Litiot MBP00 BLE Module User Manual

MBP00 BLE Module
User Manual

Version History

Description

1.1Overview This is UART to BLE 5.0/5.1 module. It is composed of a highly wireless chip with Arm Cortex-M0, internal 512 KB Flash and 64KB SRAM. The antenna is build-in PCB with 2dbi gain. It has high stability and ultra-low sleep power consumption, about 1.1uA in deep sleep model. For the ice water meter, the module supports the low power management, it can work over 10 years with battery.
The module supports point-to-point and the multi-slave connection function binding 5 to 15 slave devices directly. With the BLE mesh, it can build the network over 200
nodes.

1.2 RF Feature

• Bluetooth 5.0/5.1 Compliant, 125Kbps,500kbps,1Mbps and 2Mbps.
• Bluetooth SIG Mesh and private Mesh.
• Rx Sensitivity: 99.7 dBm @1Mbps,97 dBm @2Mbps,105dBm @125kbps.
• Tx Output Power:up to 12 dBm.

1.3Feature Of Power Management Module

• Power Supply:1.8V～3.6V, Type 3.3V
• RX Power Consumption:4.3 mA Peek
• TX Power Consumpton:4.5 mA @0dBm Peek
• Ultra-low Sleep Power Consumption:1.1 uA (RTC +GPIO Wake Up)
• Shutdown Power Consumptoin:700 nA (GPIO Wake Up)

1.4 Security

• AES Security Module(64/128/192)
• Elliptical Curve Cryptography(256)
• Triple Data Encryption Standard(T/DES)
• True Random Number Generator(RNG)
• Application layer Security via App

1.5 User Interface

• UART*1
• SWD*1
• GIPO*6

Pin Description

2.1 Pin Diagram

2.2 Pin Definition

﹡ Support SWD and UART programming. Push the Boot pin high, and then do the Uart programming.

Reference Design

Notes:

• 3.3V stable, minimum ripple wave with DC-DC or LDO power supply
• Maximum distance between BLE model and power/high-freq layout.
• Avoid high- freq signal lines/power lines close or beneath the MPB00 model.
• Place the antenna on clearance area without any components.
• UAR default power is 3.3V TTL.

FCC Requirement
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits .pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable   protectionagainst harmful interference in a residential installation. This equipment generates, uses, and canradiate radio frequency energy, and if not installed and used in  ccordance with the instructions,may cause harmful in terference to radio communications. However, there is no guarantee that interference will not occur in a particular  installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF exposure considerations This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co- located or operating in conjunction with any other antenna or transmitter.
RF Exposure – This device is only authorized for use in a mobile application. At least 20 cm of separation distance between the module and the user’s body must be  maintained at all times.
A label must be affixed to the outside of final commercial product with the following statements:
This device contains FCC ID:2AWSF-MBP00
Consistent with §2.909(a), the following text must be included within the user’s manual or operator instruction guide for the final commercial product.
This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in  conjunction with any other antenna or transmitter.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>