INTELLINET 508988 Industrial Gigabit Media Converter and PoE+ Injector Instructions
- June 3, 2024
- INTELLINET
Table of Contents
INTELLINET 508988 Industrial Gigabit Media Converter and PoE+ Injector
For additional benefits
Scan to register your product warranty
or go to: register.intellinet-network.com/r/508988
Instructions
Media converters connect two Ethernet networks over a longer distance using fiber optic cable.
Features
- One 10/100/1000 RJ45 port supporting a maximum distance of 100 m (300 ft.)
- One SFP port for 1000Base-X optical transceiver modules and distances up to 120 km (75 mi.)
- Power over Ethernet injector function with output up to 30 watts
- IP40 slim-type metal housing to withstand harsh industrial conditions
- Option for DIN-rail installation
- Two redundant DC inputs (48 – 56 V) with terminal block
For specifications, visit intellinetnetwork.com. Register your product at register.intellinet-network.com/r/508988 or scan the QR code on the cover.
Placement
Desktop Installation
Prior to use, place/position the device:
- on a level surface that can support the device with at least 25 mm (approx. 1”) of clearance for ventilation;
- away from sources of electrical noise: radios, transmitters, broadband amplifiers;
- within 100 m (approx. 328’) of network devices it’s to be connected to.
DIN-Rail Installation
- Angle spring of mounting clip over top lip of DIN rail.
- Push device down till clip clicks onto rail.
- Ensure installation is stable.
Connections
This product requires an SFP transceiver module that provides fiber optic connections.
- Insert the transceiver into the media converter and route the fiber optic cable into the transceiver.
- Route the other end of the fiber optic cable into a suitable port in your fiber optic network.
Maximum length and fiber cable specification depend on the model.
RJ45 & PoE
Connect the UTP port of the media converter to powered RJ45 device; e.g., to a
network camera. Cat5e or better cabling is recommended. The Intellinet
Industrial Gigabit Media Converter and PoE+ Injector complies with IEEE
802.3at / 802.3af standards. The device can supply up to 30 watts of power to
a PoE-compliant powered device.
Power
Terminal Block Installation
NOTE : Ensure all power is off/disconnected before beginning!
- Loosen appropriate screws. Insert bare power-supply wires into appropriate terminals (positive wire into positive [V1+] terminal, negative wire into negative [V1-] terminal, ground wire to ground [GND] terminal).
- Tighten appropriate screws to secure wires. Repeat these steps for a second power supply if desired (V2+, V2-, GND).
- Install block into the device.
Front panel
LED
| LED | Color | Status | Description |
|---|---|---|---|
| P1/P2 | Green | On | Power channel is powered. |
| Off | Power channel is not powered. |
FX
| ****
Green
| On| Fiber port is connected.
Off| Fiber port is not connected.
Flashing| Sending or receiving data.
PoE| Yellow| On| PoE is being supplied to a connected PD.
Off| No power is being supplied to a connected PD.
L/A
| ****
Green
| On| Valid port connection.
Off| Connection not established.
Flashing| Sending or receiving data.
DIP Switch — LFPT/100M
| Switch | Position | Description |
|---|
LFPT
| ****
ON
| Link Fault Pass Through enabled: Devices on a link must acknowledge that
they are online before data can be transmitted. When one of the devices
doesn’t respond, data cannot be sent.
OFF| Link Fault Pass Through disabled
100M
| ON| Copper interface management — Restricts data transfer rate to 100Mbps
OFF| No data transfer rate restriction
WASTE ELECTRICAL & ELECTRONIC EQUIPMENT
DISPOSAL OF ELECTRIC AND ELECTRONIC EQUIPMENT
(Applicable In The European Union And Other European Countries With Separate Collection Systems) This symbol on the product or its packaging means that this product must not be treated as unsorted household waste. In accordance with EU Directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE), this electrical product must be disposed of in accordance with the user’s local regulations for electrical or electronic waste. Please dispose of this product by returning it to your local point of sale or recycling pickup point in your municipality
WARRANTY AT
REGULATORY STATEMENTS
Class A This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to Part 15 of the Federal Communications
Commission (FCC) Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and can radiate radio
frequency energy, and if not installed and used in accordance with the
instruction manual may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the
interference at his own expense. Any changes or modifications made to this
equipment without the approval of the manuafacturer could result in the
product not meeting the Class A limits, in which case the FCC could void the
user’s authority to operate the equipment CE This device complies with the
requirements of CE 2014/30/EU (UKCA Electromagnetic
Compatibility Regulations 2016) and / or 2014/35/EU (UKCA Electrical Equipment
[Safety] Regulations 2016). The Declaration of Conformity for is available at:
support.intellinet-network.com/barcode/508988
North America
IC Intracom America 550 Commerce Blvd. Oldsmar, FL 34677, USA
intellinet-network.com All trademarks and trade names are the property of their respective owners. © IC Intracom. All rights reserved. Intellinet Network Solutions is a trademark of IC Intracom, registered in the U.S. and other countries. intellinet-network.com
References
- Intellinet Network Solutions - Provider of PoE and Data Center Product
- DropCatch.com
- Intellinet Network Solutions Account and Product Registration
- Intellinet Network Solutions Account and Product Registration
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>