SJCAM S1 Home Camera User Manual

June 11, 2024
SJCAM

SJCAM logo

Home Comera s1
User Manual
Please read this User Manual carefully before using the camera for the first time.

Safety instruction

  1. This camera uses high-precision components. Do not drop.
  2. Do not expose the unit to strong magnetic fields, such as magnets, electrical motors, and machinery that use strong radio waves.
  3. Never leave the unit in extreme high temperature areas. Electronics and optics can be damaged under prolonged exposure to high heat.
  4. Only use a MicroSD card from a known brand. Off-brand cards may deliver erratic results.
  5. Always store extra batteries in a sealed compartment away from sharp metal objects and away from moisture. Dispose damaged batteries immediately in proper recycling facilities in your area.
  6. Do not disassemble or burn the battery to avoid leakage or explosion of the battery.
  7. Please place this product in a cool, dry and dust-free place

Please choose an official collection point to recycle this product or its battery, and do not dispose of it in the trash.

Product Introduction

1. Led Light
2. Infrared Light
3. Lens
4. Light Sensitive Response Light
5. Microphone| 6. Indicator Light
7. Sensor
8. Speaker
9. 1/4 Screw
10. Usb
11. Memory Card Socket
---|---

Specification

Main Chip: Ingenic T31
Sensor: GC4663
Pixels: 4MP
Battery Model: 21700
Battery Capacity: 9200mah
Wifi: 2.4GHz
Lens Angle Of View: 95°
Fill Light: Super Bright Fluorescent Lamp
Night Vision Infrared Light: 8 Pcs
Video Encoding Method: H.264
Video Resolution: 2560×1440 15fps 1920×1080 15fps 1280×720 15fps
Thermal Induction Distance: About 10 Meters
Thermal Induction Angle: 143°
Microphone: Built-in
Speaker: Built-in
Single Machine Weight: 253g (With Battery)
Waterproof:  I P65
 Size:  90x55x44mm
Operating Temperature:  -10°C-45°C

Storage: plug-in Tf Card Above Class 10 Supports Up To 128gb

Charging

Charging Port: Micro Usb
Input Voltage:  5V
Input Current: 2A

Button Instruction

Power on/off: long press for 3 seconds
Network distribution button: Press twice in succession (under power-on state)

Download The App

Scan the QR code below to download the SJCAM Guard app

https://batterycam.sjcam.com

Bind the Camera
Press the power button on top of the camera twice in succession (picture 1), after hearing the beep, make sure that the status indicator light flashes slowly in red, open the “SJCAM Guard” app, and click “Add Device” on the APP homepage (picture 2), follow the guide steps in the APP to bind the device.

OTA Upgrade for the Camera
Open the “SJCAM Guard” APP, click the “Settings” icon in the device list on the APP homepage (picture 1) , and then click “Device Information” (picture 2) , the camera firmware upgrade can be detected in the “Device Information” (picture 3) .

SJCAM S1 Home Camera - picture 2

Unbind the Camera
Open the “SJCAM Guard” APP, click the “Settings” icon in the device list on the APP homepage (picture 1) , then slide down to find “Delete Device” (picture 2) , and then click “Delete Device” to unbind.

Share Camera with Friends

Open the “SJCAM Guard” APP, click the “Share” icon (picture 1) in the device list on the APP homepage, select the corresponding permissions ( picture 2) , and fill in the friends’ accounts to share with your friends (picture 3) . Note: Your friends must register an account in the “SJCAM Guard” APP.

SJCAM S1 Home Camera - picture 4

Playback Video
Open the “SJCAM Guard” APP, click the “Playback” icon (picture 1) in the device list on the APP homepage or switch to the video fragment in the “Events” (picture 2) to play (picture 3) .

SJCAM S1 Home Camera - picture 5

Packing List

Installation of Camera

Installation Method 1: Desktop Placement
Installation Method 2: Bracket Ceiling Installation
Installation Method 3: Bracket Wall Mounting

SJCAM S1 Home Camera - picture 7

Camera Ceiling/wall Installation Operation Diagram
Note: The installation wall must be able to bear 4 times total weight of the camera.

Schematic Diagram of Battery Disassembly and Assembly Operations
Note: Please use I NR 21700 3.7V 17.02 Wh rechargeable battery.

Battery Disassemble (Picture 1)

  • Use the disassemble stick or disassemble slice to gently pry open along the edge of the back cover;
  • Please use a 1.6mm cross screwdriver to remove the 6 screws of the battery cover and then gently loosen them and take battery out.
  • The battery can be removed after the battery cover is take off.

Battery Replacement (Picture 2)

  • Before replacing the battery, make sure that consistent the positive and negative poles of the battery
  • The positive pole corresponds to the positive pole of the battery compartment, and the negative pole corresponds to the negative pole of the battery compartment. After confirming that it is correct then put the battery into the battery compartment.
  • After replacing the battery, confirm whether the machine can be turned on normally, after confirmed it can be turned on normally then close the battery cover and lock the screws.

Remarks:

  1. To replace the battery, make sure that the positive and negative poles of the battery correspond to the positive and negative poles of the battery compartment.
  2. The screws must be tightened after closing the battery cover,or if not it will affect the waterproof performance of the camera.
  3. After the battery cover is removed, it should be placed in a clean area to ensure that it will not be stuck with other substances; other substances on the battery cover will affect the waterproof performance of the camera.

Troubleshooting

  1. The camera cannot be turned on. It may be that the battery is low, please use the 5V 2A power adapter to charge the camera until it is fully charged.

  2. The camera has no response when charging. It may be that the battery has entered protection. Connect the camera to the power adapter, charge it for 30 seconds, disconnect the power and repeat the operation 3 times; the battery can be activated.

  3. No cloud storage?
    S1 does not support cloud storage, save the video on the memory card.

  4. Unable to connect

  1. Check if your WIFI name and password are correct
  2. Make sure your WIFI is 2.4G not 5G
  3. Make sure your camera and mobile phone are close to the router
  1. How to replace the new Wi-Fi
  1. If the camera is online, open the “SJCAM Guard” APP, click the “Settings” icon in the device list on the APP homepage, and then click “Device Wi-Fi”, select a new Wi-Fi name and password to replace Wi-Fi
  2. If the camera is not online, you can reset the camera and re-bind
  1. No notification be pushed
  1. Make sure the camera “Notification push” is turned on
  2. Please enable “SJCAM Guard” APP notification authority in the phone settings

Product features may change with product upgrades or updates, please refer to the actual product specifications.
If you need after-sales service, please contact SJCAM customer service technical support email: support@sjcam.com
Welcome to visit SJCAM after-sales service webpage WWW.SJCAM.COM
Manufacturer: Shenzhen Zhencheng Technology Co., Ltd.

SJCAM logo

Made by Shenzhen ZhenCheng Technology Co.,Ltd.
3/F Building C, NO.2 Road 1, Shangxue Industyial Area
Bantian, Longgang District, Shenzhen, China
Made in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals