SJCAM F22s 4K PRO Drone User Manual

: June 10, 2024
: SJCAM

SJCAM F22s 4K PRO Drone

SJCAM-F22s-4K-PRO-Drone-product

Product Information

The SJ-Series GPS aircraft is an ultraportable and foldable remote-controlled (R/C) aircraft designed for outdoor use. It is operated using included parts and is intended for users over 14 years old.

Safety precautions must be taken when operating the aircraft. The R/C aircraft can be dangerous if not used correctly or if operated by someone who is not familiar with its use. It should be kept away from any persons, spectators, buildings, trees, structures, high-voltage wires, and operated in safe weather conditions. Moisture or water should also be avoided to prevent damage to the aircraft. The aircraft should only be operated with original parts made by SJ- Series and within the intended use of the product.

Product Usage Instructions

Before operating the R/C aircraft, read all instructions and warnings carefully.
Keep the R/C aircraft far away from any persons or spectators when flying.
Avoid flying in adverse weather conditions such as rain, electrical storms, and high winds to ensure safety of the user, any spectators, and surrounding property.
Avoid any moist environments as they may cause damage to the mechanical and electronic parts of the aircraft.
Only operate with included parts for intended use. Using un-approved parts will void warranty.
Do not use for any illegal purpose or use beyond the scope of which your local laws and regulations have stipulated.
Operate the aircraft under the guidance of a more experienced user if you are a new user or are having difficulties operating it.
Do not operate under the influence of drugs or alcohol.
Keep a safe range from aircraft when using top speed.
Refer to the instruction manual for future reference and maintenance.

In order to make sure that it meets the requirement of the electromagnetic environment of the aviation radio station, flying within the scope of 10 kilometers on each side by taking the airport runway center line as the middle line is HIGHLY FORBIDDEN or flying within the scope of 20 kilometers by taking both ends of the runway as the center is HIGHLY FORBIDDEN. Flying on the route of the airline is also PROHIBITED. Stop using all kinds of flying models or unmanned Quad-rotors in the AREA that prohibited by related authority or department of our country.

PREFACE

Thank you for purchasing the SJ-Series GPS aircraft. Please read all instructions and warnings carefully before operating. Please also keep this instruction manual for future reference and maintenance.
IMPORTANT:

This product shoud be operated by the people who are over 14 years old. It is a precision device; integrating machinery and electronics with air mechanics and high frequency transmission. It requires correct assembly and debugging to avoid any accident. The user should operate and control this product in a safe manner. In case of incorrect operation, it may cause serious injury or damage property. It can also be lost due to incorrect operation.
This product is suitable for experienced UAV pilots no less than 14 years of age.
In the event of a problem during using, operating, or maintenance, please contact the local sales agent or retailer or keep in touch with the responsible staff of our company.

SAFETY PRECAUTIONS

This R/C aircraft can be dangerous when in use, please make sure you keep it far away from any persons or spectators when flying. In-correct installation, poor conditions, or users not familiar with operation may cause damage to the aircraft or injure people or may cause an unexpected accident. Please pay close attention to flying safety and learn to recognize more dangerous conditions which may cause an accident due to your own negligence.

