inELS RF KEY 40 60 Key Fob Controller Instruction Manual
- June 3, 2024
- inELS
Table of Contents
02-9/2021 Rev.0
RF KEY – 40/60
4/6 button controller – keychain
Characteristics
- Key fob-sized remote control, available in black and white.
- When the button is pressed, it sends the set command (ON / OFF, dimming, time on / off, lower / raise).
- RF KEY-40: 4 buttons, each of which allows you to control an unlimited number of components.
- RF KEY-60: 6 buttons, each of which allows you to control an unlimited number of components.
- Replaceable battery (3 V CR 2032) with a service life of approx. 5 years (depending on the frequency of use).
Control options
The RF controllers can control all switching and dimming components of the RF
Control system, which are marked with the RFIO and RFIO2 communication
protocols.
RF controlers can control:
-
switches
RFSA-11B, RFSA-61B, RFSA-62B, RFSA-61M, RFSA-66M, RFSAI-61B, RFSAI-62B, RFSC-11, RFSC-61, RFUS-11, RFUS-61, RFJA-12B -
dimmers
RFDA-73/RGB, RFDA-11B, RFDA-71B, RFDEL-71B, RFDEL-71M, RFDSC-11, RFDSC-71, RFDAC-71B -
lighting
RF-RGB-LED-550, RF-White-LED-675
Radio frequency signal penetration through various construction materials
| | | |
---|---|---|---|---
80 – 95 %| 80 – 90 %| 60 – 90 %| 20- 60 %| 0 – 10 %
wooden structures with plaster boards| common glass| brick walls| reinforced
concrete| metal partitions
Indicators, settings
After inserting the battery, the red LED lights up continuously for 3 seconds and then for 5 seconds, the selected controller function is indicated by fl ashing LED.
- double fl ash – standard RFIO 2 operating mode
- rapid flashing – mode of compatibility with older actuators
If you do not want to change the function of the controller, you must not press any buttons during this time
To switch between RFIO2 mode and compatibility mode: If you need to change the
operating mode of the controller, after inserting the battery, when the LED is
constantly lit. press buttons 1 and 3 simultaneously and hold until the LED
starts to signal the changed mode (double flash or rapid flash). Then the
buttons must be released. The selected function mode is stored in memory and
after replacing the battery, the controller continues to operate in the same
mode.
If the controller is used in RFIO2 mode, then it is necessary to instruct the
controller and link to the actuators switch to learn mode not only the
actuator (according to the instructions for the actuator), but also the
controller in the following way: Remove the battery from the remote control,
press one of the buttons several times to discharge the device, and insert the
battery again. When the LED lights up, press button 1 and keep it pressed
until the controller starts signaling the learning mode with short fl ashing
LEDs. Then release the button and the button now works in RFIO2 learning mode.
To end the learning mode, remove the battery, press some of the buttons
several times. and then replace the battery. Now we press any button and the
controller will start again in RFIO2 operating mode.
Insertion and replacement of a battery
Use a coin to open the key fob and remove the front cover. Carefully tap the device out of the bottom cover.
Slide the CR2032 battery into the battery holder. Observe the polarity.
Insert the device into the bottom cover. Attach the front of the cover and click.
Technical parameters
Supply voltage: | 3 V battery |
---|---|
Battery life: | about 5 years depending on the frequency of use |
Transmission indication: | red / rote LED |
Number of buttons: | 4 |
Communication Protocal: | RF102 |
Frequence: | 866-922 MHz |
Signal transmission method: | one-way addressed message |
Range: | in the open up to 200 m |
Other data | |
Operating temperature: | -10 … +50 °C |
Operating position: | any / beliebig |
Colour design: | white, black /WeiB, schwarz |
Protection: | IP20 |
Pollution degree: | 2 |
Dimensions: | 71 x 31 x 8 mm |
Weight: | 17 g |
Related standards: | EN 60669, EN 300220, EN 301489 R&TTE Directive, Order. No |
426/2000 Coil. (Directive 1999/K) / EN 60669, EN 300220, EN 301489 Richtlinie RITE, RG Nr.426/2000 Sgl. (Riditlinie 1999/EG)
Attention:
When you instal iNELS RF Control system, you have to keep minimal distance 1
cm between each units.
Between the individual commands must be an interval of at least 1s.
Safe handling
When handling a device unboxed it is important to avoid contact with liquids.
Never place the device on the conductive pads or objects, avoid unnecessary
contact with the components of the device.
Warning
Instruction manual is designated for mounting and also for user of the device. It is always a part of its packing. Installation and connection can be carried out only by a person with adequate professional qualifi cation upon understanding this instruction manual and functions of the device, and while observing all valid regulations. Trouble-free function of the device also depends on transportation, storing and handling. In case you notice any sign of damage, deformation, malfunction or missing part, do not install this device and return it to its seller. It is necessary to treat this product and its parts as electronic waste after its lifetime is terminated. Before starting installation, make sure that all wires, connected parts or terminals are de-energized. While mounting and servicing observe safety regulations, norms, directives and professional, and export regulations for working with electrical devices. Do not touch parts of the device that are energized – life threat. Due to transmissivity of RF signal, observe correct location of RF components in a building where the installation is taking place. RF Control is designated only for mounting in interiors. Devices are not designated for installation into exteriors and humid spaces. The must not be installed into metal switchboards and into plastic switchboards with metal door – transmissivity of RF signal is then impossible. RF Control is not recommended for pulleys etc. – radiofrequency signal can be shielded by an obstruction, interfered, battery of the transceiver can get fl at etc. and thus disable remote control.
ELKO EP declares that the RF KEY type of radio equipment complies with
Directive 2014/53 / EU.
The full EU Declaration of Conformity is available at:
www.elkoep.com/4-channel-controller—keychain-white
ELKO EP, s.r.o., Palackého 493, 769 01 Holešov, Všetuly, Czech Republic
Tel.: +420 573 514 211, e-mail: elko@elkoep.com,
www.elkoep.com
ELKO EP, s.r.o. | Palackého 493 | 769 01 Holešov, Všetuly | Czech Republic |
e-mail: elko@elkoep.com | Support: +420 778 427 366
ELKO EP Germany GmbH | Minoritenstr. 7 | 50667 Köln | Deutschland | E-mail:
elko@elkoep.de | Tel: +49 (0) 221 222 837 80
ELKO EP Austria GmbH | Laurenzgasse 10/7 | 1050 Wien | Österreich |
www.elkoep.com /
www.elkoep.de
References
- 4-channel controller - keychain white • ELKO EP
- 4-tlačítkový ovladač - klíčenka RF Key bílá/černá • ELKO EP s.r.o
- ELKO EP - Hersteller von elektronischen Geräten • ELKO EP Germany
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>