SEALEY WL63-8D 6 SMD LED Dimmable Rechargeable Dual Mounting Magnifying Worklight Instruction Manual

SEALEY WL63-8D 6 SMD LED Dimmable Rechargeable Dual Mounting Magnifying

Worklight

Specifications:

• Model Number: WL63/8D
• LED Type: SMD
• Power Supply: 5V-1A

Product Usage Instructions

Safety

• Inspect the cable and connector for wear and damage before connecting to the power supply. Do not use if worn or damaged.
• Ensure the lamp is fully charged before initial use.
• Do not charge in damp conditions.
• Do not turn the lamp on when it is being charged.
• Avoid shining the light directly into your eyes.
• Keep away from children.
• Avoid handling or moving the lamp while it is being charged.
• Do not use the lamp if you suspect damage to the battery or lamp casing.
• Recharge the battery immediately if in a discharged state and recharge at least once every six months of non-use.
• Do not attempt to open, disassemble, modify, or service the battery pack.
• Avoid crushing, puncturing, shorting external contacts, or disposing of in fire or water.

Introduction

The product features a powerful three-dioptre 109mm & eight-dioptre 24mm precision lens for high-quality magnification. It includes six SMD LEDs producing up to 60 lumens for illumination, and a touch-sensitive dimmer switch. The magnifier can detach from its base and clamp to a workbench up to 45mm thick, making it ideal for electrical engineers, engravers, and fine detail work. It is equipped with a rechargeable 3.7V 400mAh lithium cell battery and comes with a micro USB cable.

Operation

Refer to the instruction manual for detailed operation guidelines.

FAQ:

• Q: What should I do if the battery is in a discharged state?
  A: Recharge the battery immediately. Before storage, fully recharge the battery, and subsequently recharge the battery at least once every six months of non-use.

• Q: Can I charge the lamp in damp conditions?
  A: No, do not charge the lamp in damp conditions as it may cause damage.

• Q: How often should I inspect the cable and connector for wear and damage?
  A: Inspect the cable and connector before each use to ensure safety.

MODEL NO : WL63/8D

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

• Refer to the instruction manual

SAFETY

• Inspect the cable and connector for wear and damage to ensure items are safe before connecting to the power supply. If worn or damaged DO NOT use.
• Ensure the lamp is fully charged before initial use.
• DO NOT charge in damp conditions.
• DO NOT turn the lamp on when it is being charged.
• DO NOT shine directly into your, another person’s or an animal’s eyes.
• DO NOT allow children to use the lamp.
• DO NOT handle or move the lamp whilst it is being charged.
• DO NOT use the lamp if you suspect that the battery or the lamp casing is damaged.
• DO NOT leave the battery in a discharged state, recharge battery immediately. Before storage, fully recharge the battery, subsequently recharge the battery at least once every six months of non-use.
• DO NOT attempt to open, disassemble, modify or service the battery pack.
• DO NOT crush, puncture, short external contacts or dispose of in fire or water.
• DO NOT expose to temperatures above 40°C (104°F).

INTRODUCTION

Powerful three-dioptre 109mm & eight-dioptre 24mm precision lens gives high- quality magnifying capabilities. Features six SMD LEDs producing up to 60 lumens to illuminate the object for improved detailed work. Built-in touch- sensitive dimmer switch. Magnifier can detach from its sturdy base and spring clamp to a workbench up to 45mm thick. Ideal for electrical engineers, engravers, and fine detail work. Rechargeable 3.7V 400mAh lithium cell battery. Supplied with micro USB cable.

SPECIFICATION

• Model no: WL63/8D
• LED Type: SMD
• Supply: 5V-1A

OPERATION

CHARGING:

1. Connect the micro-USB lead to the socket on the side of the base of the lamp (fig.1). Plug into the USB power supply and turn on.
2. While lamp is charging there is a red LED shining through the desk clamp surface just above the touch-sensitive switch.
3. Direct the lens away from your eyes before switching on.
4. Lightly tap the touchpad switch on the base to turn the lamp on . Lightly tap the touchpad switch again to turn off.
5. To modify the lamp output, press and hold the touchpad switch to dim or increase the light output.
6. The lamp may be either desk mounted or attached to any desk/bench edge up to 45mm thick by exposing the clamp after removing the base plate.

ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling center and disposed of in a manner that is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information

• NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
• IMPORTANT: No Liability is accepted for incorrect use of this product.

WARRANTY

Guarantee is 12 months from purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 [email protected] www.sealey.co.uk
© Jack Sealey Limited

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>