Laserliner 081.257A DigiLevel Laser G80 Digital Electronic Level Instruction Manual
- June 4, 2024
- Laserliner
Table of Contents
Laserliner 081.257A DigiLevel Laser G80 Digital Electronic Level
Note:
Completely read through the operating instructions, the „Warranty and Additional Information“ booklet as well as the latest information under the internet link at the end of these instructions. Follow the instructions they contain. This document must be kept in a safe place and passed on together with the device.
Function / application
Digital electronic spirit level with green laser technology
- Wall line laser to optically extend the measurement area
- Horizontal and vertical angle display
- The slope memory allows angles to be easily transferred
General safety instructions
-
The device must only be used in accordance with its intended purpose and within the scope of the specifications.
-
The measuring tools and accessories are not toys.
Keep out of reach of children. -
Modifications or changes to the device are not permitted, this will otherwise invalidate the approval and safety specifications.
-
Do not expose the device to mechanical stress, extreme temperatures, moisture or significant vibration.
-
The device must no longer be used if one or more of its functions fail or the battery charge is weak.
Safety instructions
Using class 2 lasers
- Attention: Do not look into the direct or reflected beam.
- Do not point the laser beam towards persons.
- If a person‘s eyes are exposed to class 2 laser radiation, they should shut their eyes and immediately move away from the beam.
- Under no circumstances should optical instruments (magnifying glass, microscope, binoculars) be used to look at the laser beam or reflections.
- Do not use the laser at eye level (1.40 … 1.90 m)
- Reflective, specular or shiny surfaces must be covered whilst laser devices are in operation.
- In public areas shield off the laser beam with barriers and partitions wherever possible and identify the laser area with warning signs.
DigiLevel Laser G40/G80
Laser outlet
Safety instructions
Dealing with electromagnetic radiation
- The measuring device complies with electromagnetic compatibility regulations and limit values in accordance with EMC-Directive 2014/30/EU.
- Local operating restrictions – for example, in hospitals, aircraft, petrol stations or in the vicinity of people with pacemakers – may apply. Electronic devices can potentially cause hazards or interference or be subject to hazards or interference.
- The measuring accuracy may be affected when working close to high voltages or high electromagnetic alternating fields.
Green laser technology
Devices with the PowerGreen+ technology have very bright, green high-
performance diodes which provide outstanding visibility of the laser lines at
great distances, on dark surfaces and in bright ambient lighting conditions.
Approx. 6 times brighter than a typical red laser with 630 – 660 nm
Inserting batteries
Open the battery compartment and insert batteries according to the symbols. Be sure to pay attention to polarity.
Parts Description
- Change units of measure
- Angle reference value setting
- Calibration
- ON/OFF button
- Hold function
- Acoustic signal generator / Backlighting ON/OFF
- Slope direction
- Acoustic signal generator active
- HOLD: current measured value is held
- Angle reference set
- Battery charge
- Slope angle
- Units of measure
- Line laser
- Horizontal vial
- Vertical vial
- Magnets
- Measuring surface
- Battery compartment (Rear)
Switching on and measuring
Note: Make sure that the reference function is deactivated before measuring.
The DigiLevel Laser G40 / G80 can measure angles continuously to 360°.
- Switch the DigiLevel Plus on using the on/off switch (4).
- The slope angle is shown in the display (8). If slopes are measured overhead, the direction of display adjusts automatically.
- The current slope direction is also shown by the symbol (7).
Selection of unit of measurement
Button (5) allows the desired unit of measurement to be selected (° degrees, %, mm/m).
Calibration
- Place the unit with its measuring edge (18) down on a straight surface and mark the positions of the unit‘s ends on the underlying surface (see Fig. below). Switch the unit on (4) and press the CAL button (3) until CAL 1 will appear in the display.
- Press the CAL button (3) again. CAL 1 flashes. The display then changes to CAL 2.
