PPI ProceX48 Process Indicator with Alarms User Manual

Proce X
Process Indicator with Alarms

User Manual

PANEL MOUNTING & ELECTRICAL CONNECTIONS

PANEL CUTOUTS

ELECTRICAL CONNECTIONS

FRONT PANEL AND OPERATION

PROCEX48 / PROCEX72 / PROCEX96

PROCEX48H

Table 2.1
KEY DEFINITIONS

up mode.

| **** DOWN| Press to decrease the parameter value. Pressing once decreases the value by one count; holding the key pressed speeds up the change.

| **** UP| Press to increase the parameter value. Pressing once increases the value by one count; holding the key pressed speeds up the change.

MAIN MODE DISPLAY
Upon switching on the power to the Indicator, all displays and indicators are lit on for approximately 3 seconds. This is followed by the indication of the Indicator model name for approximately 1 second. The Indicator now enters MAIN Mode wherein the display shows the PV proportional to the Input DC signal within user set Range Low and Range High Limits.

PV ERROR INDICATION
In case of PV Error the following messages are flashed.

Table 2.2

__

| Over-range (PV above Max. Range)

__

| __ Under-range (PV below Min. Range)

PARAMETER SETTINGS

The Indicator offers various parameters for setting-up the configuration and operation modes. Each parameter has a unique name and a settable value. For example, the parameter ‘Input Type’ is identified by its name and has the settable values ‘0-20mA / 4-20mA / 0-5V / 0-10V’.
Further, the parameters are organized under different groups. Each group of parameters is called PAGE. Each page is assigned a unique number for its identification and access. The various pages along with their parameters are described later. Follow the steps below for setting / changing any parameter value.

Follow the steps below for setting / changing any parameter value.

1. Keep PRG key pressed (approximately 5 seconds) until display shows PAGE ( ). Release the key.
2. Press PRG key again. Display shows page number 0.
3. Press PRG key if page 0 is the desired page number (operator page) or use UP / DOWN keys to set the desired page number and then press PRG key. The display now shows the name for the first parameter in the page.
4. Use UP / DOWN keys to select the desired parameter name.
5. Press PRG key. The display now shows the value for the selected parameter.
6. Use UP / DOWN keys to change the parameter value.
7. Press PRG key to save the new value. The display shows the name for the next parameter in the list.
8. Repeat steps 4 to 7 for any other parameter settings, if required.
9. For returning to Main Mode, keep PRG key pressed (approximately 3 seconds) until the display starts showing PV.

The following figures step-wise show an example of changing the value for the parameter ‘Resolution’ from ‘1’ to ‘0.1’. The parameter ‘Resolution’ is available on PAGE-12 and is second in the list. Notice that from MAIN Mode the appropriate page number is selected first and then the desired parameter name is selected for changing the value. Finally, PRG key is used to return back to MAIN Mode.

Table 3.1
PAGE – 0 : OPERATOR PARAMETERS

ALARM-1 SETPOINT
Available only if selected ‘Alarm-1 type’ is either ‘Process High’ or ‘Process Low’. This parameter value sets the Upper (Process High) or Lower (Process Low) Alarm Limit.| ** -1999 to 9999
(with selected Resolution)
ALARM-2 SETPOINT
Available only if selected ‘Alarm-2 type’ is either ‘Process High’ or ‘Process Low’. This parameter value sets the Upper (Process High) or Lower (Process Low) Alarm Limit.| ** -1999 to 9999
(with selected Resolution)

Table 3.2
PAGE – 1 : PV MIN / MAX PARAMETERS

MAXIMUM PROCESS VALUE
This gives the maximum PV recorded since Power-up or last reset| ** View Only
MINIMUM PROCESS VALUE
This gives the minimum PV recorded since Power-up or last reset.| ** View Only
RESET PV MONITOR
This command resets Maximum value and Minimum value to the instantaneous Process Value.|

Table 3.3
PAGE – 12 : INPUT CONFIGURATION PARAMETERS

INPUT TYPE
The Indicator is factory calibrated for DC Voltage (0-5V / 0-10V) and DC Current (0-20mA / 4-20mA). Select the appropriate input type as per the type of Input Signal.
Note : _
_For DC Voltage Input, keep Terminals 2 & 3 open.
For DC Current Input, keep terminals 2 & 3 shorted.| ****

Controller Version :

RESOLUTION
Decimal Point for the displayed value.|
Parameter Description| Settings
---|---
DC RANGE LOW AND
DC RANGE HIGH
Set Range High as the value corresponding to Maximum input signal level and Range Low as the value corresponding to Minimum input signal level.| **** -1999 to 9999

(with selected Resolution)

OFFSET FOR PV
Zero offset for measured PV. Displayed PV = Actual PV + Offset| **** -1999 to 9999

(with selected Resolution)

Table 3.4
PAGE – 11 : ALARM PARAMETERS 

ALARM-1 TYPE
Type for Alarm-1.|
ALARM-1 HYSTERESIS
Differential (dead) band between the ON and OFF alarm states. Keep it large enough to avoid frequent switching.| 1 to 999 (with selected Resolution)
ALARM-1 LOGIC
Normal : The alarm-1 output remains ON under alarm conditions; OFF otherwise.
Reverse : The alarm-1 output remains OFF under alarm conditions; ON otherwise.|

ALARM-1 INHIBIT
Yes : The alarm-1 is suppressed during start-up alarm conditions.
No : The alarm-1 is not suppressed during start-up alarm conditions.|

ALARM-2 TYPE
Type for Alarm-2.|
ALARM-2 HYSTERESIS
Same as Alarm-1 Hysteresis.| 1 to 999 (with selected Resolution)
ALARM-2 LOGIC
Same as Alarm-1 Logic.|
ALARM-2 INHIBIT
Same as Alarm-1 Inhibit.|

Process Precision Instruments
101, Diamond Industrial Estate, Navghar, Vasai Road (E),
Dist. Palghar – 401 210.Maharashtra, India
Sales : 8208199048 / 8208141446
Support : 07498799226 / 08767395333
sales@ppiindia.net, support@ppiindia.net
www.ppiindia.net

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>