Keep it far away from any structures or crowds.
- This R/C aircraft may vary slightly in speed or sensitivity while flying and can cause potential danger. Therefore, please keep it far away from crowds, buildings, trees, structures, high-voltage wire, etc. Please also avoid flying in adverse weather conditions such as rain, electrical storms, and high winds to ensure safety of the user, any spectators, and surrounding property.
Keep it away from any moist environment.
- The inside of the aircraft is composed of many precision electronic and mechanical parts. Therefore, please try to avoid any moisture or water content from entering the main body of the aircraft as it may cause a breakdown of the mechanical and electronic parts and thus cause an accident.
Only operate with included parts for intended use.
- Please use the original parts made by SJ-Series for any re-equipping or maintenance to ensure flying safety. Please operate and use only under the scope of the product function permitted. Using un-approved parts will void warranty.
- DO NOT use for any illegal purpose or use beyond the scope of which your local laws and regulations have stipulated.
Avoid controlling it independently.
- New users may have certain difﬁculties during the early stages of learning to operate this aircraft. Please try to avoid operating the aircraft alone. When available, always operate this aircraft under the guidance of a more experienced user.
Do not operate under the influence of drugs or alcohol.
- Please operate this R/C aircraft according to your own state and flying skill. Any fatigue, bad mental state, or incorrect operation may increase the probability of accidental risk.
Please keep a safe range from aircraft when using top speed.
- When the operator is flying in high speed, please keep the aircraft far from the pilot and any surrounding persons or objects so as not to cause danger or damage.
Store it in a cool, dry place.
- The R/C aircraft is composed of material such as metal, ﬁber, plastic, electronics, etc. Therefore, please keep it away from any heat source and avoid prolonged exposure to direct sunlight. Excessive heat exposure can cause distortion and damage.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interfer-ence to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Please note that changes or modiﬁcations not expressly approved by the party responsible for compliance could void the use’s authority to operate the equipment.

WARNING

There is important information contained in this package and instruction manual, please keep it for future reference.
You have the responsibility to make sure that this model of aircraft won’t cause injury to others’ body or cause any damage to property.
Please operate strictly as shown on the instruction manual when debugging or assembling this aircraft. During the process of flying or landing, please pay more attention to keep 1-2 meters between the user and the aircraft to avoid colliding to the head or face or body, which may cause injury.
Our company and distributors won’t be responsible for any incorrect operation, which may cause loss or damage or injury to the body.
Children ages 14 and up should use this product under the guidance of an adult. This product is FORBIDDEN to be used by children under 14 years old.
Please correctly assemble and use this product as shown on the instruction manual or packing instruction. Some parts should be assembled by an adult.
Small parts are included with this product. Please place it beyond the reach of the children to avoid a CHOKING HAZARD or parts being mistakenly swallowed.
Playing on the road or near high trafﬁc areas is strictly FORBIDDEN so as not to cause an accident.
Please dispose of the packing material timely so as not to cause injury to children.
Please DO NOT disassemble or re-equip the aircraft as it may cause a breakdown of the aircraft during flying.
Batteries in the battery compartment of the charger should be inserted into the designated power source which has the same logo as the product.
Built-in rechargeable 3.7V lithium polymer battery included in the remote control.
Only the original charger made from our factory can be used.
Charger is not a toy.
When charging the battery, please conduct it under the surveillance of an adult. Please also keep it far away from any combustible object when charging. Please keep this aircraft within eyesight when charging.
Please DO NOT make it short-circuited or squeeze the battery so as not to cause an explosion.
DO NOT mix the Li-ion battery with a different type of battery.
Intelligent lithium battery is loaded in the Quad-rotor. Both built-in or external can be used for charging.
Please DO NOT make the battery short-circuited or decompose the battery or throw the battery into the ﬁre; DO NOT place the batteries near the high temperature or heated area (such as near the ﬁre or near the electric heating device).
The aircraft should be kept far away from any other electric compliance or equipment as far as possible or kept far away from the place where having the magnetic object nearby as they may cause interference with each other.
Please keep the safe distance from the high-speed rotating rotor so as not to cause twisted or danger of being wounded or being cut.
Engine will heat up. Please DO NOT touch it to avoid being burned or injured.
Please DO NOT close this product to your ear as it may cause injury to your hearing.
Type-C 5V wall charger recommended for charging. DO NOT use any charger stronger than 5V.
To comply with the command of the magnetic environment requirement formulated by the Aviation Radio Bureau and the related authority, during the regulated period in certain areas, please stop using the remote control of this model when such regulation command is issued.
Keep your UAS within sight.
Never fly over groups of people.
Never fly over stadiums or sports events.
Understand airspace restrictions and requirements.

