inELS 8319 Wireless Shutter Control Key Fob User Manual

: June 3, 2024
: inELS

Table of Contents

8319 Wireless Shutter Control Key Fob
Controller – key fob RF KEY-40
Technical parameters
Switch unit for shutters RFJA-32B-SL
Connection
Read User Manual Online (PDF format)
Download This Manual (PDF format)

WIRELESS SHUTTER
CONTROL KEY FOB
User Manual

8319 Wireless Shutter Control Key Fob

Combination of iNELS Key Fob and shutter switching device to control garage doors, gates, blinds and awnings
Package

| Controller – key fob RF KEY-40/W, RF KEY-40/B
---|---
| Switch unit for shutters RFJA-32B-SL

EAN 8595188183192 (Controller – key fob Black + 2 x Switch unit for shutters)
EAN 8595188183208 (Controller – key fob White + 2 x Switch unit for shutters)
inELS 8319 Wireless Shutter Control Key Fob - Figure 1 The individual elements in the iNELS set are paired and their functions are preset.
iNELS kit for shutters enables it´s remote control.
The settings of the wall controllers can be changed – see detailed manuals of iNELS elements.

Controller – key fob RF KEY-40

Detailed manual
RF KEY 40
https://www.elko.li/rfkey-40

RF KEY 40/B – 4 button controller – keychain (remote control), black
RF KEY 40/W – 4 button controller – keychain (remote control), white
Characteristics

Key fob-sized remote control – used to control, lights, gate, garage door, shutters, etc.
4 buttons, each of which allows you to control an unlimited number of components.
Replaceable battery (3 V CR 2032 – included in the package) with a service life of approx. 5 years (depending on the frequency of use).

Insertion and replacement of a battery RF KEY-40

| inELS 8319 Wireless Shutter Control Key Fob - Figure
4 |
---|---|---
Use a coin to open the key fob and remove the front cover. Carefully tap the device out of the bottom cover.| Slide the CR2032 battery into the battery holder. Observe the polarity.| Insert the device into the bottom cover. Attach the front of the cover and click.

Safe handling
When handling a device unboxed it is important to avoid contact with liquids. Never place the device on the conductive pads or objects, avoid unnecessary contact with the components of the device.

Technical parameters

RF KEY-40

Supply voltage:	3 V battery CR 2032
Battery life:	about 5 years depending on the frequency of use
Transmission indication:	red LED
Number of buttons:	4
Communication Protocol:	RFIO2
Frequency:	868,5 MHz
Signal transmission method:	one-way addressed message
Range:	in the open up to 200 m

Attention
When you install iNELS RF Control system, you have to keep a minimal distance of 1 cm (0.4“) between each unit. Between the individual commands must be an interval of at least 1s.

Switch unit for shutters RFJA-32B-SL

**Detailed manual

RFJA-32B-SL
**https://www.elko.li/rfja-32b-sl

Characteristics

The switching unit for blinds has 2 output channels used to control garage doors, gates, blinds, awnings, etc…
It can be combined with system components iNELS RF Control² with RFIO² protocol.
The BOX design lets you mount it right in an installation box, a ceiling or motor drive cover.
Short presses of the controller enable tilting of lamellas, and a long press enables you to draw the blinds up or down to the end position.
Each of the units may be controlled by up to 25 channels (1 channel represents one assigned controller).
The programming button on the unit is also used for manual control of the output.
For components it is possible to set the repeater function via the RFAF / USB service device.
Range up to 200 m (in open space), if the signal is insuffi cient between the controller and unit, use the signal repeater RFRP-20 or protocol component RFIO² that support this feature.
Communication frequency with bidirectional protocol iNELS RF Control² (RFIO²).

Installation options inELS 8319 Wireless Shutter Control Key Fob -
Figure 6 Technical parameters
RFJA-32B-SL

Supply voltage:	230 V AC / 50 – 60 Hz
Apparent input:	7 VA / cos p = 0.1
Dissipated power:	0.7 W
Supply voltage tolerance:	+10 -15 %

Connection

Indication, manual control

LED STATUS – indication of the device status.
Manual control is performed by pressing the PROG button.
Programming is performed by pressing the PROG button for more than 1s.
Terminal block for connection of buttons. IN1 – direction button up IN2- button down.

In the programming and operating mode, the LED on the component lights up at the same time each time the button is pressed – this indicates the incoming command inELS 8319 Wireless Shutter Control Key Fob - Figure
8

LED / button PROG
Addresses for individual relays (channels)
Terminal block – connection for external button
Terminal block – connecting the neutral conductor
Terminal block – load connection
Terminal block for connecting the phase conductor

Radiofrequency signal penetration through various construction materials
Range up to 200 m in open space, if the signal is insuffi cient between the controller and unit, use the signal repeater RFRP-20 or protocol component RFIO² that supports this feature.
inELS 8319 Wireless Shutter Control Key Fob - Figure 9 Warning
Instruction manual is designated for mounting and also for the usafe of the device. It is always a part of its packing. Installation and connection can be carried out only by a person with adequate professional qualiﬁ cation with understanding this instruction manual and functions of the device, and while observing all valid regulations. Trouble-free function of the device also depends on transportation, storing and handling. In case you notice any sign of damage, deformation, malfunction or missing part, do not install this device and return it to its seller. It is necessary to treat this product and its parts as electronic waste after its lifetime is terminated. Before starting installation, make sure that all wires, connected parts or terminals are de-energized. While mounting and servicing observe safety regulations, norms, directives and professional, and export regulations for working with electrical devices. Do not touch parts of the device that are energized – life threat. Due to transmissivity of RF signal, observe correct location of RF components in a building where the installation is taking place. RF Control is designated only for mounting in interiors. Devices are not designated for installation into exteriors and humid spaces. The must not be installed into metal switchboards and into plastic switchboards with metal door – transmissivity of RF signal is then impossible. RF Control is not recommended for pulleys etc. – radiofrequency signal can be shielded by an obstruction, interfered, battery of the transceiver can get ﬂ at etc. and thus disable remote control.