INTELLINET 508995 Industrial 4-Port Gigabit Ethernet PoE Switch Instructions

: October 30, 2023
: INTELLINET

Table of Contents

Instructions
Features
Placement
Power
Front Panel
REGULATORY STATEMENTS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

INTELLINET 508995 Industrial 4-Port Gigabit Ethernet PoE++ Switch Instructions

Instructions

The Intellinet Industrial 4-Port Gigabit Ethernet PoE++ Switch with 2 SFP Ports offers an array of time-saving, cost-effective features while providing superior network throughput. No configuration is required and installation is plug and play.

Features

Provides power and data connections for up to four PoE network devices
IP40 slim-type metal housing to withstand harsh industrial conditions
Wide operating temperature: -20 – 75°C (4 – 167°F)
Option for DIN-rail installation
Two small form-factor pluggable GBIC module slots (SFP)
Two redundant DC inputs (48 – 57 V) with I/O terminal block

With a backplane speed of 12 Gbps, plenty of performance is available for your computers, servers and other networking devices. Each of the ports automatically senses the link speed of the connected network device and adjusts to 10, 100 or 1000 Mbps for compatibility and maximum performance. This PoE switch is designed to provide compatible devices with enough power when needed. It offers up to 95 watts of power per port until its power budget of 240 watts is reached.

For specifications, visit intellinetnetwork.com. Register your product at register. intellinet-network.com/r/508995 or scan the QR code on the cover

Placement

Desktop Installation

Prior to use, place/position the switch:

on a level surface that can support the weight of the switch and that offers at least 25 mm (approx. 1”) of clearance for ventilation;
away from sources of electrical noise: radios, transmitters, broadband amplifiers, etc.;
within 100 m (approx. 328’) of network devices it’s to be connected to.

DIN-Rail Installation

With DIN-rail bracket attached to device with screws, angle bracket onto DIN rail.
Push device in till it clicks into place.

Power

Chassis Ground Column
Located on the side of the power supply connector, a grounding terminal connector is used to provide proper grounding for your Intellinet Network Solutions switch. It should be wired to an object that provides earth ground.

Terminal Block Installation
NOTE: Ensure all power is off/disconnected before beginning!

Loosen appropriate screws.
Insert bare power-supply wires into appropriate terminals (positive wire into positive terminal; negative wire into negative terminal).
Tighten appropriate screws to secure wires. (If desired, repeat steps 1 – 3 on second input pair.)
Install block into the device and tighten screws.

Front Panel

LED	Color	Status	Status Description
PWR	Green	On	Power on
Off	Power off
Link 1 – 4	Yellow	On	Valid port connection
Blinking	Sending or receiving data
SFP 1 & 2	Green	Off	No link established.
PoE 1 – 4	Green	On	The connected Powered Device (PD) is receiving power.
Off	No PD is linked.

Cat5e/6/6a/8.x UTP/STP cables provide optimal performance; if a status LED doesn’t indicate a link or activity, check the corresponding device for proper setup and operation.

REGULATORY STATEMENTS

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of Federal Communications Commission (FCC) Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: reorient or relocate the receiving antenna;increase the separation between the equipment and the receiver; connect the equipment to an outlet on a circuit different from the receiver; or consult the dealer or an experienced radio/TV technician for help.

This device complies with the requirements of CE 2014/30/EU and / or 2014/35/EU. The Declaration of Conformity for is available at:
Symbol

North America IC Intracom America
550 Commerce Blvd.
Oldsmar, FL 34677, US
Asia & Africa
IC Intracom Asia 4-F, No. 77, Sec. 1, Xintai 5th Rd.
Xizhi Dist., New Taipei City 221, Taiwan
Europe
IC Intracom Europe
Löhbacher Str. 7, D-58553
Halver, Germany

All trademarks and trade names are the property of their respective owners.
INTELLINET Logo