WARNING: Product should only be used by adults and children 14 years and older. Adult supervision required for children under 14 years of age.
WARNING: CHARGING OF THE AIRCRAFT BATTERY MUST BE SUPERVISED AT ALL TIMES BY AN ADULT. UNPLUG THE BATTERY WHEN FULLY CHARGED. DO NOT OVER-CHARGE THE BATTERY.

EXEMPTION

When using this product, SJRC shall not be responsible for direct or indirect damages caused by the following reasons:

The damage caused by the user in the condition of drinking, drug taking, drug anesthesia, dizziness, fatigue, nausea and other poor physical or mental conditions.
Personal injury, property loss and legal liability caused by the user’s subjective intention or wrong judgment.
Compensation for any related spiritual damage caused by the accident.
Damage caused by users flying in flight areas prohibited by laws and regulations such as nature reserves.
Other damage caused by poor operation of Quadrotor due to re-equipment training or replacement of accessories or parts not produced by SJRC.
The Quadrotor sends low-pressure alarm and still does not land, resulting in the Quadrotor falling down.
Damage caused by forced flight knowing that the Quadrotor is in an abnormal state (such as water, oil, soil, sand or other unknown substances mixed in or the assembly is not completed or the main components have obvious faults or the accessories have obvious defects or missing).
Damage caused by the Quadrotor flying in magnetic interference area, radio interference area (such as areas near high-voltage power lines, large power equipment, radio and television transmission towers, mobile phone base stations, etc.), no fly area speciﬁed by the government, or the user’s vision is in backlight, blocked by obstacles, blurred vision, poor magic power and other conditions unsuitable for control.
Fly in bad weather, such as rain or wind (more than level 4), snow, hail or other bad weather.
The Quadrotor encounters collision, overturn, ﬁre, explosion, lightning strike, storm, tornado, rainstorm, flood, tsunami, ground subsidence, ice subsidence, cliff collapse, avalanche, hail, debris flow, landslide, earthquake, etc.
Damage caused by infringement of any data, audio or video data obtained by the user using the Quadrotor.
For the battery, such as damage caused by improper matching of protection circuit, battery pack and charger.
Any indirect losses or legal liabilities caused by problems of equipment or accessories (including memory cards), for example, images or videos that cannot be saved.
Losses or legal liabilities caused by the user’s reckless unsafe flight without completing sufﬁcient flight training.
The user promises to use the product only for legitimate purposes and agrees to abide by these terms and any relevant policies or guidelines that may be formulated by SJRC. Some details of this document may change with the upgrade of the product software version. Please read the upgrade details carefully before upgrading the software version. The instruction manual will be updated with or without prior notice.

FLY SAFETY

WIFI transmission area requirements:

Make sure correctly open the remote control antenna.
Make sure fly in the open area without any interference and obstacle.
Do not fly against the wind;WIFI transmission distance is 3.5KM.

Avoid flying over or near obstacles, crowds, high voltage power lines, trees, airport or bodies of water.
DO NOT fly near strong electromagnetic sources such as power lines and base stations as it may affect the onboard compass.
DO NOT use the drone in adverse weather conditions such as rain, snow, fog and wind speeds exceeding 7 m/s or 16 mph.
It’s important to understand basic flight guidelines, for the safety of both you and those around you. Don’t forget to read the Safety Guidelines before flight.

AIRCRAFT

AIRCRAFT DIAGRAM

axis mechanical gimbal with 4K electronic image stabilization camera
Propeller
Motor
LED indicator
Intelligent battery
Obstacle avoidance module
Night light
Optical flow sensor

A. Open the gimbal cover buckle.
B. Pull the gimbal cover up then gently take it off.

ASSEMBLE THE PROPELLER ****

ASSEMBLE THE PROPELLER A

Hold the motor, put the propeller in the motor spindle, aim at the propeller clip with the motor groove, press it down and rotate it in counter-clockwise direction.

ASSEMBLE THE PROPELLER B

Hold the motor, put the propeller in the motor spindle, aim at the propeller clip with the motor groove, press it down and rotate it in clockwise direction.

TAKE THE PROPLLER A OUT:

Hold the motor, press the propeller down and rotate it in clockwise direction.

TAKE THE PROPLLER B OUT:

Hold the motor, press the propeller down and rotate it in counter-clockwise direction.

LANDING GEAR

As shown in the picture above, please unfold the two front landing gears separately.
Please unfold the landing gears(shown as above)before flight, otherwise it may affect the WIFI image transmission distance.

INTELLIGENT FLIGHT BATTERY

Battery switch
Battery power indicator
Type-C charging port

Hold the switch button for 3 sec. power on; then press the button for 3 sec. power off.
When the battery in low voltage,Blue indicators will be blinking, now please charge the battery

REMOTE CONTROL

REMOTE CONTROL FUNCTIONS

Throttle stick
Direction stick
Click once then keep pressing for 3 seconds to emergency stop
Click once to check the electric quantity; then keep pressing for 3 seconds to power on
Click once speed switch; keep pressing for 3 seconds to enter the altitule mode
Click once to RTH mode;
Click once take photo, keep pressing for 3 seconds to turn on the night light.
Click the button to take video
Zoom in and out
Adjust the angel of camera up and down
Communication connection interface
Charging port
Long-distance version
Electric quantity of remote control
GPS signal intensity
Remote control signal intensity
Photo/video
Speed
Status Display
Electric quantity of aircraft
Distance
Height
Flight speed
Ascend/Descend speed

Tips: When the remote control is in low power, Keeps flashing, now you need to charge the remote control.

REMOTE CONTROL OPERATING METHOD

Throttle Joystick
Direction Joystick

DUAL REMOTE CONTROLLER MODE

Power off the remote control.
Keep pressing the and clicking the twice at the same time.(Click once power on to check the elecric quantity; then keep pressing for 3 seconds to power on). Now the right joystick is the throttle stick. LCD screen appears”R HRMD MODE”, now the right joystick turns to throttle operating mode. Turn off the remote control and turn it on again,now the left joystick turns to throttle operating mode.

LITHIUM BATTERY

CHARGE THE BATTERY

Press the buckle and take out the battery from the aircraft. SJCAM-F22s-4K-
PRO-Drone-fig-22

Phone adapter: 5V 3A (Not included) Support QC3.0
Charging time: About 3.5 hours (Depending on Charging adapter)
Remote control charging method

LITHIUM BATTERY CHARGING INSTRUCTIONS

Either power on or power off, the aircraft can be charged. Connect the Type-C charger to an DC power supply(4.5V-5.5V,2A-3A), and then connect with the charging port of the aircraft, when in charging, the indicator on the aircraft will become Blue blinking; All indicators keep solid on means charging completed.
Aircraft can be charged by the mobile power or car-loaded power.
Charging time of aircraift takes about 3.5 hours; operating time takes about 35 min.
Remote control is built-in 3.7V 1500 mAh lithium polymer battery, charging time takes about 2 hours, operating time about 2 hours. (When in charging, the indicator on the remote control become Red; when fully charged, the indicator on the remote control will turn to solid Green).

FLIGHT

STEP 1: Insert the connector cable on the remote control with the mobile device, click once to check the elecric quantity; then keep pressing for 3 seconds to power on.
(It takes about 45 seconds for the frequency pairing after starting the system.)

Step 2: Turn on the aircraft and set down on a level surface
The aircraft will auto-trim to this level surface.
Four aircraft arms — Blinking Red.
Power on the remote control and link the aircraft automatically.
Lights flashing blue (back) and white (front).

STEP 3:FREQUENCY PAIRING INSTRUCTION

Enter into the APP first page following the instructional video.

Step 4: Compass Calibration

Compass Calibration Part 1

Push the joysticks into the 1 & 11 o’clock position.
Lights rapid-blinking Blue / red (back) and White / red (front).
App aircraft status: “Compass calibration”.
Remark: The compass will be calibrated automatically when the magnetic interference occur, it is necessory to calibrate the compass manually

Step 5: Compass Calibration–Part 1

Pick up the aircraft horizontally and turn it around with your body(360°) and the remote control will send out a beeping sound.
Blue light + red light (front) of the aircraft– Solid on.

Step 6: Compass Calibration–Part 2

Pick up the aircraft from the bottom, head of the aircraft facing down and follow your body for a complete circle (360°).
Now remote control makes “DI”sound.
White light + red light (front) of the aircraft– Solid on.
APP Status: Please place the aircraft on a level ground and hold the aircraft stationary until the head of the pendant recallocates.

Step 7: GPS Searching(DO NOT use GPS Mode indoor)

Reposition the aircraft on a horizontal surface.
Blue light (rear) + White light (front) of the aircraft keep slowly flashing. It means the
GPS enters into the state of Satellite Search.
It takes a few minutes to complete this step.
Blue light (rear) and White light (front) of the aircraft shows Solid on, this means the GPS satellite searching is successful.
NOTICE: Fly in open areas, tall structures and large metal structures may affect the accuracy of the onboard compass and GPS system. Please search the GPS signal in the open areas.

Step 8: Calibrate Gyroscope

Push the joysticks into the 11 & 1 o’clock position.
Blue light (rear) + White light (front) of the aircraft: Keep flashing quickly.
App Drone Status: “Gyroscope calibrated”

Step 9: Reset to factory Setting / Level calibration

Push the throttle lever of the remote control to the “7” o’clock position and push the direction lever to the “1” o’clock position.
Blue light (rear) + White light (front) of the aircraft: Keep flashing quickly.
App Status: “ Reset to factory Setting / Level level calibration”
Precautions: Please put the aircraft on the horizontal ground for the restore factory setting.Otherwise it may affect the flight attitude.

Step 10: Starting/Stopping motors

Push the joysticks into 5 & 7 o’clock position.
Motors automatically to start, push the left joystick to take off the aircraft. (Starting the motors before the aircraft taking off).
NOTE: Starting the motors should be set before the aircraft take off.

Stopping Motors:

Pushing the joysticks into 5 & 7 o’clock position again, motors stop working.
The motors will stop working if the motors starting are not operated after 20 seconds.

All LEDs on the front arms and rear arms, you are ready to fly!

Blue (rear) and Blue (front) lights are all solid (no blinking).
App aircraft status: “Ready to fly”.
NOTICE: If the LED indicators on the arms of the aircraft : blue light (rear) + blue light (front) keep slowly flashing means the GPS signal is weak; Please keep pressing for 3 seconds to turn off the GPS mode: blue light (rear) keeps flashing + white light (front) is solid on, aircraft enter into the flight altitude mode, now the aircraft can take off.

SJ F PRO APP

DOWNLOAD THE SJ GPS PRO APP
- QR code of “SJ F PRO” software for Apple IOS system
- QR code of “SJ F PRO” software for Android system
APP INTRODUCTION

Wait until the aircraft Status says “Ready to Fly” before initiating flight.
This will ensure that your GPS is synced and your aircraft is ready to fly.

Back to Main Menu
Compass interference
Remote Battery
GPS Signal
Aircraft Battery
Setting
Auto Take-off
GPS Return Home
More Functions
SD card status
Shooting Function
Shutter

One-key fly far

Keep the distance between the aircraft and the target is more than 2 meters,adjust the lens manually to aim at the target.
Click the One-key far fly icon in the APP and slide to conﬁrm.
Click the One-key far fly icon in the APP again or pull the direction lever on the remote control to exit the far-fly function.

Remark: When starting the flight, the aircraft will move back about 25 meters away from the target and start the video shooting function at the same time. The aircraft will automatically return to the take-off point after performing the completion function. Pull the direction lever to exit. Pay attention to the backward direction of the aircraft.
Make sure there are no obstacles or crowds nearby so as to avoid any injury. In case of emergency, please pull the direction lever on the remote control immediately to stop the flight!

One-key Skyrocketing

Keep the distance of the aircraft with the target below more than 2 meters,then adjust the lens manually to aim at the target.
Click the One-key skyrocketing icon in the APP ,and slide to conﬁrm.
Click the One-key skyrocketing icon in the APP again or pull the direction lever on the remote control to exit the Skyrocketing function.

Remark: When starting the flight, the aircraft will automatically rise about 15 meters height and start the video recording at the same time.
The aircraft will automatically return back to the take off point after performing the completion function. Pull the steering lever to exit. Make sure there no obstacles above the aircraft so as to avoid any injury. In case of emergency, please immediately pull the direction lever of the remote control to stop the flight!

One-key Spiral

Keep the distance between the aircraft and the target at about 2 to 5 meters and manually adjust the lens to aim at the target.
Click the One-key spiral icon in the APP,and slide to conﬁrm.
Click the One-key spiral icon in the APP again or pull the direction lever on the remote control to exit the spiral function.

Remark: When starting the flight, the aircraft will automatically spiral up (with a maximum radius of about 15 meters) and start the video shooting function at the same time. The aircraft will automatically return to the take off point after performing the completion functions. Push the direction lever to exit. Make sure there are no obstacles or people around the aircraft so as to avoid any injury. In case of emergency, please immediately pull the direction lever on the remote control to stop the flight!

Vertical-screen Aerial Photograph
Click the Vertical-screen Aerial Photograph icon in the “Shooting Function” on the right side of the preview page of the APP and the mobile screen will appear vertical screen.
Time-lapse Photography

Click the APP function page, Shooting Function–Time-lapse Photography
Slide to select the Delay Magniﬁcation and click OK.
Click the to start time-lapse photography.
Click the again to ﬁnish shooting.

Panoramic Shooting

Click the APP function page and select the
Click the .
The aircraft rotates about one circle (360°) to complete panoramic shooting, automatically synthesize a panoramic picture, and save it in the photo album. When successfully finish shooting, a prompt message will pop up.

Open the APP and click ,enter into media library (Pic.1).
Click , enter into the share interface (Pic.2), choose one or all photos you like to share, click , choose the social media you like to share the photos (Pic.3).

Reminder: You can share 1 picture or 9 pictures at the same time. But Only one video can be shared each time.

HOW TO SEARCH THE LOST DRONE

Continue to click to open the MAP surface to search the aircraft.
The last position of lost aircraft will be appeared on the MAP.

FLIGHT

The Default GPS Mode is BEGINNER MODE:

Flight Distance is between 0-30 M.
Flight Altitude is between 0-30 M.
RTH Altitude is under 20 M. You can Turn-off the BEGINNER MODE to set the parameters in the APP from the smart phone.

SAVE THE PHOTO AND VIDEO TO THE MOBILE APP ALBUM

SJCAM-F22s-4K-PRO-
Drone-fig-54

Open the APP and connect the WIFI with the aircraft, click the , enter into the media library (Pic.1).
APP album: Choose photo and video and save them in the mobile album, click , photo and video are saved in the mobile album.
SD card : Click , choose photo and video and save them in your mobile, click , photo and video are saved in the mobile album.
NOTE: After shooting and recording finished, photo and video will be saved in the APP album and SD card, the resolution of photo and video saved in the APP album is different that in SD card.