- Now turn the unit around vertically (end-for-end) by 180° such that its ends are positioned opposite where they previously were but again exactly at the underlying surface marks (reverse measurement). Again press the CAL button (3). CAL 2 flashes. Calibration is concluded when the measured value appears on the display.
Note: The unit is properly calibrated when it displays the same measurement value, i.e. the underlying surface‘s deviation from absolute level, in both positions (0° and 180°).
Changing the angle reference value
With button (2), it is possible to transfer angles elsewhere. To do so, set
the device to the desired slope and press button (2). The display then changes
to „0.0°“, „REF“ flashes on the display and the required reference angle is
set. The slope can now be transferred to other objects.
Press button (2) again to deactivate the angle reference.
Note: The angle reference is not deactivated by switching off the device.
6 °C / °F / measured value
The ambient temperature is shown in °C and °F by briefly pressing the CAL
button (3). Press again to switch back to the measured value.
HOLD
Press the HOLD button (5) to hold the current measured value on the display.
Acoustic signal
The acoustic signal can be switched on or off with button (6). When the angle
of slope stands at 0°, 45°, 90° or the most recently stored value, this is
indicated by an acoustic signal.
Note: When working with a changed angle reference value, the acoustic
signal is activated on reaching the new reference value (0°, 45°, 90°
display).
Backlighting
The backlighting is switched ON/OFF by pressing and holding button (6).
Auto Off function
In order to preserve the batteries, the measuring device switches off
automatically if it is left idle for 3 minutes.
Information on maintenance and care
Clean all components with a damp cloth and do not use cleaning agents,
scouring agents and solvents. Remove the battery(ies) before storing for
longer periods. Store the device in a clean and dry place.
Calibration
The meter needs to be calibrated on a regular basis to ensure it produces
accurate measurement results. We recommend carrying out calibration once a
year. Contact your distributor or the UMAREX-LASERLINER service department.
Danger – powerful magnetic fields
Powerful magnetic fields can adversely affect persons with active medical
implants (e.g. pacemaker) as well as electromechanical devices (e.g. magnetic
cards, mechanical clocks, precision mechanics, hard disks).
With regard to the effect of powerful magnetic fields on persons, the
applicable national stipulations and regulations must be complied with such as
BGV B11 §14 „electromagnetic fields“
(occupational health and safety – electromagnetic fields) in the Federal
Republic of Germany.
To avoid interference/disruption, always keep the implant or device a safe
distance of at least 30 cm away from the magnet.
Technical data
Technical data
Electronic measuring precision
| ± 0.1° at 0° … 1°
± 0.1° at 89° … 90°
± 0.2° at 1° … 89°
Display accuracy| 1 decimal place
Vial| ± 0.5 mm/m
Laser class| 2 / < 1 mW
Laser wavelength| 515 nm
(EN 60825-1:2014/AC:2017)
Operating conditions
| 0°C … 40°C, max. humidity 80% rH, no condensation, max. working altitude
2000 m above sea level
Storage conditions| -10°C … 60°C,
max. humidity 85% rH
Auto power off| after 3 minutes
Power supply| 2 x 1.5V LR03 (AAA)
Dimensions (W x H x D) G40| 400 x 66 x 30 mm
Dimensions (W x H x D) G80| 800 x 66 x 30 mm
Weight G40 / G80| 566 g / 966 g (incl. batteries)
EU directives and disposal
This device complies with all necessary standards for the free movement of
goods within the EU.
This product is an electric device and must
be collected separately for disposal according to the European Directive on
waste electrical and electronic equipment.
Further safety and supplementary notices at:
http://laserliner.com/info?an=AHH
SERVICE
Umarex GmbH & Co. KG
– Laserliner –
Möhnestraße 149, 59755 Arnsberg, Germany Tel.: +49 2932 638-300, Fax: +49 2932
638-333 info@laserliner.com
Umarex GmbH & Co. KG Donnerfeld 2
59757 Arnsberg, Germany
Tel.: +49 2932 638-300, Fax: -333
www.laserliner.com