living co CM5018D-GS Coffee Machines Instruction Manual

: June 3, 2024
: LIVING CO

living co CM5018D-GS Coffee Machines Instruction Manual

IMPORTANT SAFETY INSTRUCTIONS

Before using the electrical appliance, the following basic precautions should always be followed including the following:

Read all instructions before use. Retain this guide for future reference.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
When the appliance is not in use and before cleaning, unplug the appliance from the outlet firstly.
To protect against fire, electric shock and injury to persons do not immerse main parts of the product, cord, plug, in water or other liquid.
The appliance must not be immersed in liquid.
Remove plug from wall outlet before cleaning and when not in use. Allow appliance to cool down completely before removing/attaching components, or before cleaning.
The use of accessory attachments not included with the appliance may result in fire, electric shock or injury to persons.
Place the appliance on a flat surface or table. Do not allow power cords to hang over the edge of table or counter.
Ensure that the power cord does not touch any hot surface of the appliance.
Do not place the coffee maker on any hot surface or near heat sources in order to avoid damage to the appliance.
To disconnect, remove the plug from the wall outlet. Always hold the plug and never pull the cord.
Do not use the appliance for any purpose other than intended use. Place the unit in a dry environment.
Do not touch the hot surface of the appliance (such as the steam wand and the steel mesh). Always use the handle or dials. Be careful not to get burned by the steam emitted from the appliance.
Never operate the coffee maker without water.
DO NOT remove the metal funnel while brewing coffee. Only remove the metal funnel to make additional coffee more than 10 seconds after brewing has finished. Caution should also be taken while removing the metal funnel since the metal parts will be hot. Make sure to hold it by the handle and to use the filter retention clip to dispose of coffee grounds. Caution should be taken when moving the unit with hot liquids inside.
Connect the plug to a wall outlet before use, and turn any switches off before the plug is removed from wall outlet.
This appliance is intended to be used in household and similar applications such as:
- staff kitchen areas in shops, offices and other working environments.
- farm houses.
- by clients in hotels, motels and other residential type environments.
- bed and breakfast type environments.
Do not use the appliance outdoors.
WARNING: The filling aperture must not be opened during use.
Warning: Potential injury from misuse. The heating element surface is subject to residual heat after use.
Cleaning and user maintenance shall not be made by children without supervision.
Save these instructions for future reference.

PRODUCT OVERVIEW

COFFEE MAKER AND ACCESSORIES

Product Overview

CONTROL PANEL

Control Panel

INSERTING THE FILTER INTO THE PORTAFILTER

To insert the selected filter (two cup or one cup) in the portafilter, make sure to align the notch on the filter with the groove inside the portafilter.
Turn the filter to the left or right to lock in place. This will help secure the filter in the portafilter.

HOW TO USE

BEFORE THE FIRST USE

Before first use you should rinse the coffee maker with warm water as following:

Pull out the water tank of the coffee maker. Pour clean water into the tank, ensuring that the water level should does not exceed the “MAX” mark and is no less than the “MIN” mark on the side of the tank. When re-inserting the tank, angle forward slightly to allow the extraction tube to fit into the tank, try to avoid direct pressure / stress onto the extraction tube from the sides of the tank.
Insert the single or double cup filter into the Portafilter (see previous section), then position the portafilter under the holder (see Fig.1) and turn it anticlockwise until it is fixed tightly (see Fig.2 and Fig.3).
Place an espresso cup on the drip plate. Make sure the steam dial is in the “ ” position.
Connect the supply plug to a wall socket and press the ON/OFF button “ ” to turn the appliance on. The power indicator (red) will be illuminated.
Press down the pump on/off control button “ ”, the pump will activate and water will begin to flow from the portafilter. Once water flows, push the pump on/off control button again to switch off. The purpose of this step is to pump the water from the tank into the housing heating chamber. the coffee temperature indicator light (green) will activate.
Make sure the coffee/steam on/off button “ ” is in the off position (button not depressed so its higher) , the appliance will begin preheating until the coffee temperature indicator (green) illuminates, indicating that the preheating process has completed (note, this will cycle on / off during use). The temperature gauge will rise and then stabilise after around 30 seconds.
Press down the pump on/off control button“ ” again, and water will flow out.
After water has dispensed for approximately 1 minute, press the pump control button“ ”, once more. Dispose of the water collected in the espresso cup, clean the cup and you can now start brewing coffee.

