intempo EE7047 Active Noise Cancelling Headphones Instruction Manual
- June 11, 2024
- intempo
Table of Contents
intempo EE7047 Active Noise Cancelling Headphones
Description of Parts
- Bluetooth Headphones
- Cushioned earcups
- LED indicator light
- Skip/Volume + button (+)
- Skip/Volume – button (-)
- Play \ Pause\ Hand-free button (o)
- Built-in hands-free microphone
- USB Type-C 5 Y = charging port
- Aux. input port
- USB Type-Charging cable
- Line-in Aux. coble
- ANC switch
Safety Instructions
- When using electrical products, basic safety precautions should always be followed.
- Keep the product and its accessories out of the reach of children.
- Keep small parts away from children as these may present a choking hazard.
- Children under B years should be supervised to ensure that they do not ploy with the product.
- This product is not a toy.
- This product contains no user serviceable ports. If the product and any of its accessories are malfunctioning or damaged, the product should he recycled.
- Keep the product and its accessories away from heat sources, direct sunlight, humidity, water and any other liquid, or sharp edges that could cause damage.
- Ensure the product is well-ventilated.
- Do not leave any objects susceptible to magnetism (cosh, cords ek.) near the product.
- Do not operate the product with wet hands.
- Do not operate the product if has been exposed to water, moisture or any other liquid, to prevent against electric shock, explosion and/or injury to yourself and damage to the product.
- Do not use the product for anything other than its intended use. Do not use any accessories other than those supplied. Do not put objects into any of the openings. This product is intended for domestic use only. It should not be used for commercial purposes. To prevent possible hearing damage, do not listen at high volume levels for long periods of time – this . may also damage the product.
NOTE: It is advised that the product is to not be used whilst charging, as this could reduce the life of the battery.
Battery Safety
- The supply terminals are not to be short-circuited. In the event of a battery and cell leaking, do not allow the liquid to come in contact with the skin or eyes.
- If contact has been made, wash the affected area with copious amounts of water and seek medical advice.
- Secondary cells and batteries need to be charged before use.
- After extended periods of storage, it may be necessary to charge and discharge the cells or batteries several times to obtain maximum performance.
- Keep batteries out of the reach of children.
- Do not crush, puncture, dismantle or otherwise damage batteries.
- Do not store above 60 °C. Avoid storage in direct sunlight.
- Do not dispose of exhausted batteries in household waste.
- Do not expose the batteries to heat or fire as they may explode.
- Once the batteries have been exhausted, dispose of the product at a local recycling station.
- Contact the local government offices for further details.
- This product is fitted with a 3.7 V 300 mAh li-ion rechargeable battery (non-removable).
Declaration of Conformity
UP Global Sourcing UK Ltd. hereby declares that this unit is in compliance
with the essential requirements and other provisions of directive 2014/53/EU.
The declaration of conformity may be consulted at UP Global Sourcing UK Ltd.,
Victoria Street, Manchester OL9 ODD. UK. Edmund-Rumpler Straße 5, 51149 Köln.
Germany. or online at http://www.intempo.co.uk/declaration-letters.html.
Model No.: EE7047.
Disposal of Waste Batteries and Electrical and Electronic Equipment
This symbol on the product, its batteries or its packaging means that this
product and any batteries it contains must not be disposed of with household
waste. Instead, it is the user’s responsibility to hand this over to an
applicable collection point for the recycling of batteries and electrical and
electronic equipment. This separate collection and recycling will help to
conserve natural resources and prevent potential negative consequences for
human health and the environment due to the possible presence of hazardous
substances in batteries and electrical and electronic equipment, which could
be caused by inappropriate disposal. Some retailers provide take-back services
which allow the user to return exhausted equipment for appropriate disposal.
It is the user’s responsibility to delete any data on electrical and
electronic equipment prior to disposal. For more information about where to
drop batteries, electrical and electronic waste off, please contact the local
city/ municipality office, household waste disposal service, or the retailer.
Care and Maintenance
Wipe the headphones with a soft, lint-free cloth and allow to dry thoroughly.
DO NOT:
Use any abrasive cleaning solvents to clean the headphones.
Expose the headphones to extremely high or low temperatures.
Drop the product.
Attempt to disassemble the product.
Dispose of the product in a fire as it will result in an explosion.
Instructions for Use
Charging the Battery
The headphones are fitted with a 3.7 V 300 mAh rechargeable li-ion battery. It
is recommended that the battery is charged fully before first use; this will
take approx. 5 hours.
Connect the Type- end of the USB charging cable into the USB Type-C charging
port on the headphones and the other end to a compatible USB port.
