iNELS RFDEL-71B-SL Wireless Light Dimmer Key Fob Instruction Manual
- June 10, 2024
- inELS
Table of Contents
iNELS RFDEL-71B-SL Wireless Light Dimmer Key Fob
Introduction
Combination of iNELS switching element for universal use. It can be used to control electrical appliances, lights, sockets, garage doors, etc.
- EAN 8595188183109 (key fob – black + Universal dimmer, 1-channel)
- EAN 8595188183116 (key fob – white + Universal dimmer, 1-channel)
- EAN 8595188183123 (key fob – black + 2 x Universal dimmer, 1-channel)
- EAN 8595188183130 (key fob – white + 2 x Universal dimmer, 1-channel)
The individual elements in the iNELS set are paired and their functions are
preset. iNELS kit with key fob enables the basic function of controlling
electrical appliances – ON / OFF. The appliances can be controlled
independently by a key fob.
Controller
Controller – key fob RF KEY-40/W, RF KEY-40/B
- RF KEY 40/B – key fob , black
- RF KEY 40/W – key fob , white
Characteristics
- Key fob-sized remote control – used to control, lights, gate, garage door, shutters, etc.
- 4 buttons, each of which allows you to control an unlimited number of components.
- Replaceable battery (3 V CR 2032 – included in the package) with a service life of approx. 5 years (depen-ding on the frequency of use).
Insertion and replacement of a battery RF KEY-40
Safe handling
When handling a device unboxed it is important to avoid contact with
liquids. Never place the device on the conductive pads or objects, avoid
unnecessary contact with the components of the device.
Technical parameters
RF KEY-40
| Supply voltage: | 3 V battery CR2032 |
|---|---|
| Battery life: | about 5 years depending on the frequency of use |
| Transmission indication: | red LED |
| Number of buttons: | 4 |
| Communication Protocol: | RFIO2 |
| Frequency: | 868.5 MHz |
| Signal transmission method: | one-way addressed message |
| Range: | in the open up to 200 m |
Other data
Operating temperature:| -10 … +50 °C (14 … 122 °F)
Operating position:| any
Colour design| white, black
Protection:| IP20
Pollution degree:| 2
Dimensions:| 64 x 25 x 10 mm
Weight:| 16 g
Related standards:| EN 60669, EN 300 220, EN 301489,
No 426/2000 Coll.
Attention
When you install iNELS RF Control system, you have to keep a minimum distance
of 1 cm (0.4“) between each unit. Between the individual commands must be an
interval of at least 1s.
Universal
Universal dimmer, 1-channel RFDEL-71B-SL
Characteristics
- The universal built-in dimmer is used to regulate light sources.
- They can be combined with detectors, controllers, iNELS RF Control or system components.
- 7 light functions – smooth increase or decrease with time setting 2s-30 min. + additional function SWITCH OFF
- Thanks for setting the min.the brightness you will eliminate fl ashing of the LED and ESL light sources
- The universal dimmer may be controlled by up to 25 channels (1 channel represents 1 button).
- The connection of the existing button on the control input “S“ enables the combination of wireless control with classic (wired) control.
- The programming button on the controller is also used for manual control of the output.
- For components labeled as iNELS RF Control2 (RFIO2), it is possible to set the repeater function via the RFAF/USB service device.
- Range up to 200 m (in open space), if the signal is insufficient between the controller and unit, use the signal repeater RFRP-20 or protocol component RFIO2 that supports this feature.
Installation options
Technical parameters
RFDEL-71B-SL
| Supply voltage: | 230 V AC / 50 Hz |
|---|---|
| Apparent power: | 5 VA |
| Dissipated power: | 0.5 W |
| Supply voltage tolerance: | +10/ -15 % |
| Connection: | 4 – wire, with NEUTRAL |
| Dimmed load: | R, L, C, LED, ESL |
Output:
Contactless:| 2 x MOSFET
Load capacity:| 300 W *
Control:
RF command from the transmitter:| 868.5 MHz
Range in open space:| up to 200 m
Manual control:| button PROG (ON/OFF), external button
Other data:
Operating temperature:| -15 … + 45 °C
Storage temperature:| -30 … +70°C
Operating position:| any
Protection:| IP30 under normal conditions
Overvoltage category:| III.
Contamination degree:| 2
Connection:| screwless terminals
Connecting conductor:| 0.2-1.5 mm2
Dimensions:| 43 x 44 x 22 mm
Weight:| 30 g
Related standards:| EN 60730, EN 63044, EN 300 220, EN 301 489
Compatibility
The device can be combined with all system components, controls, and devices
of iNELS RF Control and iNELS RF Control2. The detector can be assigned an
iNELS RF Control2 (RFIO2) communication protocol.
Connection
Radiofrequency signal penetration through various construction materials
Range up to 200 m in open space, if the signal is insufficient between the
controller and unit, use the signal repeater RFRP-20 or protocol component
RFIO2 that supports this feature.
Warning
The instruction manual is designated for mounting and also for the usage of the device. It is always a part of its packing. Installation and connection can be carried out only by a person with adequate professional qualifi cation with an understanding of this instruction manual and functions of the device, and while observing all valid regulations. The trouble-free function of the device also depends on transportation, storage, and handling. In case you notice any sign of damage, deformation, malfunction, or missing part, do not install this device and return it to its seller. It is necessary to treat this product and its parts as electronic waste after its lifetime is terminated. Before starting the installation, make sure that all wires, connected parts, or terminals are de-energized.
While mounting and servicing observe safety regulations, norms, directives, and professional, and export regulations for working with electrical devices. Do not touch parts of the device that are energized – life threat. Due to the transmissivity of RF signals, observe the correct location of RF components in the building where the installation is taking place. RF Control is designated only for mounting in interiors. Devices are not designated for installation in exteriors and humid spaces. They must not be installed into metal switchboards and into plastic switchboards with metal doors – transmissivity of RF signal is then impossible. RF Control is not recommended for pulleys etc. – the radio-frequency signal can be shielded by an obstruction, interfered with, a battery of the transceiver can get fl at, etc., and thus disable the remote control.
Designed & manufactured by:
ELKO EP, s.r.o. Palackého 493, 769 01 Holešov, Všetuly, Czech republic
www.elkoep.com, Hotline: +420 800 100 671.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>