Note: There may be a louder noise when pumping the water for the first time, this is normal, as the appliance is releasing the air in the appliance. After about 20 seconds, the noise will disappear.

PREHEATING

It is recommended to preheat the appliance before making coffee, including the portafilter and cup, so that the coffee flavour will not be influenced by the cold surfaces

Pull out the water tank of the coffee maker. Pour clean water into the tank, ensuring that the
water level should does not exceed the “MAX” mark and is no less than the “MIN” mark on the side of the tank. When re-inserting the tank, angle forward slightly to allow the extraction tube to fit into the tank, try to avoid direct pressure / stress onto the extraction tube from the sides of the tank.
Insert the filter into the Portafilter (see previous section), then position the portafilter under the holder (see Fig.1) and turn it anticlockwise until it is fixed tightly (see Fig.2 and Fig.3).
Make sure the steam dial is set to “0” and place an espresso cup on the drip plate.
Connect the supply plug to a wall socket and press the ON/OFF button “ ” to turn the appliance on. The power indicator (red) will be illuminated.
Make sure the coffee/steam on/off button “ ” is in the off position (button not depressed so sits higher).
Press down the pump on/off control button“ ” wait for a moment and water will begin flowing out. When water is flowing out, immediately press the pump on/off control button again to switch off. The purpose of the step is to pump the water from the tank into the housing heating
chamber.

MAKING ESPRESSO COFFEE

Connect the supply plug to a wall socket and press the ON/OFF button “ ” to turn the appliance on. The power indicator (red) will be illuminated.
Check that the water tank has sufficient water added and that the steam dial is set to “0”.
Insert the desired filter (single or double cup) into the Portafilter (see previous section), then position the portafilter.
Add ground coffee to the filter with the measuring spoon (one level spoon should suffice for one cup of coffee). Press the coffee powder down tightly with the tamper.
Position the portafilter under the holder (see Fig.1) and turn it anticlockwise until it is fixed tightly (see Fig.2 and Fig.3).
Place an espresso cup under the portafilter and positioned on top of the drip tray.
Press the ON/OFF button to turn on the unit; the power indicator will illuminate red. Make sure the coffee/steam on/off button “ ” is in the off position (button not depressed so sits higher) and that the steam pressure dial is set to “ ”).
Wait for the coffee temperature indicator light to switch on (green), then press down the pump on/off control button“ ”, wait for a moment and coffee will begin flowing out. The temperature gauge will rise and then stabilise after around 30 seconds.
Press the pump on/off control button“ ”to switch off manually when the desired coffee quantity is obtained or if the colour of the coffee coming out starts to weaken.
After finishing making coffee, press the ON/OFF button, and the power indicator and coffee temperature indicator will switch off.
Remove the portafilter by turning clockwise and tip out the coffee residue.
Let the components cool down completely, then rinse under running water

WARNING: Do not leave the coffee maker unattended while in use.

NOTE: During coffee brewing or steaming, it is normal that the Coffee / Steam temperature indicator light may go on/ off – this indicates that the heater is regulating the temperature to the required level.

MAKING CAPPUCCINO

You can make a cup of cappuccino by topping a cup of espresso with frothing milk.
Note: During steaming, the portafilter must be assembled in position.

Method:

Prepare espresso first as per the instructions above, make sure that the steam dial is at the ” ” position.
Press the coffee/steam on/off button “ ”, waiting until the steam temperature indicator illuminates (green). The temperature gauge will rise higher (than that noted when making espresso). This process will take around 1 minute.
Fill a small jug with about 100ml of milk for each cappuccino to be prepared. It is recommended to use whole milk at a refrigerated temperature (not hot).
In order to achieve ideal milk foam consistency, it is recommended to keep the steam dial in the open position for approximately 15 seconds, since the initial steam contains too much water, then keep the dial at the “0” position and conduct next step.
Insert the steam wand into the milk (approx. two centimeters deep), then turn the steam dial slowly anticlockwise. Steam will come out from the steam wand. Frothed milk is produced by moving the vessel around and from up to down.
Note: To avoid burns, never directly touch the steam outlet during operation and take care to
avoid placing hand or fingers near the outlet when discharging steam.
Note: Never turn the steam dial rapidly, as the steam will accumulate rapidly in short time which may increase the potential of the risk of steam bursts.
When the required amount of frothing is reached, you can turn the steam dial to the “0” position.
Then press the coffee/ steam on/off button.
To avoid the steam outlet being blocked after frothing milk each time, put an empty jug under the steam wand, then turn on the steam dial and press the pump on/off control button. The pump will begin operating. Once the water has been flowing for 30 seconds, press the pump control on/off button to switch off.
Let the components cool down completely, then rinse under running water. Ensure the steam wand / nozzle is thoroughly cleaned after each use. Remove the steam wand cover (tube) and rinse, while cleaning the internal nozzle with a wet towel.
Press and release the ON/OFF button to power the unit off.
Pour the frothed milk into the espresso that was previously prepared. Sweeten if desired by sprinkling the froth with a little cocoa powder.

Note: Please follow the instructions below if the steam outlet is blocked: turn the steam dial to “0” position and let the coffee maker cool down for about half an hour. Poke the steam outlet several times with a needle around 1mm in diameter. Finally, press the coffee/steam button and turn on the steam dial to check if the appliance can produce steam normally when the steam indicator (green) illuminates.

Note: After steaming, allow the coffee maker to cool down at least for 5 minutes before making coffee again, otherwise a burnt odour may be noticeable in the prepared coffee. If you want to make coffee immediately: press and release the coffee/ steam button and dip the steam wand into a cup. Press the pump on/off control button down and turn on the steam control dial; water will flow out from steam wand. After the ready temperature indicator, press and release the pump control button, then turn the steam control dial to “0” position. When the ready indicator illuminates, the appliance is prepared for making coffee once again.

FROTHING MILK / PRODUCING STEAM TO HEAT LIQUIDS

The steam wand can be used to froth milk and make hot beverages like drinking chocolate, water or tea.

Method:

Remove the water tank and fill it with desired amount of water. The water level should be between the “MAX” mark and the “MIN” mark in the tank. Re-insert the tank into the appliance securely.
Connect the appliance to the wall socket.
Press the ON/OFF button “ ” to turn on the unit; the power indicator will illuminate in red.
Press down the pump on/off control button “ ”, the pump will activate and water will begin to flow from the portafilter. Once water flows, push the pump on/off control button again to switch off. The purpose of the step is to pump the water from the tank into the housing heating chamber. the coffee temperature indicator light (green) will activate.
Press down the coffee/steam on/off button “ ” , the appliance will begin preheating until the coffee temperature indicator (green) illuminates, indicating that the preheating process has completed.
Dip the steam wand into the liquid to be heated. If you want to froth milk, dip the steam wand about 2 centimeters into the milk. Slowly turn the stand dial anti-clockwise to start making steam.
When the required amount of frothing is reached, you can turn the steam dial to the “0” position.
To avoid the steam outlet being blocked after frothing milk each time, put an empty jug under the steam wand, then turn on the steam dial and press the pump on/off control button “ ”. The pump will begin operating. Once the water has been flowing for 30 seconds, press the pump control on/off button “ ”to switch off.
Let the components cool down completely, then rinse under running water. Ensure the steam wand / nozzle is thoroughly cleaned after each use. Remove the steam wand cover (tube) and rinse, while cleaning the internal nozzle with a wet towel.
Press and release the ON/OFF button to power the unit off

AUTOMATIC POWER OFF FUNCTION

The appliance will turn off automatically if no function is activated within 29 minutes.

DRIP TRAY FLOAT MECHANISM

The drip tray incorporates a red coloured plastic float mechanism that will raise above the drip plate to indicate when the drip tray is full. In order to prevent overflow and spillage of liquids, please empty when full.
Drip Tray Float Mechanism

CLEANING

CLEANING AND MAINTENANCE:

Turn off and unplug the appliance, then let the coffee maker cool down completely before cleaning.
Clean housing of coffee maker with moisture-proof sponge often and clean water tank, drip tray and removable shelf regularly then dry them.
Note: Do not clean the appliance with alcohol or solvents. Never immerse the housing in liquid for cleaning.
Detach the portafilter by turning it clockwise, remove the filter and any coffee residue inside.
Clean it with a gentle detergent and rinse it under water. Do not wash these parts in a dishwasher.
Clean all the attachments in the water and dry thoroughly.
Ensure the steam wand / nozzle are thoroughly cleaned after each use. Remove the nozzle cover and rinse, while cleaning the internal nozzle with a wet towel.

