INTELLINET 508827 8 Port Gigabit Ethernet Industrial Switch with 2 SEP Ports Instructions
- June 3, 2024
- INTELLINET
Table of Contents
8-Port Gigabit Ethernet Industrial Switch with 2 SFP Ports Instructions
Model 508827
(IIS-8G02) Important: Read before use.
Importante: Leer antes de usar.
508827 8 Port Gigabit Ethernet Industrial Switch with 2 SEP Ports
For additional benefits:
Scan to register your product warranty
or go to: register.intellinet-network.com/r/508827
https://register.intellinet-network.com/r/508827
Instructions
The Intellinet 8-Port Gigabit Ethernet Industrial Switch with 2 SFP Ports
offers an array of time-saving, cost-effective features while providing
superior network
throughput. No configuration is required and installation is plug and play.
Features
- Provides RJ45 data connections for up to eight network devices
- IP40 slim-type metal housing to withstand harsh industrial conditions
- Wide operating temperature: -40 – 75°C (-40 – 167°F)
- Option for DIN-rail installation
- Two small form-factor pluggable GBIC module slots (SFP)
- Two redundant DC inputs (12 – 48 V) with I/O terminal block With a backplane speed of 20 Gbps, plenty of performance is available for your computers, servers and other networking devices. Each of the ports automatically senses the link speed of the connected network device and adjusts to 10, 100 or 1000 Mbps for compatibility and maximum performance. For specifications, visit intellinetnetwork.com. Register your product at register. intellinet-network.com/r/508827 or scan the QR code on the cover.
LEDs
| LED | Color | Status | Status Description |
|---|---|---|---|
| PWR | Green | On | Power on |
| Off | Power off | ||
| Link/Act 1 8 / SFP 1 &2 | Green | On | Valid port connection |
| Blinking | Sending or receiving data | ||
| Off | No link established |
Cat5e/6/6a UTP/STP cables provide optimal performance; if a status LED doesn’t indicate a link or activity, check the corresponding device for proper setup and operation.
Power
Chassis Ground Column
Located on the side of the power supply connector, a grounding terminal
connector is used to provide proper grounding for your Intellinet Network
Solutions switch. It should be wired to an object that provides earth ground.
Terminal Block Installation
NOTE: Ensure all power is off/disconnected before beginning!
- Loosen appropriate screws.
- Insert bare power-supply wires into appropriate terminal slots (positive wire into positive slot; negative wire into negative slot).
- Tighten appropriate screws to secure wires. (If desired, repeat steps 1 – 3 on second input pair.)
- Install block into the device and tighten screws.
Power Off Alarm
You can choose whether to connect the power failure warning device to the
connecting terminal marked “Fault” according to your requirements. When using
power redundancy, if one power source fails, a fault alarm will be generated.
Placement
Desktop Installation
Prior to use, place/position the switch:
- on a level surface that can support the weight of the switch and that offers at least 25 mm (approx. 1”) of clearance for ventilation;
- away from sources of electrical noise: radios, transmitters, broadband amplifiers;
- within 100 m (approx. 328’) of network devices it’s to be connected to;
- where it cannot be affected by excessive moisture.
DIN-Rail Installation
- With DIN-rail bracket attached to device with screws, angle bracket onto DIN rail.
- Push device in till it clicks into place.
WASTE ELECTRICAL & ELECTRONIC EQUIPMENT
DISPOSAL OF ELECTRIC AND ELECTRONIC EQUIPMENT
(Applicable In The European Union And Other European Countries With
Separate Collection Systems)
This symbol on the product or its packaging means that this product must not
be treated as unsorted household waste. In accordance with EU Directive
2012/19/EU on
Waste Electrical and Electronic Equipment (WEEE), this electrical product must
be disposed of in accordance with the user’s local regulations for electrical
or electronic waste. Please dispose of this product by returning it to your
local point of sale or recycling pickup point in your municipality.
WARRANTY INFORMATION
intellinet-network.com
REGULATORY STATEMENTS
FCC Class A
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the Federal Communications Commission
(FCC) Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses and can radiate radio frequency
energy, and if not installed and used in accordance with the instruction
manual may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference,
in which case the user will be required to correct the interference at his own
expense. Any changes or modifications made to this equipment without the
approval of the manuafacturer could result in the product not meeting the
Class A limits, in which case the FCC could void the user’s authority to
operate the equipment.
CE
This device complies with the requirements of CE 2014/30/EU and / or
2014/35/EU. The Declaration of Conformity for is available at:
All trademarks and trade names are the property of their respective owners.
© IC Intracom. All rights reserved. Intellinet Network Solutions is a
trademark of IC Intracom, registered in the U.S. and other countries.
Printed on recycled paper.
INT_508827_QIG_0322_REV_5.11
support.intellinet-network.com/barcode/508827
North America
IC Intracom America 550 Commerce Blvd.
Oldsmar, FL 34677, USA
Asia & Africa
IC Intracom Asia
4-F, No. 77, Sec. 1, Xintai 5th Rd. Xizhi Dist., New Taipei City 221, Taiwan
Europe
IC Intracom Europe Löhbacher Str. 7, D-58553
Halver, Germany intellinetnetwork.com
References
- Intellinet Network Solutions - Provider of PoE and Data Center Product
- Intellinet Network Solutions - Provider of PoE and Data Center Product – Intellinet Solutions
- DropCatch.com
- Intellinet Network Solutions Account and Product Registration