Whilst charging, the LED indicator light will illuminate red. Once the battery
has charged fully, the LED indicator light will turn off.
Once the headphones are fully charged, carefully disconnect both ends of the
USB charging cable and store it safely for future use.
“Maximum play time of 35 hours is based on 20 % volume with ANC mode off.
Maximum playtime of 22 hours is based on 20 % volume with ANC mode on.
Using the Bluetooth Headphones
Basic Functionality
- Turn on the headphones by pressing and holding ‘O’ for approx. 2 seconds. The headphones will emit a tone to signal that the headphones are switched on.
- Pause the track by pressing ‘O’; push it again to resume the track.
- Adjust the volume of the headphones using ‘+’ and ‘-‘.
- Press and hold ‘+’ to increase the volume; decrease the volume by pressing and holding ‘-‘.
- To switch to the next track, press ‘+’; play the previous track by pressing ‘-‘.
- Press and hold ‘o’ for approx. 5 seconds to turn headphones off.
The headphones will emit a tone to signal that headphones are switched off.
Modes
The headphones must be turned on before using any of the following modes.
Bluetooth Mode
- STEP 1: Once the headphones are turned on, the LED indicator light will flash blue and red to signal that they are ready to be paired with a Bluetooth compatible device.
- STEP 2: Search for the headphones using a Bluetooth compatible device. Select ‘EE7047’ to connect and pair. Once a connection has been made, the LED indicator light will switch off to signal that the devices are paired.
- STEP 3: To unpair or remove a Bluetooth compatible device from the headphones, turn off the Bluetooth function on the compatible device. The headphones can now be paired with a new compatible device.
NOTE: Once connected, sound can be controlled using either the headphones or the relevant controls on the Bluetooth compatible device.
Active Noise Cancellation (ANC Mode)
To turn on ANC mode, move the ANC switch; the LED indicator light will
illuminate green to signal that ANC mode has been activated. To turn off ANC
mode, move the ANC switch in the opposite direction; the LED indicator light
will turn off to signal that ANC mode has been deactivated.
NOTE: Do not leave ANC mode advice whilst the headphones are not in use
as this will drain the battery. ANC mode is effective for up to 25 dB.
Making Phone Calls via a Bluetooth Compatible Device
Once the Bluetooth compatible device has been paired with the headphones,
phone calls can be made.
- STEP 1: Using the Bluetooth compatible device, dial the number to be called and select the Bluetooth hands- free option. The built-in microphone on the headphones will now act as a hands-free device.
- STEP 2: To connect a call using the headphones, press ‘O’; to disconnect a call press and hold ‘o’.
- STEP 3: Reject an incoming call by pressing and holding ‘O’ for approx. 2 seconds.
- STEP 4: Redial the last number called by pressing ‘O’ twice.
NOTE: The volume of the phone call can be controlled using either the headphones or the Bluetooth compatible device.
Aux. Mode
Connect one end of the line-in Aux. cable to the Aux. input port on the
headphones and the other end to a compatible audio source. The headphones will
automatically switch to Aux. mode once the line-in Aux. cable has been
inserted.
NOTE: Once connected, sound can be controlled using the relevant controls
on the compatible device. The headphones cannot be used to skip tracks during
Aux. mode.
Troubleshooting
The headphones have no power.
The headphones have run out of charge. Charge the headphones following the
instructions in the section entitled ‘Charging the Battery’.
The headphones have no sound.
The volume level is set too low. Check that the volume level is set at an
audible level and adjust accordingly on the connected device. The headphones
are not paired with a Bluetooth compatible device. Follow the instructions in
the section entitled ‘Bluetooth Mode’.
Unable to pair a device with the headphones.
The Bluetooth device is not compatible with the headphones. Check that the
Bluetooth device is compatible with the headphones and that the Bluetooth
function is switched on.
The charge of the headphones depletes quickly.
The volume level is set too high. Excessive use of the headphones at high
volumes will drain the battery quickly. Charge the headphones following the
instructions in the section entitled ‘Charging the Battery’ and listen at a
lower volume for better results. The battery may be reaching the end of its
service life and the headphones will need to be disposed of. Follow the
instructions in the section entitled ‘Battery Safety’. ANC mode is active;
battery life will drain quicker whilst ANC mode is activated.
Specifications
- Product code: EE7047
- Bluetooth version: 5.3
- Impedance: 32 2 Sensitivity: 95 ‡ 3 dB
- Frequency response: 20 Hz-20 kHz
- Bluetooth frequency: 2.4-2.48 GHz
- Max RF output: < 6 dBm
- Effective range may be reduced to the presence of obstacles between connected devices.
The Bluetooth® word, mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks are under license. Other trademarks and trade names are those of their respective owners.