Note: To maintain optimum operating performance, clean the appliance after every use

CLEANING MINERAL DEPOSITS

To ensure your coffee maker operates efficiently, the internal piping should be cleaned every 1-2 months to guarantee optimal coffee flavor.

Fill the tank with water and descaler to the MAX level (the proportion of water and descaler is Use a “household descale” or citric acid at a ratio of 100: 3 (water to citric acid).
Follow the preheating process above (steps 2-6) to set the water temperature”.
When there is water flowing out, switch the pump on/off control again and wait for a moment f or the appliance to reheat.
When the ready indicator illuminates green, press down the pump control button to the lower position and “brew” two cups’ worth of water/descaler (about 60ml). Then close the pump and wait for 5 seconds.
Press down the coffee/steam button, waiting until the green indicator is illuminated. Make steam for 2 minutes and then turn the steam dial to the “0” position. Press the ON/OFF button to turn off the unit immediately and let the descale collect in the internal piping for at least 15 minutes.
Restart the unit and repeat steps 2-5 at least three times, then press and release the coffee/steam button. When the green indicator is illuminated, press down the pump control button to brew until no descale is left.
Perform the brewing process (using no coffee powder) with tap water filled up to the MAX level of the water tank. Repeat the steps of 2-5 for 3 times (it is not necessary to wait 15 minutes in step.

Note: Ensure you repeat step 7 at least three times to guarantee the piping is clean.

WATER TANK EXTRACTION HOSE

When removing and fitting the water tank into the recess slot, take care not to exert pressure onto the extraction hose. Angle the water tank downwards when inserting and manually place the hose into the tank. Try to limit the amount of bending and pressure applied to the hose and ensure this sits vertically when the tank has been refitted.

The water tank extraction hose fits onto a hose socket on the upper section of the tank recess housing. Should the hose be inadvertently detached from the socket, this can be easily reattached by simply aligning the two parts and applying pressure. Firmly press the hose onto the socket.

TROUBLE SHOOTING

Symptom	Cause	Corrections
The coffee maker will not power on.	The power outlet is not switched on or is
faulty.	Ensure the plug of the power cord is correctly fitted to the socket

outlet, if the appliance still does not work, try a different socket outlet and use an alternative appliance (for example a desk lamp) to check it is functional.
Water leaks from the bottom of coffee maker.| There is excessive water in the drip tray.| Please clean the drip tray.
Water leaks from the outer side of the filter.| There is some coffee powder on the filter edge.| Ensure the filter is clean before use.
Acidic (vinegar) taste noted in the coffee.| Appliance not cleaned correctly after cleaning mineral deposits.| Clean coffee maker as per “before the first use” several times.
The coffee powder is stored in a hot, wet environment for a long time. The coffee powder has expired.| Please use fresh coffee powder and store unused coffee powder in a cool, dry place. After opening a packet of coffee powder, reseal it tightly and store in a refrigerator to maintain freshness.
Plastic taste noted in the coffee.| Appliance in use for the first time. Test run with hot water strongly recommended before making any to drinks.| Upon first use, run the coffee machine with just hot water to clean and prepare the appliance. Do not drink the initial cycle of water. Ensure water has been run for at least one minute before making coffee to serve.
Burnt taste noted in coffee.| Water flowing through grinds too slowly, leading to a bitter and burnt tasting coffee.| Adjust your grinder for a coarser grind of the beans.
The steam function will not generate froth.| The steam ready indicator is not illuminated.| The unit is only ready for frothing once the indicator is activated.
The container is too big or poorly shaped for frothing.| Use a tall and narrow cup.
Skim milk used for frothing.| Use whole milk.

Warranty

We pride ourselves on producing a range of quality home appliances that are both packed with features, and completely reliable. We are so confident in our products, we back them up with a 2 year warranty when accompanied with proof of purchase. Now you too can relax knowing that you are covered. Customer Helpline NZ: 0800 422 274 IM Version 1.0 – June, 2021