AIRCRAFT FUNCTION PROFILE

WAY POINT FLIGHT
- Ensure the mobile internet connected, enter in the APP, catch the map data of the area when you intend to fly in your mobile device, then connect your mobile device with your aircraft, you can view the map from in the APP.
- Successfully connect the aircraft WIFI with your smart phone, click on the App, then you can find a RED CIRCLE(LIMITTED FLIGHT RANGE)/TAKEOFF POSITION/AIRCRAFT CURRENT POSITION on the map, mark the points (16 points at most) you plan to fly within the RED CIRCLE range on the map.
- If you would like to reset the points or flight route, click or . Click ,confirm to start Way Point Flight. Pushing the Right Joystick to cancel the Way Point Flight Function.

POINT OF INTEREST

Hover the aircraft at the center point to be surrounded.
Select the surrounding radius on the APP, and slide to flight.
When circling, you can control the left or right direction lever to change the clockwise flight or counterclockwise flight of the aircraft.
When circling, you can control the forward direction lever or the backward direction lever to change the circling radius of the aircraft.
Click the icon again on the APP to exit the Surround Function.

EMERGENCY STOP

Clicking once and keep pressing the for 3 seconds to enter into
Emergency Stop mode. It is activated if the flight height of aircraft within 13 meters; othterwise, it is not activated.
Only stop motors mid-flight in emergency when doing so can reduce the risk of damage or injury.

GPS FOLLOW-ME

When the Follow Me function activated, the aircraft will follow the GPS in your smart phone to follow you wherever you go. (Make sure the smart phone connect with the aircraft successfully, turn on APP on your smart phone.)

Make sure the flight scope is within 10-50 meters.
Click on the APP interface.
Waiting for APP aircraft Status to display “Follow Me ready” —Now the aircraft is moving along with the positioning coordinate on the APP.
Click the on the APP interface again to exit the Follow Me mode.

Common lssues:

GPS Follow-me function will be affected by the tall structures, trees and the living areas with WIFI signal inteference.
GPS Follow-me function is not activated if the GPS signal weak or GPS positioning OFF in the mobile device.
Use in open area and be mindful of your surroundings. Aircraft is NOT equipped with obstacle avoidance.

IMAGE RECOGNITION FOLLOW ME/GESTURE CONTROL

Click , choose , tap on the object or person you want to track, and tap to confirm your selection.
(NOTE: Make sure the size of the frame you mark is the same as the object or person you tap, the frame should not be too large.）

HAND GESTURE

Click on the APP, count down 3 seconds to 0 seconds with the hand motion to take photos or record the video, please follow the tips from the (PIC.1).

RETURN-TO-HOME (RTH)

The Return to Home (RTH) function bring the aircraft back to the Take Off
Point. This function only can be achieved under GPS mode.
There are 3 types of RTH: Smart RTH/Low-battery RTH/Fail connection RTH

Smart Return To Home

Press the Return to Home Button on your remote control or tap on the App of your smart phone, and the remote control will start beeping. Your aircraft will return to the TAKE OFF Point. Press the button again to stop RTH procedure. or alter the left and right joysticks to make the aircraft landing in the safe area.

Low-Battery return to home

Low-Battery RTH is triggered when the Flight Battery level is low, When low battery RTH activated, aircraft ascends or descends automatically at the height altitude of 30 meters, then you can alter the left and right joysticks to make it landing in the safe area. Aircraft returns to the take-off point if the current battery level can only support the aircraft long enough to decend from the current altitude.

Fail connection RETURN-TO-HOME (RTH)

Aircraft will enter Return to Home Mode if the signal to the remote control is lost. The aircraft will return to the take-off point. The aircraft may link the remote control automatically during the RTH activated. If links sucessfully, you can re-operate the aircraft.

WARNING:
This aircraft is equipped with obstacle-avoidance.

