living co CL-RSCX671 Rotary Head Shaver Instruction Manual
- June 4, 2024
- LIVING CO
Table of Contents
living co CL-RSCX671 Rotary Head Shaver
SAFETY INSTRUCTIONS
WARNING:
Separate the handheld part from the charging cord before cleaning/rinsing the
handheld part in water.
- This product uses a USB charging cable. You can use any standard 5V USB outlet from a charge adapter or a USB outlet source from cars, computers, and other devices for charging.
- If the charging cable is damaged, replace it with a new one to avoid overheating.
- The product shall be charged and stored between 5 and 35℃.
- Make sure the charge and charging cable are dry. Do not plug or unplug with wet hands to prevent electric shock.
- Always inspect the shave head for damage or deformation before use, in order to avoid damage to your skin.
- Clean the shaver with clean water, but do not leave it to soak in water.
- Do not use salt water, hot water above 60 °C, thinners, gasoline, alcohol or other chemicals to clean the electric shaver.
- It is necessary to cover the electric shaver head with the protective cover when you travel to protect foil blades.
- During use and the charging process, the electric shaver may be slightly heated. This is normal and does not indicate fault.
- Please do not charge the electric shaver too long or leave connected to the supply once charged. Charging connection should be for 90 minutes.
- Do not store the electric shaver in direct sun light or near other sources of heat.
- No liability can be accepted for any damage caused by non-compliance with these instructions or any other improper use or mishandling.
- For hygiene reasons, do not share this appliance with other people, the product is intended for personal use only.
- Suitable for cleaning under a water. tap.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
Product Overview
- Five head shaver
- ON/OFF button
- Nose & ear hair trimmer
- Hair trimmer
- Lubricating oil
- USB charging cable
- Charging socket
- LED display
- Guide comb for hair trimmer (3,5,7mm)
- Cleaning brush
How to Use
Charge
- When the display shows “Available time, 05 minutes”, the indicator light will flash, indicating that the battery is low-energy and needs charging (Fig.1).
- Plug the USB charging cable end into the electric shaver, then connect the USB cable to the charger and plug it into the power socket (Fig. 2), or plug the other end of the USB cable into a USB port of a computer or other source.
- When the power is turned on, the display will light up, with scrolling numbers that will increase as the charging time extends, indicating that it’s charging (Fig. 3).
- Full charging takes about 1.5 hours on a continuous basis. After full charging, “FULL” and “90 min” will be displayed, indicating the shaver has been fully charged and can be used for about 90 minutes
The LED display of this product can display the remaining energy. A fully charged electric shaver can provide a shaving duration up to about 90 minutes, but the actual shaving duration may be less than expected due to differences in shaving habits, cleaning habits and beard types.
The electric shaver can be used while it’s being charged by means of a USB cable connection if it still has remaining energy.
Shave Beard and Head
- Press the switch button to turn on the electric shaver (Fig. 5).
- Move the electric shaver foil head against the growth direction of your beard on your skin and make straight and reciprocated movements (Fig. 6).
- Hair on your neck can also be shaved (Fig.7).
- Before shaving your head, clean it with warm water and keep your hair dry. For a better effect of use, please use the brush if you need to clean the shaving head during the head shaving process, and wash the shaving head after shaving is completed (Fig.7-1).
When shaving completed
Press the switch button again to turn off the electric shaver, and then cover
it with the protective cover to avoid damages to the shaving foil head.
Please do not use any damaged shaving head to avoid injury to your skin;
instead, replace it immediately with our original spare shaving head which can
be bought where you buy your shaver.
Travel Lock
- Press and hold the on/off switch button for 3 seconds, and then the electric shaver LED display indicates that the safety lock has been activated (Fig.8).
- Repeat the above step to unlock (Fig.9).
Intelligent Display of Contents
- When the electric shaver is overloaded, it will be automatically turned off, and the LED display will indicate stall protection. At this time, it should be cleaned before use (Fig.10)
- When the faucet (tap) symbol flashes on the LED display, it indicates that the electric shaver needs to be cleaned (Fig. 11).
Maintenance
Wash and Clean with Water
- Before cleaning, be sure to separate the electric shaver from the USB charging cable and press the switch to the off state.
- Pinch both sides of each shaving head to lift up and open all shaving heads (Fig. 12).
- The electric shaver can be washed directly under running tap (Fig. 13), but please do not soak it in water for a long time.
- After washing, drain any excess water, put it horizontally and air-dry it. Do not wipe the shaving head part with tissue or cloth, which may cause damage.
- First air-dry the electric shaver, then cover it with the protective cover to prevent damage to the foil and avoid the accumulation of dust.
Separate the handheld part from the power cord before cleaning the handheld part in water.
Operating Instructions for Hair Clipper
Switch off the shaver, pull it up (no screw) to separate the shaving head (this will click on / off), and insert the flange of the hair clipper head part into the groove on the top of the shaver body.
Then press down the hair clipper head part to mount it on the shaver body (a click will be heard) (Fig.17).
Trim
Note: Make sure your hair is clean and dry, and please don’t use the
product for wet hair just washed.
- Before trimming, first do remember to comb hair along its growth direction with a comb.
- Mount the comb accessory into the slots on both sides of the product (a click will be heard), and make sure it’s mounted correctly (Fig.18).
- The included combs are optional for different haircut lengths, such as 3mm,5mm and 7mm, which can be mounted as required. To replace a comb, unload it from the groove on one side first (Fig.19).
- Press the ON/OFF button and move the product slowly on hair. To get the best haircut effect, it’s necessary to move the product against the growth direction of hair.
Clean
- Pull out the hair clipper head and clean the trimming part with the included brush or wash the hair clipper head assembly with water.
- Don’t clean the product with such liquids as abrasives, alcohol, petrol or acetone.
- Clean the product immediately each time it’s used.
Operating Instructions for Nose & Ear Hair Trimmer
Switch off the shaver, unclip the shave head (pull it up) to disconnect the shaving head, and insert the flange of the trimmer head part into the groove on the top of the shaver body. Then press down the trimmer head part to mount it on the shaver body (a click will be heard)(Fig. 20).
Trim Nose Hair
- Make sure your nasal cavity is clean
- Start the ON/OFF button, insert the nose & ear hair trimmer tip into one of your nasal cavities slowly and meanwhile turn the tip to remove over-long nose hair (Fig.21). The insertion depth of the tip into your nasal cavity must not exceed 0.5cm. Make sure that one side of the tip is firmly pressed against your skin.
Trim Ear Hair
- Clean your external auditory canal to ensure there is no wax.
- Start the ON/OFF button and then make the tip circle along your ear gently to remove protrudent hair on your helix (Fig.22).
- Insert the nose & ear hair trimmer tip into the external auditory canal carefully. The insertion depth of the tip into your auditory canal shall not exceed 0.5m, or else your eardrum may be injured.
Specification
- 800mAh lithium-ion battery
- Waterproof function: IPX6
- Charge time: 1.5 hours
- Operation time: 90 mins
- 5V USB Charge
Responsible Disposal
At the end of its working life, do not throw this product out with your household rubbish. Electrical and electronic products contain substances that can have a detrimental effect on the environment and human health if disposed of inappropriately. Observe any local council regulations regarding the disposal of electrical consumer goods and dispose of it appropriately for recycling. Contact your local authorities for advice on recycling facilities in your area. Please keep the original packaging carton and materials in a safe place. It will help to prevent any damage if the product needs to be transported in the future. In the event it is to be disposed of, please recycle all packaging material where possible.
Warranty
We pride ourselves on producing a range of quality home appliances that are both packed with features, and completely reliable. We are so confident in our products, we back them up with a 2 year warranty when accompanied by proof of purchase.
Now you too can relax knowing that you are covered.
- Customer Helpline NZ: 0800 422 274
- IM Version 1.0 – Jan. 2022