboard and Windshield Mount User Guide

: June 10, 2024
: iOttie

Table of Contents

iottie Auto Sense 2 Dashboard and Windshield Mount
Product Information
Product Usage Instructions
Product Assembly & Installation
Connecting to Power
Mounting Your Phone
FCC STATEMENT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

iottie Auto Sense 2 Dashboard and Windshield Mount

Product Information

The Auto Sense 2 Dashboard & Windshield Mount is a phone mount that can be attached to your car’s dashboard or windshield. It features wireless charging and is compatible with iPhone and Samsung Galaxy phones. The mount comes with a USB-C cable for charging and requires a 20W adapter (not included) to be connected to your car’s auxiliary power outlet.

It is important to note that the dashboard pad included should not be installed on leather dashboards.

The mount also contains a license-exempt transmitter/receiver that complies with Innovation, Science and Economic Development Canada’s license-exempt RSS(s).

Product Usage Instructions

Choose a flat mounting location on your dashboard or windshield and wipe the surface clean.
Peel off the film on the dashboard pad and evenly press onto the desired location. Wait for 20 minutes before proceeding to the next step.
Connect the USB-C cable to your car’s auxiliary power outlet via a 20W adapter (not included) or to your car’s USB-C port.
Place your phone inside the mount. The arms will close automatically after one second and wireless charging will begin.

If you encounter any issues or need help with the product, you can reach out to the manufacturer directly by emailing cs@iottie.com or by visiting their website for more information at www.iottie.com.

Product Assembly & Installation

iottie-Auto-Sense-2-Dashboard-and-Windshield-Mount-
fig-1

Connect the mount cradle to the ball joint. Tighten the cradle knob.
Choose a flat mounting location on your dashboard and wipe the surface clean. Peel off the film on the dashboard pad and evenly press it onto the desired location. Wait 20 minutes.
Remove the plastic cover from the suction cup and firmly press it onto the dashboard pad. Push the lever down to engage suction.

Do not install on leather dashboards.

Connecting to Power

Plug the included USB-C cable into the USB port located on the back of the mount cradle.
Connect the USB-C cable to your vehicle’s auxiliary power outlet via a 20W adapter (not included).
Connect the USB-C cable to your vehicle’s USB-C port.

iottie-Auto-Sense-2-Dashboard-and-Windshield-Mount-
fig-5

Mounting Your Phone

Hold the phone in front of the mount cradle to activate the automatic clamping arms.
Place the phone inside the mount. The arms will close automatically after one second and wireless charging will begin.

Alignment Guide

iottie-Auto-Sense-2-Dashboard-and-Windshield-Mount-
fig-8

FCC STATEMENT

Declaration of Conformity (FCC)

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. You can refer to the following completed FCC warnings.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.

Note
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 15cm between the radiator & your body.

Warning Statement

RSS-GEN ISSUE 5, 8.4 User manual notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s license-exempt RSS(s).
Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B). This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that are deemed to comply without testing of specific absorption ratio (SAR). This equipment should be installed and operated with a minimum distance of 10cm between the radiator & your body.

We’d love to hear from you!