OBSTACLE AVOIDANCE

The valid scanning range is dead ahead 20 meters between the aircraft and obstable.
Operation principles of obstacle avoidane: Pulse signal is sent out by the transmission port. The pulse signal is received by the receiving port after the pulse signal returns once the obstacle found within the scanning range. The forward stop command is sent out after the distance between aircraft and obstacle is obtained by a series calculations.
The position of the aircraft stop to go ahead depends on the flight speed. When the aircraft flys dead ahead in low speed, forward stop command starts to sent out after the obstacle is scanned at the distance of 20 meters to the aircraft. The obstacle avoidance distance of the aircraft and obstacle is shorter if in high speed. Otherwise,it will be longer (20 meters at most).

OPTICAL FLOW VISION SYSTEM

The aircraft is equipped with a downward looking optical flow system, which is composed of downward looking visual camera sensors, so that the UAV can hover stably at low altitude without GPS or with weak GPS signals. SJCAM-F22s-4K-
PRO-Drone-fig-75

Note:

The optical flow vision system can only assist in flight when the surrounding environment is full of light and rich in texture but cannot completely replace the user’s judgment. Please pay attention to the aircraft situation and APP tips and please DO NOT rely too much on the optical flow vision system.
The optical flow vision system is ineffective or ineffective in situations where the ambient light is too bright or too dark, mirror surface, pure color smooth ground, water surface, reflective surface, texture sparse surface, etc.
The best working range of the down view optical flow vision system is below 0.5-3 meters. If it exceeds this range, the positioning effect of the down view optical flow vision system may be poor. Please fly with caution.
Please ensure that the lens of the optical flow vision system is clear and DO NOT block or interfere the optical flow vision system.
The optical flow vision system can only be used in the Alititude Mode and change to the GPS mode automatically outdoors after GPS satellite search successfully.

CAMERA FUNCTIONS

SJCAM-F22s-4K-PRO-Drone-fig-76

Click on the remote control, or click on the APP, the indicator will flash once, means the camera takes one photo.
Click on the remote control, or click on the APP, the indicator will keep flashing, means the camera is recording.
Press again to save the video.
DO NOT take photo during recording.
The Original images and videos are saved in the SD card. Press the SD card slightly to take it out, then insert the card into the card reader and insert into the Type-C outlet of a computer to read the data from SD card.
The images can be also viewed in the App.

COMMON SOLUTIONS

The mobile device and remote control cannot be connected.
- Check the status of control signal icon on the APP if changed.
The image transmission is jammed or easily out of control and disconnected.
Adjust the antenna angle to align with the aircraft, and ensure no obstruction in the middle position.
Change the flight area. Please DO NOT fly near high buildings or signal towers.
Update the latest firmware of the aircraft.
The aircraft hovers unsteadily.
Change the flight area. Please DO NOT fly near high buildings or signal towers.
Conduct aircraft compass calibration and horizontal calibration.
Judge whether the strong wind affects the flight or not.
Judge whether the fan blade and the arm are deformed or not.
The GPS accuracy of the aircraft is not accurate or cannot pass the GPS accuracy test.
Go to an open area outdoors where GPS signal can be searched 6 or more satellites.
Walk around the aircraft at close range.
Replace the mobile device.
Do not test it under high buildings.
The battery cannot be charged.
Re-plug and unplug the charger or re-load and unload the battery.
Short flight time.
- Overcharge or discharge the battery, also the battery life reducing can be caused by the high-temperature environment. It is recommended to store the remaining 60% of the battery power and recharge it fully before using.
Excessive inclination angle or abnormal problem of the UAV PTZ checking.
Re-start the aircraft on the flat ground to PTZ calibration.
Check the PTZ status if it works or not.
Choose the“ ”on the APP to restore the PTZ to original factory setting.
PTZ initialization fails
- Please take the PTZ protection cover off before turn on the power of the aircraft, then put it on the flat ground to PTZ calibration.
Unclear shooting.
Check whether the camera protective film is removed or not.
Use it under the good light environment.
Set shooting parameters from the camera setting in the APP.
The camera is misty.
Wet weather causes fog on the camera. Replace the storage place of the aircraft.
Place desiccant in the protective cover of camera during storage.
Pictures or videos taken are lost.